On Tue, Jun 20, 2017 at 1:26 AM, Hauke Mehrtens <hauke@xxxxxxxxxx> wrote:
> From: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
>
> The reset controllers (on xRX200 and newer SoCs have two of them) are
> provided by the RCU module. This was initially implemented as a simple
> reset controller. However, the RCU module provides more functionality
> (ethernet GPHYs, USB PHY, etc.), which makes it a MFD device.
> The old reset controller driver implementation from
> arch/mips/lantiq/xway/reset.c did not honor this fact.
>
> For some devices the request and the status bits are different.
>
FWIW,
Reviewed-by: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
One nit below.
> Signed-off-by: Hauke Mehrtens <hauke@xxxxxxxxxx>
> Cc: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/reset/lantiq,reset.txt | 29 +++
> drivers/reset/Kconfig | 6 +
> drivers/reset/Makefile | 1 +
> drivers/reset/reset-lantiq.c | 215 +++++++++++++++++++++
> 4 files changed, 251 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/reset/lantiq,reset.txt
> create mode 100644 drivers/reset/reset-lantiq.c
>
> diff --git a/Documentation/devicetree/bindings/reset/lantiq,reset.txt b/Documentation/devicetree/bindings/reset/lantiq,reset.txt
> new file mode 100644
> index 000000000000..bf62669b2b96
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/reset/lantiq,reset.txt
> @@ -0,0 +1,29 @@
> +Lantiq XWAY SoC RCU reset controller binding
> +============================================
> +
> +This binding describes a reset-controller found on the RCU module on Lantiq
> +XWAY SoCs.
> +
> +This driver has to be a sub node of the Lantiq RCU block.
> +
> +-------------------------------------------------------------------------------
> +Required properties:
> +- compatible : Should be one of
> + "lantiq,danube-reset"
> + "lantiq,xrx200-reset"
> +- offset-set : Offset of the reset set register
> +- offset-status : Offset of the reset status register
> +- #reset-cells : Specifies the number of cells needed to encode the
> + reset line, should be 2.
> + The first cell takes the reset set bit and the
> + second cell takes the status bit.
> +
> +-------------------------------------------------------------------------------
> +Example for the reset-controllers on the xRX200 SoCs:
> + reset0: reset-controller@0 {
> + compatible = "lantiq,xrx200-reset";
> +
> + offset-set = <0x10>;
> + offset-status = <0x14>;
> + #reset-cells = <2>;
> + };
> diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
> index d21c07ccc94e..1742c2293bc3 100644
> --- a/drivers/reset/Kconfig
> +++ b/drivers/reset/Kconfig
> @@ -41,6 +41,12 @@ config RESET_IMX7
> help
> This enables the reset controller driver for i.MX7 SoCs.
>
> +config RESET_LANTIQ
> + bool "Lantiq XWAY Reset Driver" if COMPILE_TEST
> + default SOC_TYPE_XWAY
> + help
> + This enables the reset controller driver for Lantiq / Intel XWAY SoCs.
> +
> config RESET_LPC18XX
> bool "LPC18xx/43xx Reset Driver" if COMPILE_TEST
> default ARCH_LPC18XX
> diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
> index 02a74db94339..112dba1db6b9 100644
> --- a/drivers/reset/Makefile
> +++ b/drivers/reset/Makefile
> @@ -6,6 +6,7 @@ obj-$(CONFIG_RESET_A10SR) += reset-a10sr.o
> obj-$(CONFIG_RESET_ATH79) += reset-ath79.o
> obj-$(CONFIG_RESET_BERLIN) += reset-berlin.o
> obj-$(CONFIG_RESET_IMX7) += reset-imx7.o
> +obj-$(CONFIG_RESET_LANTIQ) += reset-lantiq.o
> obj-$(CONFIG_RESET_LPC18XX) += reset-lpc18xx.o
> obj-$(CONFIG_RESET_MESON) += reset-meson.o
> obj-$(CONFIG_RESET_OXNAS) += reset-oxnas.o
> diff --git a/drivers/reset/reset-lantiq.c b/drivers/reset/reset-lantiq.c
> new file mode 100644
> index 000000000000..f4e7dfec477a
> --- /dev/null
> +++ b/drivers/reset/reset-lantiq.c
> @@ -0,0 +1,215 @@
> +/*
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published
> + * by the Free Software Foundation.
> + *
> + * Copyright (C) 2010 John Crispin <blogic@xxxxxxxxxxx>
> + * Copyright (C) 2013-2015 Lantiq Beteiligungs-GmbH & Co.KG
> + * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
> + * Copyright (C) 2017 Hauke Mehrtens <hauke@xxxxxxxxxx>
> + */
> +
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/reset-controller.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +#include <linux/property.h>
> +
> +#define LANTIQ_RCU_RESET_TIMEOUT 10000
> +
> +struct lantiq_rcu_reset_priv {
> + struct reset_controller_dev rcdev;
> + struct device *dev;
> + struct regmap *regmap;
> + u32 reset_offset;
> + u32 status_offset;
> +};
> +
> +static struct lantiq_rcu_reset_priv *to_lantiq_rcu_reset_priv(
> + struct reset_controller_dev *rcdev)
> +{
> + return container_of(rcdev, struct lantiq_rcu_reset_priv, rcdev);
> +}
> +
> +static int lantiq_rcu_reset_status(struct reset_controller_dev *rcdev,
> + unsigned long id)
> +{
> + struct lantiq_rcu_reset_priv *priv = to_lantiq_rcu_reset_priv(rcdev);
> + unsigned int status = (id >> 8) & 0x1f;
> + u32 val;
> + int ret;
> +
> + ret = regmap_read(priv->regmap, priv->status_offset, &val);
> + if (ret)
> + return ret;
> +
> + return !!(val & BIT(status));
> +}
> +
> +static int lantiq_rcu_reset_status_timeout(struct reset_controller_dev *rcdev,
> + unsigned long id, bool assert)
> +{
> + int ret;
> + int retry = LANTIQ_RCU_RESET_TIMEOUT;
> +
> + do {
> + ret = lantiq_rcu_reset_status(rcdev, id);
> + if (ret < 0)
> + return ret;
> + if (ret == assert)
> + break;
return 0;
> + usleep_range(20, 40);
> + } while (--retry);
> +
> + return retry ? 0 : -ETIMEDOUT;
return -ETIMEDOUT;
> +}
> +
> +static int lantiq_rcu_reset_update(struct reset_controller_dev *rcdev,
> + unsigned long id, bool assert)
> +{
> + struct lantiq_rcu_reset_priv *priv = to_lantiq_rcu_reset_priv(rcdev);
> + unsigned int set = id & 0x1f;
> + int ret;
> + u32 val;
> +
> + if (assert)
> + val = BIT(set);
> + else
> + val = 0;
> +
> + ret = regmap_update_bits(priv->regmap, priv->reset_offset, BIT(set),
> + val);
> + if (ret) {
> + dev_err(priv->dev, "Failed to set reset bit %u\n", set);
> + return ret;
> + }
> +
> +
> + ret = lantiq_rcu_reset_status_timeout(rcdev, id, assert);
> + if (ret)
> + dev_err(priv->dev, "Failed to %s bit %u\n",
> + assert ? "assert" : "deassert", set);
> +
> + return ret;
> +}
> +
> +static int lantiq_rcu_reset_assert(struct reset_controller_dev *rcdev,
> + unsigned long id)
> +{
> + return lantiq_rcu_reset_update(rcdev, id, true);
> +}
> +
> +static int lantiq_rcu_reset_deassert(struct reset_controller_dev *rcdev,
> + unsigned long id)
> +{
> + return lantiq_rcu_reset_update(rcdev, id, false);
> +}
> +
> +static int lantiq_rcu_reset_reset(struct reset_controller_dev *rcdev,
> + unsigned long id)
> +{
> + int ret;
> +
> + ret = lantiq_rcu_reset_assert(rcdev, id);
> + if (ret)
> + return ret;
> +
> + return lantiq_rcu_reset_deassert(rcdev, id);
> +}
> +
> +static const struct reset_control_ops lantiq_rcu_reset_ops = {
> + .assert = lantiq_rcu_reset_assert,
> + .deassert = lantiq_rcu_reset_deassert,
> + .status = lantiq_rcu_reset_status,
> + .reset = lantiq_rcu_reset_reset,
> +};
> +
> +static int lantiq_rcu_reset_of_probe(struct platform_device *pdev,
> + struct lantiq_rcu_reset_priv *priv)
> +{
> + struct device *dev = &pdev->dev;
> + int ret;
> +
> + priv->regmap = syscon_node_to_regmap(dev->of_node->parent);
> + if (IS_ERR(priv->regmap)) {
> + dev_err(&pdev->dev, "Failed to lookup RCU regmap\n");
> + return PTR_ERR(priv->regmap);
> + }
> +
> + ret = device_property_read_u32(dev, "offset-set", &priv->reset_offset);
> + if (ret) {
> + dev_err(&pdev->dev, "Failed to get RCU reset offset\n");
> + return -EINVAL;
> + }
> +
> + ret = device_property_read_u32(dev, "offset-status",
> + &priv->status_offset);
> + if (ret) {
> + dev_err(&pdev->dev, "Failed to get RCU status offset\n");
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int lantiq_rcu_reset_xlate(struct reset_controller_dev *rcdev,
> + const struct of_phandle_args *reset_spec)
> +{
> + unsigned int status, set;
> +
> + set = reset_spec->args[0];
> + status = reset_spec->args[1];
> +
> + if (set >= rcdev->nr_resets || status >= rcdev->nr_resets)
> + return -EINVAL;
> +
> + return (status << 8) | set;
> +}
> +
> +static int lantiq_rcu_reset_probe(struct platform_device *pdev)
> +{
> + struct lantiq_rcu_reset_priv *priv;
> + int err;
> +
> + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + priv->dev = &pdev->dev;
> + platform_set_drvdata(pdev, priv);
> +
> + err = lantiq_rcu_reset_of_probe(pdev, priv);
> + if (err)
> + return err;
> +
> + priv->rcdev.ops = &lantiq_rcu_reset_ops;
> + priv->rcdev.owner = THIS_MODULE;
> + priv->rcdev.of_node = pdev->dev.of_node;
> + priv->rcdev.nr_resets = 32;
> + priv->rcdev.of_xlate = lantiq_rcu_reset_xlate;
> + priv->rcdev.of_reset_n_cells = 2;
> +
> + return reset_controller_register(&priv->rcdev);
> +}
> +
> +static const struct of_device_id lantiq_rcu_reset_dt_ids[] = {
> + { .compatible = "lantiq,danube-reset", },
> + { .compatible = "lantiq,xrx200-reset", },
> + { },
> +};
> +MODULE_DEVICE_TABLE(of, lantiq_rcu_reset_dt_ids);
> +
> +static struct platform_driver lantiq_rcu_reset_driver = {
> + .probe = lantiq_rcu_reset_probe,
> + .driver = {
> + .name = "lantiq-reset",
> + .of_match_table = lantiq_rcu_reset_dt_ids,
> + },
> +};
> +module_platform_driver(lantiq_rcu_reset_driver);
> +
> +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("Lantiq XWAY RCU Reset Controller Driver");
> +MODULE_LICENSE("GPL");
> --
> 2.11.0
>
--
With Best Regards,
Andy Shevchenko
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH v4 10/16] reset: Add a reset controller driver for the Lantiq XWAY based SoCs
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: Re: [PATCH v4 10/16] reset: Add a reset controller driver for the Lantiq XWAY based SoCs
- From: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
- Date: Tue, 20 Jun 2017 02:29:58 +0300
- Cc: Ralf Baechle <ralf@xxxxxxxxxxxxxx>, Linux MIPS Mailing List <linux-mips@xxxxxxxxxxxxxx>, "open list:MEMORY TECHNOLOGY..." <linux-mtd@xxxxxxxxxxxxxxxxxxx>, linux-watchdog@xxxxxxxxxxxxxxx, devicetree <devicetree@xxxxxxxxxxxxxxx>, "martin.blumenstingl" <martin.blumenstingl@xxxxxxxxxxxxxx>, john <john@xxxxxxxxxxx>, linux-spi <linux-spi@xxxxxxxxxxxxxxx>, "hauke.mehrtens" <hauke.mehrtens@xxxxxxxxx>, Rob Herring <robh@xxxxxxxxxx>, Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>
- In-reply-to: <20170619222608.13344-11-hauke@hauke-m.de>
- References: <20170619222608.13344-1-hauke@hauke-m.de> <20170619222608.13344-11-hauke@hauke-m.de>
- Follow-Ups:
- References:
- [PATCH v4 00/16] MIPS: lantiq: handle RCU register by separate drivers
- From: Hauke Mehrtens
- [PATCH v4 10/16] reset: Add a reset controller driver for the Lantiq XWAY based SoCs
- From: Hauke Mehrtens
- [PATCH v4 00/16] MIPS: lantiq: handle RCU register by separate drivers
- Prev by Date: [PATCH v4 04/16] watchdog: lantiq: access boot cause register through regmap
- Next by Date: Re: [PATCH v4 12/16] MIPS: lantiq: Add a GPHY driver which uses the RCU syscon-mfd
- Previous by thread: [PATCH v4 10/16] reset: Add a reset controller driver for the Lantiq XWAY based SoCs
- Next by thread: Re: [PATCH v4 10/16] reset: Add a reset controller driver for the Lantiq XWAY based SoCs
- Index(es):
 |