Re: [PATCH v2 09/15] reset: Add a reset controller driver for the Lantiq XWAY based SoCs

[Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>]

On Tue, 2017-05-23 at 23:25 +0200, Hauke Mehrtens wrote:
> On 05/22/2017 11:33 AM, Philipp Zabel wrote:
> > Hi Hauke,
> > 
> > thank you for the patch. I have a few questions and comments below:
> > 
> > On Sun, 2017-05-21 at 15:09 +0200, Hauke Mehrtens wrote:
> >> From: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx>
> >>
> >> The reset controllers (on xRX200 and newer SoCs have two of them) are
> >> provided by the RCU module. This was initially implemented as a simple
> >> reset controller. However, the RCU module provides more functionality
> >> (ethernet GPHYs, USB PHY, etc.), which makes it a MFD device.
> >> The old reset controller driver implementation from
> >> arch/mips/lantiq/xway/reset.c did not honor this fact.
> > 
> > Does this driver replace arch/mips/lantiq/xway/reset.c?
> 
> This serial consists of multiple patches which are all together
> replacing this code. The RCU register block does controls multiple
> blocks in the SoC. One is the reset controller, but also the GPHY FW
> loading and some other unrelated stuff.

Thank you for clarifying.

> >> +		compatible = "lantiq,rcu-reset";
> >> +		lantiq,rcu-syscon = <&rcu0 0x10 0x14>;
> >> +		#reset-cells = <2>;
> >> +	};
> >> +
> >> +	rcu_reset1: rcu_reset {
> >> +		compatible = "lantiq,rcu-reset";
> >> +		lantiq,rcu-syscon = <&rcu0 0x48 0x24>;
> >> +		#reset-cells = <2>;
> >> +	};
> > 
> > I think these should be children of the &rcu0 node. Then you could use
> > the reg property to specify the registers.
> 
> The problem is that the RCU registers at offset 0x10 and 0x14 also have
> bits to indicate what caused the last hardware reset and which boot mode
> was selected by putting some pins to low or high level. I want to access
> the same register from the watchdog driver and probably form more
> positions which do not have anything to do with a reset controller.

That is ok, I just suggest to get the syscon regmap not from a phandle
property, but from the node parent. The reset controller is a part of
the RCU.

> > Also, have you considered using a binding like the ti-syscon-reset? 
> > That could remove the need for a rcu_reset node per register pair
> > altogether, but might not make sense if the reset registers are densely
> > populated.
> 
> Would your suggestion be something like this?
> 
> rcu_reset0: reset-controller {
> 	compatible = "lantiq,rcu-reset";
> 	lantiq,rcu-syscon = <&rcu0>;
> 	#reset-cells = <2>;
> 	ti,reset-bits = <
> 		0x48 0x24
> 		0x10 0x14
> 	>;
> };

Yes, for example. I'd put the reset-controller node inside the &rcu0
node and drop the lantiq,rcu-syscon property, though.

> I prefer to have two device tree nodes entries for these two register
> blocks.

If Rob is fine with this, I won't object. I'd just be interested to know
why.

regards
Philipp

--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html