Re: [alsa-devel] Fwd: [PATCH 1/1] SPI : spi-pxa2xx : fix spi init of WM510205 codec via ACPI (resend)

[Christian Hartmann <cornogle@xxxxxxxxxxxxxx>]

Hi,

> That implies the pdata is not set for the device when you are
> entering arizona_dev_init, also might be worth checking if it is
> calling the stub version of the full version (basically is
> CONFIG_OF turned on).
# CONFIG_OF is not set here, so the current code as in arizona_dev_init()

...
if (dev_get_platdata(arizona->dev,0)) {
/* currently not working... */
else
 arizona_of_get_core_pdata(arizona);

which returns only '0' in this case  because the config option
CONFIG_OF is disabled.

Today I am back at this device and I have changed the above function
(arizona_of_get_core_pdata) where I set
currently the pdata with its values for the arizona type = WM5102.

So the pdata is at the moment hardcoded, that is not the way I want to
go on, but
it seems the code works so far, except the LDO1 makes trouble with the
current GPIO value 0x17 (extracted from dsdt.dsl as seen above).

[    5.790655] systemd-journald[434]: Received request to flush
runtime journal from PID 1
[    7.263225] pxa2xx-spi 80860F0E:00: no DMA channels available, using PIO
[    7.263339] pxa2xx-spi 80860F0E:00: registered master spi32766 (dynamic)
[    7.263482] spi spi-WM510205:00: 8333333 Hz actual, PIO
[    7.263490] spi spi-WM510205:00: setup mode 0, 8 bits/w, 8000000 Hz max --> 0
[    7.263551] spi spi-WM510205:00: checking WM510205 with bmp180
[    7.263557] spi spi-WM510205:00: checking WM510205 with bmp181
[    7.263562] spi spi-WM510205:00: modalias WM510205 in id_table not
found, returns NULL
[    7.263610] arizona spi-WM510205:00: acpi_match_device() first,
than via spi_get_device_id().
[    7.263617] arizona spi-WM510205:00: matched ACPI ID and data
[    7.263621] arizona spi-WM510205:00: using 1 as type for arizona audio codec
[    7.263625] arizona spi-WM510205:00: regmap set to wm5102_spi
[    7.264424] arizona spi-WM510205:00: spi_irq = -1
[    7.264432] arizona spi-WM510205:00: arizona_irq = -1
[    7.264436] arizona spi-WM510205:00: arizona_spi_probe done, call
and return of  arizona_dev_init
[    7.264440] arizona spi-WM510205:00: dev_set_drvdata done for 1
[    7.264445] arizona spi-WM510205:00: arizona_of_get_core_pdata for 1
[    7.264450] arizona spi-WM510205:00: regcache_cache_only for 1 set
[    7.264454] arizona spi-WM510205:00: added wm5102_core_supplies for 1
[    7.269430] LDO1: Failed to request enable GPIO23: -517
[    7.269506] arizona spi-WM510205:00: Failed to register LDO1 supply: -517
[    7.289191] spi-WM510205:00 supply AVDD not found, using dummy regulator
[    7.289246] spi-WM510205:00 supply DBVDD1 not found, using dummy regulator
[    7.289366] spi-WM510205:00 supply DCVDD not found, using dummy regulator
[    7.289415] arizona spi-WM510205:00: Failed to request /RESET: -517
[    7.289690] pxa2xx-spi 80860F0E:00: registered child spi-WM510205:00

... arizona spi-wm510202 tries to init the device 2 times again ....

side-note: added a lot of dev_err to see whats going on, so the most
messages are not in master, only in my local branch (today its
4.2.0-rc6)

Instead of hardcoding and finding the correct GPIOs by Try&Error I
want as mentioned above already by Charles Keepax, to pull them from
ACPI.

currently I am not using the the gpiolib.h and its functions to get
the named and relevant GPIOs in question,
failing yet searching for examples which fits into the arizona mfd code easily.

I saw the drivers/gpio/gpio-arizona.h, which is also not using the
gpiolib.h, too.also it is not clear to me, if I should use
gpio-arizona at all (or extend it for using it with the wm5102).


zitat from Charles:

"I suspect we still have some issues with the GPIO lookups, I
suspect we want to actually pull them from ACPI rather than
putting them into the pdata, as I don't know if the number will
translate directly over."

What I have understand today :  the three values (irq_gpio, reset,
ldoena) have different 'parents' as seen in the dsdt.dsl
irq_gpio = _SB.GPO2 -> 0x0004
reset = _SB.I2C7.PMIC

Looking in other wmXXXX drivers how they get and set there gpios, but
nothing found what I can adapt or reuse here at the moment.

Does anybody has a clue??

cheers
chris
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html