-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Thanks for your reply. As far as I know, only grml big has speakup included, and I'm 99.9% sure that there's no way grml big will be happy with only 64 megs of ram. If grml small does in fact have speakup included, as far as using hardware synths goes, that would be a pleasant surprise. As for your comment about explaining too much, my motto is if in doubt, give more info than less. Thanks again, and a clarification on speakup in grml small from someone in the know would be appreciated, before I possibly go wasting bandwidth. Greg On Thu, Feb 10, 2011 at 03:19:39AM -0500, Pia wrote: > The best thing to do is get a GRML live CD. GRML talks and should work > as a live CD with your system. http://grml.org > > You can use a cheat code to start speakup and then mount /dev/sda1 or > whatever your root partition is on your hard drive and then from there > set up grub either by running grub or chrooting into the environment on > your hard drive and running grub from there. Note that it depends on > what is wrong as to whether you can get away without chrooting or not and > if you don't you also have to make sure you use the correct device names. > You can also edit /boot/grub/menu.lst and /boot/grub/device.map manually > as needed. Note that they will be under your mount point as well and so > the paths I gave will not be exactly what they will be once you boot > GRML. If I did not explain how to do this specifically enough, please > let me know, but if I was too obvious in the things I mentioned, I also > apologise. You sound like you are very competent with Linux, and so I > don't always know what I should or should not write as far as detail > goes. > > HTH, > > Pia > > On Wed, 9 Feb 2011, Gregory Nowak wrote: > >> -----BEGIN PGP SIGNED MESSAGE----- >> Hash: SHA1 >> >> Hi folks, >> >> I did a minimal upgrade on my debian system from lenny to squeeze, and >> rebooted after upgrading the kernel and udev, as the squeeze release >> notes say to do. This left me with an unbootable system. No, it's not >> because I ignored the warning to boot by label or uuid. I can tell >> from the initrd shell that the piix.ko module loads, but it tells me >> that both ide ports are disabled. This leaves me without sdax, or hdax >> devices under /dev, and no disks directory under /dev. I have the >> feeling that if I took out all_ide_generic out of the kernel command >> line, things would work. My problem however is grub. >> >> Once the system boots from the drive, I press ESC. From what I >> gathered by searching the web, in order to edit the command line of >> the first menu entry, I need to type e twice, arrow to where I want to >> edit, and press ctrl+x to get out of the editor. So, after hitting >> ESC, I press e twice, arrow right 80 times which should put me at the >> end of the line, and then backspace 21 times which should erase what I >> want to erase, and I then press ctrl+x to exit. From what I >> understand, I should then be able to hit b,and boot that entry, but >> when I hit b, nothing happens. >> >> So, I tried another approach I read about. I hooked up my serial synth >> to this machine (I normally use my doubletalk pc with speakup), and >> rebooted. I pressed ESC, pressed c to get into command mode, and >> typed: >> >> serial --unit=0 --speed=9600 >> terminal_output serial >> >> but again, nothing happened. >> >> Another alternative would be to solve this from a livecd system, but >> since this machine has 64 megs of ram, I haven't yet found a modern >> livecd which would work with that much ram. >> >> So, if someone familiar with legacy grub (not grub2) could please walk >> me through, key press by key press, on what I need to do to edit and >> boot the first menu entry, I'd really appreciate it. Better yet, if >> someone could please explain where I went wrong with the serial >> console part, so I can do what I need to do with feedback, that would >> be even better. >> >> I think I know why I've been so fond of lilo for so many years, it's >> less complicated, or should I say less flexible to use. I have no >> problem with flexibility, provided that I can get feedback on what I'm >> doing. Thanks much in advance for any help. >> >> Greg >> >> >> - -- >> web site: http://www.romuald.net.eu.org >> gpg public key: http://www.romuald.net.eu.org/pubkey.asc >> skype: gregn1 >> (authorization required, add me to your contacts list first) >> >> - -- >> Free domains: http://www.eu.org/ or mail dns-manager at EU.org >> -----BEGIN PGP SIGNATURE----- >> Version: GnuPG v1.4.9 (GNU/Linux) >> >> iEYEARECAAYFAk1TW/sACgkQ7s9z/XlyUyCmBQCgoJOpvPj/qNTBWYtT7f/5+4un >> t4wAn0GZMZ4u7utUOvwFt2GaDNbNCAoR >> =dkyI >> -----END PGP SIGNATURE----- >> _______________________________________________ >> Speakup mailing list >> Speakup at braille.uwo.ca >> http://speech.braille.uwo.ca/mailman/listinfo/speakup >> > _______________________________________________ > Speakup mailing list > Speakup at braille.uwo.ca > http://speech.braille.uwo.ca/mailman/listinfo/speakup > - -- web site: http://www.romuald.net.eu.org gpg public key: http://www.romuald.net.eu.org/pubkey.asc skype: gregn1 (authorization required, add me to your contacts list first) - -- Free domains: http://www.eu.org/ or mail dns-manager at EU.org -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.9 (GNU/Linux) iEYEARECAAYFAk1UMMQACgkQ7s9z/XlyUyDTPgCgvSieZU7qZuN/QYzZh5VN+G0B 8moAoJRzSpp4YDFXPGFU5tzd/Bo713YN =jyqr -----END PGP SIGNATURE-----
