Hello Janina,
Here is the information you wanted.
lsmod
Module Size Used by
vfat 12481 1
fat 39393 1 vfat
md5 3905 1
ipv6 217349 8
parport_pc 21249 1
lp 9133 0
parport 35977 2 parport_pc,lp
autofs4 20676 0
rfcomm 31708 0
l2cap 21061 5 rfcomm
bluetooth 40645 4 rfcomm,l2cap
sunrpc 141861 1
3c59x 33385 0
floppy 54001 0
sg 28513 0
microcode 5601 0
ohci1394 31577 0
ieee1394 285333 1 ohci1394
st 30429 0
dm_mod 47317 0
joydev 7169 0
usblp 10817 0
uhci_hcd 28505 0
speakup_acntsa 3657 0
speakupmain 51749 1 speakup_acntsa
pcspkr 3745 0
ext3 96937 1
jbd 66521 1 ext3
aic7xxx 146841 0
sd_mod 17473 0
scsi_mod 105361 4 sg,st,aic7xxx,sd_mod
[root at jerschmi l]# cat /etc/modprobe.conf
alias eth0 3c59x
alias scsi_hostadapter aic7xxx
alias snd-card-0 snd-emu10k1
install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 &&
/usr/sbin/alsactl restore >/dev/null 2>&1 || :
remove snd-emu10k1 { /usr/sbin/alsactl store >/dev/null 2>&1 || : ; };
/sbin/modprobe -r --ignore-remove snd-emu10k1
alias usb-controller uhci-hcd
alias ieee1394-controller ohci1394
[root at jerschmi l]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:60:97:73:72:91
inet6 addr: fe80::260:97ff:fe73:7291/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:1 carrier:1
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Base address:0x9800
----- Original Message -----
From: "Janina Sajka" <janina@xxxxxxxxxxx>
To: "Speakup is a screen review system for Linux." <speakup at braille.uwo.ca>
Sent: Sunday, October 10, 2004 8:49 AM
Subject: Re: 3c905 nic
> Sounds like a configuration issue to me. I've been using one of those
> cards for years, including today with Fedora 2.
>
> What does lsmod show?
>
> What's in your /etc/modprobe.conf?
>
> What does
>
> ifconfig eth0
>
> show? Particularly the second line?
>
> Jeremy R Schmidt writes:
>> Hello everyone.
>>
>> I have a 3com 3c905 network card, and it will not work with Fedora core
>> 2.
>> I can use it while doing a telnet install, it is recognized by linux, but
>> is not assigned a dhcp address by my router after linux is installed.
>> I have tried adding acpi=off in the grub configuration with no success.
>> Anyone have any ideas?
>>
>> Thanks.
>> _______________________________________________
>> Speakup mailing list
>> Speakup at braille.uwo.ca
>> http://speech.braille.uwo.ca/mailman/listinfo/speakup
>
> --
>
> Janina Sajka, Chair
> Accessibility Workgroup
> Free Standards Group (FSG)
>
> janina at freestandards.org Phone: +1 202.494.7040
>
>
> _______________________________________________
> Speakup mailing list
> Speakup at braille.uwo.ca
> http://speech.braille.uwo.ca/mailman/listinfo/speakup
>
>
