Where should I look for info on setting up dsl with linux? On the setup kit that came with my modem it says to instert the instalation cd and tell it your setting up a second computer which doesn't help much. The configuration I have for my isp uses PPPOA with a dinamic ip and it does have router capability. ----- Original Message ----- From: "Jacob Schmude" <jschmude@xxxxxxxxxxxx> To: "Speakup is a screen review system for Linux." <speakup at braille.uwo.ca> Sent: Monday, January 05, 2004 5:27 PM Subject: Re: broadband connectivity advice > -----BEGIN PGP SIGNED MESSAGE----- > Hash: SHA1 > > On Mon, 5 Jan 2004 18:44:20 -0500 (EST), Chuck Hallenbeck wrote: > >1. What part of the setup must be done by my provider, and what > >part by me? My provider advertises that they only support Windows > >and Mac OS, but that's what Verizon said too. > You hook the cable modem up in to your computer and your TV cable line, and your computer connects through it. However, activation is done on the > provider's end and you can't use it until they activate you, in the case of adelphia (my provider) they activate you based on the mac address of your cable > modem so even if you move you're still activated as long as you stay in the area where they provide service. > >>2. With DSL, I used the Roaring Penguin PPP-O-E scripts and > >configuring, starting, and stopping my connection was a snap. Is > >there any analogous tool for handling cable modem DHCP > >connections? > No, you don't need it. The cable modem will appear as a standard ethernet device if you plug it in via USB, and if you plug it in via ethernet, you just use it > through your NIC. Either way, only thing you need is standard network tools such as dhcpcd and ifconfig. In general, you don't "stop" a cable connection, > it's always on. > NOTE on USB connectivity: Linux supports cable modems based on the CDC standard, which most are. If yours is not, you may have to connect via > ethernet. This means, that if you already use your ethernet card for home networking, you're gonna need another NIC. If your modem isn't detected by the > hotplug subsystem, it may still be supported. Try loading the CDCEther module in 2.4 kernels, or the usbnet module in 2.6 kernels. The cable modem I use is > a motorola surfboard sb-5100, which works fine with USB, though it isn't acknowledged as being supported in the driver, the only slight quirk being that after > fedora's kudzu tool got done with it, it needed to be unplugged and reset--turning on safe probing in kudzu fixed that. Same applies if switching from a 2.4 to > a 2.6 kernel, cable modem needs a reset. > >3. I found lots of stuff to read about DSL, but precious little > >about cable modem in Linux. Anyone know something useful I can > >sink my teeth into? > There used to be a cable-modem howto at the LDP, I think it's still there. It's a bit dated (for instance it doesn't acknowledge that linux can use most USB > cable modems), but it may still be useful. In general there's precious little to read because all standard networking configuration applies, so there's really > nothing special that needs to be done in most cases. If it works with mac os x then it's a 99% chance that it works with linux as well, I've found this to be the > general rule for services and devices alike. > >My system is a Slackware 9.1 distro with lots of bells and > >whistles. But I have tasted a high speed connection and can > >hardly bear to use a 56K dialup ISP again. > Yeah, I know what ya mean. > > > -----BEGIN PGP SIGNATURE----- > Version: PGP SDK 3.0 > > iQA/AwUBP/oA1JXfgIVMPEIbEQJGvwCg1MMtghQFQVITZLWMqJFv73N5O+UAn1WE > DDtwERMogEYkHazokKNDu+Av > =Bvm1 > -----END PGP SIGNATURE----- > > > > _______________________________________________ > Speakup mailing list > Speakup at braille.uwo.ca > http://speech.braille.uwo.ca/mailman/listinfo/speakup
