Hello Igor, I'm not sure which distro you are using, but if you are using Debian, you just set up the interface definition as follows in /etc/network/interfaces: # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8) # The loopback interface auto lo iface lo inet loopback # The first network card - this entry was created during the Debian installation # (network, broadcast and gateway are optional) auto eth0 iface eth0 inet dhcp # end of setup. then as root type these commands: ifdown eth0 ifup eth0 At that point, pump should configure the interface and also create a /etc/resolv.conf. William On Tue, Mar 19, 2002 at 02:33:34PM -0500, Igor Gueths wrote: > Hi Victor. I have network access. There are two things that I don't have as of yet. 1 of them is Dns, and the other is I don't have it set to configure the interfaces with pump on start-up. Does anyone know how I could go about doing this? Thanks! > ----- Original Message ----- > From: Victor Tsaran <tsar at sylaba.poznan.pl> > To: <speakup at braille.uwo.ca> > Sent: Monday, March 18, 2002 9:15 PM > Subject: Re: question > > > > Hi, Igor! > > Loopback interface will work regardless of whether your physical network > > card working or not. Loopback interface, 127.0.0.1, is present in Linux by > > default. So your card is not working properly if it is not detected by > > ifconfig. > > Vic > > > > ----- Original Message ----- > > From: "Igor Gueths" <igueths at yahoo.com> > > To: <speakup at braille.uwo.ca> > > Sent: Tuesday, March 19, 2002 12:24 AM > > Subject: Re: question > > > > > > > Hi Victer. The card is actually recognized, and the > > > module seems to load fine. In fact, when I do > > > ifconfig, I get status messages. Something like this: > > > Loopback=127.0.0.1. Netmask=255.255.0.0. Mtu=16300. > > > Then it goes on to display packet stats. At least I > > > got an mtu reading that wasn't 0, so I believe that > > > this could indicate that the interface is functioning. > > > Is this so? By the way, to answer your question on the > > > SMC cards, I actually have a Linksys card that uses > > > the tulip module. > > > What I'm planning to do something like ifconfig eth0 > > > -dhcp to configure the interface based on dhcp. Also, > > > sorry for the long response time, its just that mail > > > over here was down for about two days, and its back > > > up. -I have also noticed an interesting atribute in > > > kernel 2.4.18. Every time -I press the del key, > > > dec-talk says numlock on. COuld this have to do with > > > an incorrect keymap being loaded at boot time? Thanks > > > in advance!- Victor Tsaran <tsar at sylaba.poznan.pl> > > > wrote: > > > > Hi, Igor! > > > > Is there a possibility that your netcard module > > > > conflicts with another > > > > module which kicks it out? Can you do a full "dmesg" > > > > trace and see what > > > > happens there? Also, if I remember correctly, > > > > tulip.o module was for SMC > > > > cards, right? If yes, then I think there was some > > > > update to that module last > > > > year. But that might not apply to you since you are > > > > using the newest kernel, > > > > is that so? > > > > Also, I think that your card might be recognized by > > > > the hardware detection > > > > tool, but the module itself does not load. Perhaps > > > > you should check your > > > > /etc/modules.conf or edit your /etc/rc.d/rc.local to > > > > have your module load > > > > at startup. > > > > Vic > > > > > > > > > > > > > > > > > > > > > > > > > > > > _______________________________________________ > > > > Speakup mailing list > > > > Speakup at braille.uwo.ca > > > > > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > > > > > > __________________________________________________ > > > Do You Yahoo!? > > > Yahoo! Sports - live college hoops coverage > > > http://sports.yahoo.com/ > > > > > > _______________________________________________ > > > Speakup mailing list > > > Speakup at braille.uwo.ca > > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > > > > > > > > > > > > > > > > > > > _______________________________________________ > > Speakup mailing list > > Speakup at braille.uwo.ca > > http://speech.braille.uwo.ca/mailman/listinfo/speakup > > > _________________________________________________________ > Do You Yahoo!? > Get your free @yahoo.com address at http://mail.yahoo.com > > > _______________________________________________ > Speakup mailing list > Speakup at braille.uwo.ca > http://speech.braille.uwo.ca/mailman/listinfo/speakup
