Changes in v4: * Cleanup the GPUCC code to keep only the clocks which would be requested from the GPU client SW. * Clean up of code as well as header file clock IDs. * Due to the above cleanup the patches to enable/disable clocks for GPU GDSC requirement is not supported : https://patchwork.kernel.org/patch/10563889/ * The GPU_GX RCG support is also removed from the main driver, so the corresponding RCG ops are removed : https://patchwork.kernel.org/patch/10563891/ Changes in v3: * Modified the determine_rate() op to use the min/max rate range to round the requested rate within the set_rate range. With this, requested set rate will always stay within the limits. Changes in v2: Addressed review comments given by Stephen: https://lkml.org/lkml/2018/6/6/294 * Introduce clk_rcg2_gfx3d_determine_rate ops to return the best parent as 'gpucc_pll0_even' and best parent rate as twice of the requested rate always. This will eliminate the need of frequency table as source and div-2 are fixed for gfx3d_clk_src. Also modified the clk_rcg2_set_rate ops to configure the fixed source and div. * Add support to check if requested rate falls within allowed set_rate range. This will not let the source gpucc_pll0 to go out of the supported range and also client can request the rate within the range. * Fixed comment text in probe function and added module description for GPUCC driver. The graphics clock driver depends upon the below change. https://lkml.org/lkml/2018/6/23/108 Changes in v1: This patch series adds support for graphics clock controller for SDM845. Below is the brief description for each change: 1. For some of the GDSCs, there is requirement to enable/disable the few clocks before turning on/off the gdsc power domain. This patch will add support to enable/disable the clock associated with the gdsc along with power domain on/off callbacks. 2. To turn on the gpu_gx_gdsc, there is a hardware requirement to turn on the root clock (GFX3D RCG) first which would be the turn on signal for the gdsc along with the SW_COLLAPSE. As per the current implementation of clk_rcg2_shared_ops, it clears the root_enable bit in the enable() clock ops. But due to the above said requirement for GFX3D shared RCG, root_enable bit would be already set by gdsc driver and rcg2_shared_ops should not clear the root unless the disable() is called. This patch add support for the same by reusing the existing clk_rcg2_shared_ops and deriving "clk_rcg2_gfx3d_ops" clk_ops for GFX3D clock to take care of the root set/clear requirement. 3. Add device tree bindings for graphics clock controller for SDM845. 4. Add graphics clock controller (GPUCC) driver for SDM845. [v1] : https://lore.kernel.org/patchwork/project/lkml/list/?series=348697 [v2] : https://lore.kernel.org/patchwork/project/lkml/list/?series=359012 Amit Nischal (2): dt-bindings: clock: Introduce QCOM Graphics clock bindings clk: qcom: Add graphics clock controller driver for SDM845 .../devicetree/bindings/clock/qcom,gpucc.txt | 18 ++ drivers/clk/qcom/Kconfig | 9 + drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/gpucc-sdm845.c | 231 +++++++++++++++++++++ include/dt-bindings/clock/qcom,gpucc-sdm845.h | 24 +++ 5 files changed, 283 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/qcom,gpucc.txt create mode 100644 drivers/clk/qcom/gpucc-sdm845.c create mode 100644 include/dt-bindings/clock/qcom,gpucc-sdm845.h -- Qualcomm INDIA, on behalf of Qualcomm Innovation Center, Inc.is a member of the Code Aurora Forum, hosted by the Linux Foundation.
