Re: [PATCH 04/12] i2c: qup: schedule EOT and FLUSH tags at the end of transfer

[Abhishek Sahu <absahu@xxxxxxxxxxxxxx>]

On 2018-02-15 20:01, Sricharan R wrote:
> Hi Abhishek,
>
> On 2/3/2018 1:28 PM, Abhishek Sahu wrote:
> > A single BAM transfer can have multiple read and write messages.
> > The EOT and FLUSH tags should be scheduled at the end of BAM HW
> > descriptors. Since the READ and WRITE can be present in any order
> > so for some of the cases, these tags are not being written
> > correctly.
> >
> > Signed-off-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
> > ---
> >  drivers/i2c/busses/i2c-qup.c | 54 
> > ++++++++++++++++++++------------------------
> >  1 file changed, 24 insertions(+), 30 deletions(-)
> >
> > diff --git a/drivers/i2c/busses/i2c-qup.c 
> > b/drivers/i2c/busses/i2c-qup.c
> > index bb83a2967..6357aff 100644
> > --- a/drivers/i2c/busses/i2c-qup.c
> > +++ b/drivers/i2c/busses/i2c-qup.c
> > @@ -560,7 +560,7 @@ static int qup_i2c_set_tags_smb(u16 addr, u8 
> > *tags, struct qup_i2c_dev *qup,
> >  }
> >
> >  static int qup_i2c_set_tags(u8 *tags, struct qup_i2c_dev *qup,
> > -			    struct i2c_msg *msg,  int is_dma)
> > +			    struct i2c_msg *msg)
> >  {
> >  	u16 addr = i2c_8bit_addr_from_msg(msg);
> >  	int len = 0;
> > @@ -601,11 +601,6 @@ static int qup_i2c_set_tags(u8 *tags, struct 
> > qup_i2c_dev *qup,
> >  	else
> >  		tags[len++] = data_len;
> >
> > -	if ((msg->flags & I2C_M_RD) && last && is_dma) {
> > -		tags[len++] = QUP_BAM_INPUT_EOT;
> > -		tags[len++] = QUP_BAM_FLUSH_STOP;
> > -	}
> > -
> >  	return len;
> >  }
> >
> > @@ -614,7 +609,7 @@ static int qup_i2c_issue_xfer_v2(struct 
> > qup_i2c_dev *qup, struct i2c_msg *msg)
> >  	int data_len = 0, tag_len, index;
> >  	int ret;
> >
> > -	tag_len = qup_i2c_set_tags(qup->blk.tags, qup, msg, 0);
> > +	tag_len = qup_i2c_set_tags(qup->blk.tags, qup, msg);
> >  	index = msg->len - qup->blk.data_len;
> >
> >  	/* only tags are written for read */
> > @@ -710,7 +705,7 @@ static int qup_i2c_bam_do_xfer(struct qup_i2c_dev 
> > *qup, struct i2c_msg *msg,
> >  			while (qup->blk.pos < blocks) {
> >  				tlen = (i == (blocks - 1)) ? rem : limit;
> >  				tags = &qup->start_tag.start[off + len];
> > -				len += qup_i2c_set_tags(tags, qup, msg, 1);
> > +				len += qup_i2c_set_tags(tags, qup, msg);
> >  				qup->blk.data_len -= tlen;
> >
> >  				/* scratch buf to read the start and len tags */
> > @@ -738,17 +733,11 @@ static int qup_i2c_bam_do_xfer(struct 
> > qup_i2c_dev *qup, struct i2c_msg *msg,
> >  				return ret;
> >
> >  			off += len;
> > -			/* scratch buf to read the BAM EOT and FLUSH tags */
> > -			ret = qup_sg_set_buf(&qup->brx.sg[rx_buf++],
> > -					     &qup->brx.tag.start[0],
> > -					     2, qup, DMA_FROM_DEVICE);
> > -			if (ret)
> > -				return ret;
> >  		} else {
> >  			while (qup->blk.pos < blocks) {
> >  				tlen = (i == (blocks - 1)) ? rem : limit;
> >  				tags = &qup->start_tag.start[off + tx_len];
> > -				len = qup_i2c_set_tags(tags, qup, msg, 1);
> > +				len = qup_i2c_set_tags(tags, qup, msg);
> >  				qup->blk.data_len -= tlen;
> >
> >  				ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++],
> > @@ -768,26 +757,31 @@ static int qup_i2c_bam_do_xfer(struct 
> > qup_i2c_dev *qup, struct i2c_msg *msg,
> >  			}
> >  			off += tx_len;
> >
> > -			if (idx == (num - 1)) {
> > -				len = 1;
> > -				if (rx_buf) {
> > -					qup->btx.tag.start[0] =
> > -							QUP_BAM_INPUT_EOT;
> > -					len++;
> > -				}
> > -				qup->btx.tag.start[len - 1] =
> > -							QUP_BAM_FLUSH_STOP;
> > -				ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++],
> > -						     &qup->btx.tag.start[0],
> > -						     len, qup, DMA_TO_DEVICE);
> > -				if (ret)
> > -					return ret;
> > -			}
> >  		}
> >  		idx++;
> >  		msg++;
> >  	}
>
>  While here, can you please split above the if, else in to two
> separate functions ?
>  and probably one more function for handling the NACK case down below.
> The function
>  size at the moment is too big.

 Sure. Already I split this function into 2 functions in
 [PATCH 09/12] i2c: qup: fix buffer overflow for multiple msg of maximum 
xfer len
 which is making function size smaller. I will check if I can split in 
more
 functions.

> > +	/* schedule the EOT and FLUSH I2C tags */
> > +	len = 1;
> > +	if (rx_buf) {
> > +		qup->btx.tag.start[0] = QUP_BAM_INPUT_EOT;
> > +		len++;
> > +
> > +		/* scratch buf to read the BAM EOT and FLUSH tags */
> > +		ret = qup_sg_set_buf(&qup->brx.sg[rx_buf++],
> > +				     &qup->brx.tag.start[0],
> > +				     2, qup, DMA_FROM_DEVICE);
> > +		if (ret)
> > +			return ret;
> > +	}
> > +
> > +	qup->btx.tag.start[len - 1] = QUP_BAM_FLUSH_STOP;
> > +	ret = qup_sg_set_buf(&qup->btx.sg[tx_buf++], &qup->btx.tag.start[0],
> > +			     len, qup, DMA_TO_DEVICE);
> > +	if (ret)
> > +		return ret;
> > +
>
>   May be you can change the commit to make it explicit to say what is 
> being
>   fixed, like "current code is broken when there is sequence of
> wr,rd,wr" like that.
>   Agree on this fix otherwise.

 Thanks. I will update the commit message to include the failure
 case which will give clear idea.

 Thanks,
 Abhishek
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html