On 2/3/2018 1:28 PM, Abhishek Sahu wrote:
> Currently the i2c error handling in BAM mode is not working
> properly in stress condition.
>
> 1. After an error, the FIFO are being written with FLUSH and
> EOT tags which should not be required since already these tags
> have been written in BAM descriptor itself.
>
> 2. QUP state is being moved to RESET in IRQ handler in case
> of error. When QUP HW encounters an error in BAM mode then it
> moves the QUP STATE to PAUSE state. In this case, I2C_FLUSH
> command needs to be executed while moving to RUN_STATE by writing
> to the QUP_STATE register with the I2C_FLUSH bit set to 1.
>
> 3. In Error case, sometimes, QUP generates more than one
> interrupt which will trigger the complete again. After an error,
> the flush operation will be scheduled after doing
> reinit_completion which should be triggered by BAM IRQ callback.
> If the second QUP IRQ comes during this time then it will call
> the complete and the transfer function will assume the all the
> BAM HW descriptors have been completed.
>
> 4. The release DMA is being called after each error which
> will free the DMA tx and rx channels. The error like NACK is very
> common in I2C transfer and every time this will be overhead. Now,
> since the error handling is proper so this release channel can be
> completely avoided.
>
> Signed-off-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
> ---
> drivers/i2c/busses/i2c-qup.c | 25 ++++++++++++++++---------
> 1 file changed, 16 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-qup.c b/drivers/i2c/busses/i2c-qup.c
> index 094be6a..6227a5c 100644
> --- a/drivers/i2c/busses/i2c-qup.c
> +++ b/drivers/i2c/busses/i2c-qup.c
> @@ -228,9 +228,24 @@ static irqreturn_t qup_i2c_interrupt(int irq, void *dev)
> if (bus_err)
> writel(bus_err, qup->base + QUP_I2C_STATUS);
>
> + /*
> + * Check for BAM mode and returns if already error has come for current
> + * transfer. In Error case, sometimes, QUP generates more than one
> + * interrupt.
> + */
> + if (qup->use_dma && (qup->qup_err || qup->bus_err))
> + return IRQ_HANDLED;
> +
> /* Reset the QUP State in case of error */
> if (qup_err || bus_err) {
> - writel(QUP_RESET_STATE, qup->base + QUP_STATE);
> + /*
> + * Don’t reset the QUP state in case of BAM mode. The BAM
> + * flush operation needs to be scheduled in transfer function
> + * which will clear the remaining schedule descriptors in BAM
> + * HW FIFO and generates the BAM interrupt.
> + */
> + if (!qup->use_dma)
> + writel(QUP_RESET_STATE, qup->base + QUP_STATE);
> goto done;
> }
>
> @@ -841,20 +856,12 @@ static int qup_i2c_bam_do_xfer(struct qup_i2c_dev *qup, struct i2c_msg *msg,
> goto desc_err;
> }
>
> - if (rx_buf)
> - writel(QUP_BAM_INPUT_EOT,
> - qup->base + QUP_OUT_FIFO_BASE);
> -
> - writel(QUP_BAM_FLUSH_STOP, qup->base + QUP_OUT_FIFO_BASE);
> -
> qup_i2c_flush(qup);
>
> /* wait for remaining interrupts to occur */
> if (!wait_for_completion_timeout(&qup->xfer, HZ))
> dev_err(qup->dev, "flush timed out\n");
>
> - qup_i2c_rel_dma(qup);
> -
> ret = (qup->bus_err & QUP_I2C_NACK_FLAG) ? -ENXIO : -EIO;
> }
>
>
Reviewed-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
Regards,
Sricharan
--
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
