On 2018-01-29 10:41, Sricharan R wrote:
Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts | 78
+++++++++++++++++++++++++
2 files changed, 79 insertions(+)
create mode 100644 arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index ef5b133..b4339ae 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -729,6 +729,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
qcom-ipq4019-ap.dk04.1-c5.dtb \
qcom-ipq4019-ap.dk04.1-c3.dtb \
qcom-ipq4019-ap.dk07.1-c1.dtb \
+ qcom-ipq4019-ap.dk07.1-c2.dtb \
qcom-ipq8064-ap148.dtb \
qcom-msm8660-surf.dtb \
qcom-msm8960-cdp.dtb \
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
new file mode 100644
index 0000000..d4ee52d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017, The Linux Foundation. All rights reserved.
+
+#include "qcom-ipq4019-ap.dk07.1.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. IPQ40xx/AP-DK07.1-C2";
s/IPQ40xx/IPQ4019
+
+ soc {
+ pcie0: pci@40000000 {
+ status = "disabled";
+ };
We can disable in base dtsi itself.
+
+ pinctrl@1000000 {
+ serial_1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ mux {
+ pins = "gpio13", "gpio14",
"gpio15";
+ function = "blsp_spi0";
+ bias-disable;
+ };
+ cs1 {
+ pins = "gpio12";
+ function = "gpio";
+ };
+ host_int1 {
+ pins = "gpio10";
+ function = "gpio";
+ input;
+ };
+ cs2 {
+ pins = "gpio45";
+ function = "gpio";
+ };
+ host_int2 {
+ pins = "gpio61";
+ function = "gpio";
+ input;
+ };
+ rst {
+ pins = "gpio36";
+ function = "gpio";
+ output-high;
+ };
Normally spi pins should contains spi protocol related pins
could you please explain what is the role of host_pin and rst
pins and which driver will use these.
+ };
+ };
+
+ serial@78b0000 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+ };
+
+ spi_0: spi@78b5000 { /* BLSP1 QUP1 */
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "ok";
From pinmux, it looks like multiple gpio based cs are being
used so do we need to specify cs-gpios like dk01-c2.
Thanks,
Abhishek
+
+ spidev0_0 {
+ compatible = "spidev";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ };
+ spidev0_1 {
+ compatible = "spidev";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+ };
+ };
+ };
+};
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
