Hi Rob,
On 12/26/2017 11:06 PM, Rob Herring wrote:
> On Thu, Dec 21, 2017 at 5:53 AM, Sricharan R <sricharan@xxxxxxxxxxxxxx> wrote:
>> Hi Rob,
>>
>> On 12/21/2017 2:48 AM, Rob Herring wrote:
>>> On Wed, Dec 20, 2017 at 11:55:33AM +0530, Sricharan R wrote:
>>>> Hi Viresh,
>>>>
>>>> On 12/20/2017 8:56 AM, Viresh Kumar wrote:
>>>>> On 19-12-17, 21:25, Sricharan R wrote:
>>>>>> + cpu@0 {
>>>>>> + compatible = "qcom,krait";
>>>>>> + enable-method = "qcom,kpss-acc-v1";
>>>>>> + device_type = "cpu";
>>>>>> + reg = <0>;
>>>>>> + qcom,acc = <&acc0>;
>>>>>> + qcom,saw = <&saw0>;
>>>>>> + clocks = <&kraitcc 0>;
>>>>>> + clock-names = "cpu";
>>>>>> + cpu-supply = <&smb208_s2a>;
>>>>>> + operating-points-v2 = <&cpu_opp_table>;
>>>>>> + };
>>>>>> +
>>>>>> + qcom,pvs {
>>>>>> + qcom,pvs-format-a;
>>>>>> + };
>>>>>
>>>>> Not sure what Rob is going to say on that :)
>>>>>
>>>>
>>>> Yes. Would be good to know the best way.
>>>
>>> Seems like this should be a property of an efuse node either implied by
>>> the compatible or a separate property. What determines format A vs. B?
>>>
>>
>> Yes, this efuse registers are part of the eeprom (qfprom) tied to the soc.
>> So this property (details like bitfields and register offsets that it represents)
>> can be put soc specific and nvmem apis can be used to read
>> the registers. Does something like below look ok ?
>>
>> qcom,pvs {
>> compatible = "qcom,pvs-ipq8064";
>> nvmem-cells = <&pvs_efuse>;
>> }
>
> Why do you need this node? It doesn't look like it corresponds to a
> h/w block. It looks like you are just creating it to instantiate a
> driver.
>
>> qfprom: qfprom@700000 {
>> compatible = "qcom,qfprom";
>
> Either this or...
>
>> reg = <0x00700000 0x1000>;
>> #address-cells = <1>;
>> #size-cells = <1>;
>> ranges;
>> pvs_efuse: pvs {
>
> a compatible here should be specific enough so the OS can know what
> the bits are.
Infact the above "qcom,pvs" node is required mainly to act as a consumer
for the nvmem data provider ("qcom,qfprom") (using nvmem-cells = <&pvs_efuse>)
Then "qfprom" can be made to contain a "format_a" or "format_b" specific cell.
So all that is needed is, nvmem-cells = <&pvs_efuse_phandle> needs to be available
somewhere. The requirement is similar what is now done by "operating-points-v2-ti-cpu"
and the ti-cpufreq.c. There "operating-points-v2-ti-cpu" node, contains the syscon
register to read the efuse values. Similarly does defining a new
"operating-points-v2-krait-cpu" which would contain the nvmem-cells property look ok ?
This would avoid defining a new qcom,pvs node.
cpu@0 {
compatible = "qcom,krait";
enable-method = "qcom,kpss-acc-v1";
device_type = "cpu";
reg = <0>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
clocks = <&kraitcc 0>;
clock-names = "cpu";
cpu-supply = <&smb208_s2a>;
operating-points-v2 = <&cpu_opp_table>;
};
cpu_opp_table: opp_table {
compatible = "operating-points-v2-krait-cpu";
nvmem-cells = <&pvs_efuse_format_a>;
/*
* Missing opp-shared property means CPUs switch DVFS states
* independently.
*/
opp-1400000000 {
opp-hz = /bits/ 64 <1400000000>;
opp-microvolt-speed0-pvs0-v0 = <1250000>;
opp-microvolt-speed0-pvs1-v0 = <1175000>;
opp-microvolt-speed0-pvs2-v0 = <1125000>;
opp-microvolt-speed0-pvs3-v0 = <1050000>;
};
...
}
qfprom: qfprom@700000 {
compatible = "qcom,qfprom";
reg = <0x00700000 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
pvs_efuse_format_a: pvs {
reg = <0xc0 0x8>;
};
}
Regards,
Sricharan
--
"QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
