On Sun, Aug 13, 2017 at 12:42:59PM +0300, Leonid Segal wrote:
> Add initial device tree support for Variscite DART-SD410 Evalueation board.
> This board is also known as VAR-SD410CustomBoard.
>
> Signed-off-by: Leonid Segal <leonid.s@xxxxxxxxxxxxx>
> ---
A few comments, mainly about your documentation on the Variscite
website. Specifically the schematics. Please tell your hardware
people to be consistent in your naming conventions for pins.
MPP_GPIO/PM_GPIO appear to be interchangeable. And it's usually
best to split out the PMIC pins from the non-pmic. That's my 2
cents at least.
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../boot/dts/qcom/apq8016-var-dart-pmic-pins.dtsi | 53 +++
> .../boot/dts/qcom/apq8016-var-dart-soc-pins.dtsi | 88 ++++
> arch/arm64/boot/dts/qcom/apq8016-var-dart.dts | 21 +
> arch/arm64/boot/dts/qcom/apq8016-var-dart.dtsi | 525
<snip>
> + pins = "gpio32";
> + };
> + pinconf {
> + pins = "gpio32";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + msm_key_volp_n_default: msm_key_volp_n_default {
Schematics show this to be a Home button. If so this needs to be
updated to reflect that.
> + pinmux {
> + function = "gpio";
> + pins = "gpio107";
> + };
> + pinconf {
> + pins = "gpio107";
> + drive-strength = <8>;
> + input-enable;
> + bias-pull-up;
> + };
> + };
> +};
> diff --git a/arch/arm64/boot/dts/qcom/apq8016-var-dart.dts
<snip>
> +/dts-v1/;
> +
> +#include "apq8016-var-dart.dtsi"
> +
> +/ {
> + model = "Variscite LTD. VAR-DART410";
> + compatible = "qcom,apq8016-dart", "qcom,apq8016", "qcom,dart";
qcom isnt making this board. Please use something like "variscite,dart",
"qcom,apq8016"
> +};
> diff --git a/arch/arm64/boot/dts/qcom/apq8016-var-dart.dtsi
> b/arch/arm64/boot/dts/qcom/apq8016-var-dart.dtsi
> new file mode 100644
> index 000000000000..f214d0b101a4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/apq8016-var-dart.dtsi
<snip>
> +
> + usb@78d9000 {
> + extcon = <&usb_id>, <&usb_id>;
> + status = "okay";
> + };
> +
> + ehci@78d9000 {
> + status = "okay";
Can you try removing the echi and using the chipidea instead. Take a
look at the current db410c in -next. Try it out and see if that works
for you. If it does, modify your nodes to match up.
> + };
> +
> + phy@78d9000 {
> + v1p8-supply = <&pm8916_l7>;
> + v3p3-supply = <&pm8916_l13>;
> + vddcx-supply = <&pm8916_s1>;
> + extcon = <&usb_id>, <&usb_id>;
> + dr_mode = "otg";
> + status = "okay";
> + switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&usb_sw_sel_pm>;
Same here, I think some things changed here. Need to update.
switch-gpio went away.
> + };
> +
> + lpass@07708000 {
> + status = "okay";
> + };
> +
<snip>
Regards,
Andy Gross
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
