On Thu, Jun 29, 2017 at 07:47:41PM +0530, Sricharan R wrote:
> IPQ8074 has an integrated Q6V5 Hexagon dsp - Lithium Wlan (WCSS) core.
> This patch adds the required bindings to load, boot, shutdown that
> remoteproc subsystem.
>
> Signed-off-by: Sricharan R <sricharan@xxxxxxxxxxxxxx>
> ---
> .../bindings/remoteproc/qcom,q6v5-wcss.txt | 139 +++++++++++++++++++++
> 1 file changed, 139 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,q6v5-wcss.txt
>
> diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5-wcss.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5-wcss.txt
> new file mode 100644
> index 0000000..f664c26
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5-wcss.txt
> @@ -0,0 +1,139 @@
> +Qualcomm Hexagon (Q6) - WCSS Peripheral Image Loader
> +
> +This document defines the binding for a component that loads and boots firmware
> +on the integrated Qualcomm Hexagon - WCSS core.
> +
> +- compatible:
> + Usage: required
> + Value type: <string>
> + Definition: must be one of:
> + "qcom,q6v5-wcss-pil",
> +- reg:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: must specify the base address and size of the qdsp6 and
> + mpm (msm power manager) register blocks.
> +
> +- reg-names:
> + Usage: required
> + Value type: <stringlist>
> + Definition: must be "q6" and "mpm"
> +
> +- interrupts-extended:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: must list the watchdog, fatal IRQs ready, handover and
fatal, ready, ...
> + stop-ack IRQs
> +
> +- interrupt-names:
> + Usage: required
> + Value type: <stringlist>
> + Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack"
> +
> +- clocks:
> + Usage: required
> + Value type: <phandle>
These are not just a phandle.
> + Definition: references to the axim-q6, axim2-q6, axi-wcss,
> + ahb-q6, ahbs-q6, ahb-wcss, ahbs-wcss, sysnoc and mem.
> + to be held on behalf of the booting of the Hexagon and WCSS
> + core. These are the interface, bus, mem clocks required for
> + the Q6 and WCSS cores.
> +
> +- clock-names:
> + Usage: required
> + Value type: <stringlist>
> + Definition: must be "axim-q6", "axim2-q6", "axi-wcss", "ahb-q6",
> + "ahbs-q6", "ahb-wcss", "ahbs-wcss", "sysnoc", "mem"
> +
> +- resets:
> + Usage: required
> + Value type: <phandle>
> + Definition: reference to the reset-controller for the Q6-WCSS sub-system
This should be a list of 3 resets.
> +
> +- reset-names:
> + Usage: required
> + Value type: <stringlist>
> + Definition: must be "wcss_aon_reset", "wcss_reset", "wcss_q6_reset"
> +
> +- qcom,smem-states:
> + Usage: required
> + Value type: <phandle>
> + Definition: reference to the smem state for requesting the Hexagon to
> + shut down
> +
> +- qcom,smem-state-names:
> + Usage: required
> + Value type: <stringlist>
> + Definition: must be "stop"
> +
> +- qcom,halt-regs:
> + Usage: required
> + Value type: <prop-encoded-array>
> + Definition: a phandle reference to a syscon representing TCSR followed
> + by the three offsets within syscon for q6, wcss and tcsr global
> + halt registers.
> +
> += SUBNODES:
> +The Hexagon node must contain a subnode, named "q6" representing
> +the memory region used by the Hexagon firmware. The sub-node must contain:
Why does this need a sub-node?
> +
> +- memory-region:
> + Usage: required
> + Value type: <phandle>
> + Definition: reference to the reserved-memory for the Q6 firmware region
> +
> += EXAMPLE
> +The following example describes the resources needed to boot control the
> +Hexagon, as it is found on IPQ8074 boards.
> +
> + q6v5_wcss: q6v5_wcss@CD00000 {
s/_/-/ in the node name.
> + compatible = "q6v5-wcss-pil";
> + reg = <0xCD00000 0x4040>,
> + <0x4ab000 0x20>;
> + reg-names = "q6",
> + "mpm";
> + interrupts-extended = <&intc 0 325 1>,
> + <&wcss_smp2p_in 0 0>,
> + <&wcss_smp2p_in 1 0>,
> + <&wcss_smp2p_in 3 0>;
> + interrupt-names = "wdog",
> + "fatal",
> + "handover",
> + "stop-ack";
> + clocks = <&gcc GCC_SYS_NOC_WCSS_AHB_CLK>,
> + <&gcc GCC_WCSS_AHB_S_CLK>,
> + <&gcc GCC_WCSS_ECAHB_CLK>,
> + <&gcc GCC_Q6_AHB_CLK>,
> + <&gcc GCC_Q6_AHB_S_CLK>,
> + <&gcc GCC_WCSS_AXI_M_CLK>,
> + <&gcc GCC_MEM_NOC_Q6_AXI_CLK>,
> + <&gcc GCC_Q6_AXIM_CLK>,
> + <&gcc GCC_Q6_AXIM2_CLK>;
> + clock-names = "sysnoc",
> + "ahb-wcss",
> + "ahbs-wcss",
> + "ahb-q6",
> + "ahbs-q6",
> + "axi-wcss",
> + "memnoc",
> + "axim-q6",
> + "axim2-q6";
> +
> + resets = <&gcc GCC_WCSSAON_RESET>,
> + <&gcc GCC_WCSS_BCR>,
> + <&gcc GCC_WCSS_Q6_BCR>;
> +
> + reset-names = "wcss_aon_reset",
> + "wcss_reset",
> + "wcss_q6_reset";
> +
> + qcom,halt-regs = <&tcsr_mutex_block 0x0 0xA000 0xD000>;
> +
> + qcom,smem-states = <&wcss_smp2p_out 0>,
> + <&wcss_smp2p_out 1>;
> + qcom,smem-state-names = "shutdown",
> + "stop";
> + q6 {
> + memory-region = <&q6_region>;
> + };
> + };
> --
> QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
>
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
