On 02/05/17 11:08, Leo Yan wrote:
> Coresight includes debug module and usually the module connects with CPU
> debug logic. ARMv8 architecture reference manual (ARM DDI 0487A.k) has
> description for related info in "Part H: External Debug".
>
> Chapter H7 "The Sample-based Profiling Extension" introduces several
> sampling registers, e.g. we can check program counter value with
> combined CPU exception level, secure state, etc. So this is helpful for
> analysis CPU lockup scenarios, e.g. if one CPU has run into infinite
> loop with IRQ disabled. In this case the CPU cannot switch context and
> handle any interrupt (including IPIs), as the result it cannot handle
> SMP call for stack dump.
>
> This patch is to enable coresight debug module, so firstly this driver
> is to bind apb clock for debug module and this is to ensure the debug
> module can be accessed from program or external debugger. And the driver
> uses sample-based registers for debug purpose, e.g. when system triggers
> panic, the driver will dump program counter and combined context
> registers (EDCIDSR, EDVIDSR); by parsing context registers so can
> quickly get to know CPU secure state, exception level, etc.
>
> Some of the debug module registers are located in CPU power domain, so
> this requires the CPU power domain stays on when access related debug
> registers, but the power management for CPU power domain is quite
> dependent on SoC integration for power management. For the platforms
> which with sane power controller implementations, this driver follows
> the method to set EDPRCR to try to pull the CPU out of low power state
> and then set 'no power down request' bit so the CPU has no chance to
> lose power.
>
> If the SoC has not followed up this design well for power management
> controller, the user should use the command line parameter or sysfs
> to constrain all or partial idle states to ensure the CPU power
> domain is enabled and access coresight CPU debug component safely.
>
> Signed-off-by: Leo Yan <leo.yan@xxxxxxxxxx>
> ---
> drivers/hwtracing/coresight/Kconfig | 14 +
> drivers/hwtracing/coresight/Makefile | 1 +
> drivers/hwtracing/coresight/coresight-cpu-debug.c | 670 ++++++++++++++++++++++
> 3 files changed, 685 insertions(+)
> create mode 100644 drivers/hwtracing/coresight/coresight-cpu-debug.c
>
> diff --git a/drivers/hwtracing/coresight/Kconfig b/drivers/hwtracing/coresight/Kconfig
> index 130cb21..8d55d6d 100644
> --- a/drivers/hwtracing/coresight/Kconfig
> +++ b/drivers/hwtracing/coresight/Kconfig
> @@ -89,4 +89,18 @@ config CORESIGHT_STM
> logging useful software events or data coming from various entities
> in the system, possibly running different OSs
>
> +config CORESIGHT_CPU_DEBUG
> + tristate "CoreSight CPU Debug driver"
> + depends on ARM || ARM64
> + depends on DEBUG_FS
> + help
> + This driver provides support for coresight debugging module. This
> + is primarily used to dump sample-based profiling registers when
> + system triggers panic, the driver will parse context registers so
> + can quickly get to know program counter (PC), secure state,
> + exception level, etc. Before use debugging functionality, platform
> + needs to ensure the clock domain and power domain are enabled
> + properly, please refer Documentation/trace/coresight-cpu-debug.txt
> + for detailed description and the example for usage.
> +
> endif
> diff --git a/drivers/hwtracing/coresight/Makefile b/drivers/hwtracing/coresight/Makefile
> index af480d9..433d590 100644
> --- a/drivers/hwtracing/coresight/Makefile
> +++ b/drivers/hwtracing/coresight/Makefile
> @@ -16,3 +16,4 @@ obj-$(CONFIG_CORESIGHT_SOURCE_ETM4X) += coresight-etm4x.o \
> coresight-etm4x-sysfs.o
> obj-$(CONFIG_CORESIGHT_QCOM_REPLICATOR) += coresight-replicator-qcom.o
> obj-$(CONFIG_CORESIGHT_STM) += coresight-stm.o
> +obj-$(CONFIG_CORESIGHT_CPU_DEBUG) += coresight-cpu-debug.o
> diff --git a/drivers/hwtracing/coresight/coresight-cpu-debug.c b/drivers/hwtracing/coresight/coresight-cpu-debug.c
> new file mode 100644
> index 0000000..b77456d
> --- /dev/null
> +++ b/drivers/hwtracing/coresight/coresight-cpu-debug.c
[...]
> +static int debug_probe(struct amba_device *adev, const struct amba_id *id)
> +{
> + void __iomem *base;
> + struct device *dev = &adev->dev;
> + struct debug_drvdata *drvdata;
> + struct resource *res = &adev->res;
> + struct device_node *np = adev->dev.of_node;
> + int ret;
> +
> + drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL);
> + if (!drvdata)
> + return -ENOMEM;
> +
> + drvdata->cpu = np ? of_coresight_get_cpu(np) : 0;
> + if (per_cpu(debug_drvdata, drvdata->cpu)) {
> + dev_err(dev, "CPU%d drvdata has been initialized, "
> + "may be caused by binding wrong CPU node in the DT\n",
> + drvdata->cpu);
> + return -EBUSY;
> + }
> +
> + drvdata->dev = &adev->dev;
> + amba_set_drvdata(adev, drvdata);
> +
> + /* Validity for the resource is already checked by the AMBA core */
> + base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(base))
> + return PTR_ERR(base);
> +
> + drvdata->base = base;
> +
> + get_online_cpus();
> + per_cpu(debug_drvdata, drvdata->cpu) = drvdata;
> + ret = smp_call_function_single(drvdata->cpu, debug_init_arch_data,
> + drvdata, 1);
> + put_online_cpus();
> +
> + if (ret) {
> + dev_err(dev, "CPU%d debug arch init failed\n", drvdata->cpu);
> + goto err;
> + }
> +
> + if (!drvdata->edpcsr_present) {
> + dev_err(dev, "CPU%d sample-based profiling isn't implemented\n",
> + drvdata->cpu);
> + ret = -ENXIO;
> + goto err;
> + }
> +
> + if (!debug_count++) {
> + ret = debug_func_init();
> + if (ret)
> + goto err_func_init;
> + }
> +
> + mutex_lock(&debug_lock);
> + if (!debug_enable)
> + pm_runtime_put(dev);
> + mutex_unlock(&debug_lock);
> +
Just curious as why this is not registered under coresight bus using
coresight_register ? It would be good to group all the coresight devices
under that bus if possible.
--
Regards,
Sudeep
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
