On Mon 09 Jan 07:00 PST 2017, Imran Khan wrote:
> diff --git a/drivers/pinctrl/qcom/pinctrl-msm8998.c b/drivers/pinctrl/qcom/pinctrl-msm8998.c
[..]
> +
> +#define NORTH 0x500000
> +#define WEST 0x100000
> +#define EAST 0x900000
So the control registers are now laid out in 3 non-contiguous ranges?
Please move them to the top of the file.
> +#define REG_SIZE 0x1000
Just inline 0x1000 in the macro below.
> +#define PINGROUP(id, base, f1, f2, f3, f4, f5, f6, f7, f8, f9) \
> + { \
> + .name = "gpio" #id, \
> + .pins = gpio##id##_pins, \
> + .npins = (unsigned int)ARRAY_SIZE(gpio##id##_pins), \
> + .funcs = (int[]){ \
> + msm_mux_gpio, /* gpio mode */ \
> + msm_mux_##f1, \
> + msm_mux_##f2, \
> + msm_mux_##f3, \
> + msm_mux_##f4, \
> + msm_mux_##f5, \
> + msm_mux_##f6, \
> + msm_mux_##f7, \
> + msm_mux_##f8, \
> + msm_mux_##f9 \
> + }, \
> + .nfuncs = 10, \
> + .ctl_reg = base + REG_SIZE * id, \
> + .io_reg = base + 0x4 + REG_SIZE * id, \
> + .intr_cfg_reg = base + 0x8 + REG_SIZE * id, \
> + .intr_status_reg = base + 0xc + REG_SIZE * id, \
> + .intr_target_reg = base + 0x8 + REG_SIZE * id, \
> + .mux_bit = 2, \
> + .pull_bit = 0, \
> + .drv_bit = 6, \
> + .oe_bit = 9, \
> + .in_bit = 0, \
> + .out_bit = 1, \
> + .intr_enable_bit = 0, \
> + .intr_status_bit = 0, \
> + .intr_target_bit = 5, \
> + .intr_target_kpss_val = 3, \
> + .intr_raw_status_bit = 4, \
> + .intr_polarity_bit = 1, \
> + .intr_detection_bit = 2, \
> + .intr_detection_width = 2, \
> + }
> +
> +#define SDC_QDSD_PINGROUP(pg_name, ctl, pull, drv) \
> + { \
> + .name = #pg_name, \
> + .pins = pg_name##_pins, \
> + .npins = (unsigned int)ARRAY_SIZE(pg_name##_pins), \
> + .ctl_reg = ctl, \
> + .io_reg = 0, \
> + .intr_cfg_reg = 0, \
> + .intr_status_reg = 0, \
> + .intr_target_reg = 0, \
> + .mux_bit = -1, \
> + .pull_bit = pull, \
> + .drv_bit = drv, \
> + .oe_bit = -1, \
> + .in_bit = -1, \
> + .out_bit = -1, \
> + .intr_enable_bit = -1, \
> + .intr_status_bit = -1, \
> + .intr_target_bit = -1, \
> + .intr_raw_status_bit = -1, \
> + .intr_polarity_bit = -1, \
> + .intr_detection_bit = -1, \
> + .intr_detection_width = -1, \
> + }
> +
> +#define UFS_RESET(pg_name, offset) \
> + { \
> + .name = #pg_name, \
> + .pins = pg_name##_pins, \
> + .npins = (unsigned int)ARRAY_SIZE(pg_name##_pins), \
> + .ctl_reg = offset, \
> + .io_reg = offset + 0x4, \
> + .intr_cfg_reg = 0, \
> + .intr_status_reg = 0, \
> + .intr_target_reg = 0, \
> + .mux_bit = -1, \
> + .pull_bit = 3, \
> + .drv_bit = 0, \
> + .oe_bit = -1, \
> + .in_bit = -1, \
> + .out_bit = 0, \
> + .intr_enable_bit = -1, \
> + .intr_status_bit = -1, \
> + .intr_target_bit = -1, \
> + .intr_raw_status_bit = -1, \
> + .intr_polarity_bit = -1, \
> + .intr_detection_bit = -1, \
> + .intr_detection_width = -1, \
> + }
Please add an empty line here.
> +static const struct pinctrl_pin_desc msm8998_pins[] = {
[..]
> +enum msm8998_functions {
[..]
> + msm_mux_phase_flag6,
> + msm_mux_phase_flag29,
> + msm_mux_phase_flag30,
> + msm_mux_phase_flag31,
With the Qualcomm pinctrl driver it's possible to specify configuration
in DT for a subset of pins of a group. So I think you should squash the
"phase_flag"s and "atest_char" into one group each.
> + msm_mux_pa_indicator,
> + msm_mux_ssbi1,
> + msm_mux_isense_dbg,
> + msm_mux_mss_lte,
> + msm_mux_gpio,
> + msm_mux_NA,
> +};
[..]
> +static const struct msm_pingroup msm8998_groups[] = {
> + PINGROUP(0, EAST, blsp_spi1, blsp_uart1_a, blsp_uim1_a, NA, NA, NA, NA,
> + NA, NA),
Please do ignore the 80-char "rule" and skip the line break on
these - it makes the table easier to read.
[..]
> +};
> +
> +static const struct msm_pinctrl_soc_data msm8998_pinctrl = {
> + .pins = msm8998_pins,
> + .npins = ARRAY_SIZE(msm8998_pins),
> + .functions = msm8998_functions,
> + .nfunctions = ARRAY_SIZE(msm8998_functions),
> + .groups = msm8998_groups,
> + .ngroups = ARRAY_SIZE(msm8998_groups),
> + .ngpios = 153,
ngpios is 150
> +};
> +
Regards,
Bjorn
--
To unsubscribe from this list: send the line "unsubscribe linux-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
