AXS10X boards manages it's clocks using various PLLs. These PLL has same
dividers and corresponding control registers mapped to different addresses.
So we add one common driver for such PLLs.
Each PLL on AXS10X board consist of three dividers: IDIV, FBDIV and
ODIV. Output clock value is managed using these dividers.
We add pre-defined tables with supported rate values and appropriate
configurations of IDIV, FBDIV and ODIV for each value.
As of today we add support for PLLs that generate clock for the
following devices:
* ARC core on AXC CPU tiles.
* ARC PGU on ARC SDP Mainboard.
and more to come later.
Acked-by: Rob Herring <robh at kernel.org>
Signed-off-by: Vlad Zakharov <vzakhar at synopsys.com>
Signed-off-by: Jose Abreu <joabreu at synopsys.com>
Cc: Michael Turquette <mturquette at baylibre.com>
Cc: Stephen Boyd <sboyd at codeaurora.org>
Cc: Mark Rutland <mark.rutland at arm.com>
---
Changes v2..v3
- replaced complex data structures with simple cfg tables
- replaced non-hw based provider and clk registration functions with hw-based
- fixed typos and minor code styling issues
.../devicetree/bindings/clock/snps,pll-clock.txt | 28 ++
MAINTAINERS | 6 +
drivers/clk/axs10x/Makefile | 1 +
drivers/clk/axs10x/pll_clock.c | 334 +++++++++++++++++++++
4 files changed, 369 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/snps,pll-clock.txt
create mode 100644 drivers/clk/axs10x/pll_clock.c
diff --git a/Documentation/devicetree/bindings/clock/snps,pll-clock.txt b/Documentation/devicetree/bindings/clock/snps,pll-clock.txt
new file mode 100644
index 0000000..5706246
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/snps,pll-clock.txt
@@ -0,0 +1,28 @@
+Binding for the AXS10X Generic PLL clock
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible: should be "snps,axs10x-<name>-pll-clock"
+ "snps,axs10x-arc-pll-clock"
+ "snps,axs10x-pgu-pll-clock"
+- reg: should always contain 2 pairs address - length: first for PLL config
+registers and second for corresponding LOCK CGU register.
+- clocks: shall be the input parent clock phandle for the PLL.
+- #clock-cells: from common clock binding; Should always be set to 0.
+
+Example:
+ input-clk: input-clk {
+ clock-frequency = <33333333>;
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ };
+
+ core-clk: core-clk at 80 {
+ compatible = "snps,axs10x-arc-pll-clock";
+ reg = <0x80 0x10 0x100 0x10>;
+ #clock-cells = <0>;
+ clocks = <&input-clk>;
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 676c139..6f5c690 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -12133,6 +12133,12 @@ F: arch/arc/plat-axs10x
F: arch/arc/boot/dts/ax*
F: Documentation/devicetree/bindings/arc/axs10*
+SYNOPSYS ARC SDP clock driver
+M: Vlad Zakharov <vzakhar at synopsys.com>
+S: Supported
+F: drivers/clk/axs10x/*
+F: Documentation/devicetree/bindings/clock/snps,pll-clock.txt
+
SYSTEM CONFIGURATION (SYSCON)
M: Lee Jones <lee.jones at linaro.org>
M: Arnd Bergmann <arnd at arndb.de>
diff --git a/drivers/clk/axs10x/Makefile b/drivers/clk/axs10x/Makefile
index 01996b8..d747dea 100644
--- a/drivers/clk/axs10x/Makefile
+++ b/drivers/clk/axs10x/Makefile
@@ -1 +1,2 @@
obj-y += i2s_pll_clock.o
+obj-y += pll_clock.o
diff --git a/drivers/clk/axs10x/pll_clock.c b/drivers/clk/axs10x/pll_clock.c
new file mode 100644
index 0000000..e242df0
--- /dev/null
+++ b/drivers/clk/axs10x/pll_clock.c
@@ -0,0 +1,334 @@
+/*
+ * Synopsys AXS10X SDP Generic PLL clock driver
+ *
+ * Copyright (C) 2017 Synopsys
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/module.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/device.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+
+/* PLL registers addresses */
+#define PLL_REG_IDIV 0x0
+#define PLL_REG_FBDIV 0x4
+#define PLL_REG_ODIV 0x8
+
+/*
+ * Bit fields of the PLL IDIV/FBDIV/ODIV registers:
+ * ________________________________________________________________________
+ * |31 15| 14 | 13 | 12 |11 6|5 0|
+ * |-------RESRVED------|-NOUPDATE-|-BYPASS-|-EDGE-|--HIGHTIME--|--LOWTIME--|
+ * |____________________|__________|________|______|____________|___________|
+ *
+ * Following macros determine the way of access to these registers
+ * They should be set up only using the macros.
+ * reg should be an u32 variable.
+ */
+
+#define PLL_REG_GET_LOW(reg) \
+ (((reg) & (0x3F << 0)) >> 0)
+#define PLL_REG_GET_HIGH(reg) \
+ (((reg) & (0x3F << 6)) >> 6)
+#define PLL_REG_GET_EDGE(reg) \
+ (((reg) & (BIT(12))) ? 1 : 0)
+#define PLL_REG_GET_BYPASS(reg) \
+ (((reg) & (BIT(13))) ? 1 : 0)
+#define PLL_REG_GET_NOUPD(reg) \
+ (((reg) & (BIT(14))) ? 1 : 0)
+#define PLL_REG_GET_PAD(reg) \
+ (((reg) & (0x1FFFF << 15)) >> 15)
+
+#define PLL_REG_SET_LOW(reg, value) \
+ { reg |= (((value) & 0x3F) << 0); }
+#define PLL_REG_SET_HIGH(reg, value) \
+ { reg |= (((value) & 0x3F) << 6); }
+#define PLL_REG_SET_EDGE(reg, value) \
+ { reg |= (((value) & 0x01) << 12); }
+#define PLL_REG_SET_BYPASS(reg, value) \
+ { reg |= (((value) & 0x01) << 13); }
+#define PLL_REG_SET_NOUPD(reg, value) \
+ { reg |= (((value) & 0x01) << 14); }
+#define PLL_REG_SET_PAD(reg, value) \
+ { reg |= (((value) & 0x1FFFF) << 15); }
+
+#define PLL_LOCK BIT(0)
+#define PLL_ERROR BIT(1)
+#define PLL_MAX_LOCK_TIME 100 /* 100 us */
+
+struct pll_cfg {
+ u32 rate;
+ u32 idiv;
+ u32 fbdiv;
+ u32 odiv;
+};
+
+static const struct pll_cfg arc_pll_cfg[] = {
+ { 33333333, 1, 1, 1 },
+ { 50000000, 1, 30, 20 },
+ { 75000000, 2, 45, 10 },
+ { 90000000, 2, 54, 10 },
+ { 100000000, 1, 30, 10 },
+ { 125000000, 2, 45, 6 },
+ {},
+};
+
+static const struct pll_cfg pgu_pll_cfg[] = {
+ { 25200000, 1, 84, 90 },
+ { 50000000, 1, 100, 54 },
+ { 74250000, 1, 44, 16 },
+ {},
+};
+
+struct pll_clk {
+ struct clk_hw hw;
+ void __iomem *base;
+ void __iomem *lock;
+ const struct pll_cfg *pll_cfg;
+ struct device *dev;
+};
+
+static inline void pll_write(struct pll_clk *clk, unsigned int reg,
+ unsigned int val)
+{
+ iowrite32(val, clk->base + reg);
+}
+
+static inline u32 pll_read(struct pll_clk *clk, unsigned int reg)
+{
+ return ioread32(clk->base + reg);
+}
+
+static inline struct pll_clk *to_pll_clk(struct clk_hw *hw)
+{
+ return container_of(hw, struct pll_clk, hw);
+}
+
+static inline u32 div_get_value(unsigned int reg)
+{
+ if (PLL_REG_GET_BYPASS(reg))
+ return 1;
+
+ return PLL_REG_GET_HIGH(reg) + PLL_REG_GET_LOW(reg);
+}
+
+static inline u32 encode_div(unsigned int id, int upd)
+{
+ u32 div = 0;
+
+ PLL_REG_SET_LOW(div, (id%2 == 0) ? id >> 1 : (id >> 1) + 1);
+ PLL_REG_SET_HIGH(div, id >> 1);
+ PLL_REG_SET_EDGE(div, id%2);
+ PLL_REG_SET_BYPASS(div, id == 1 ? 1 : 0);
+ PLL_REG_SET_NOUPD(div, !upd);
+
+ return div;
+}
+
+static unsigned long pll_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+{
+ u64 rate;
+ u32 idiv, fbdiv, odiv;
+ struct pll_clk *clk = to_pll_clk(hw);
+
+ idiv = div_get_value(pll_read(clk, PLL_REG_IDIV));
+ fbdiv = div_get_value(pll_read(clk, PLL_REG_FBDIV));
+ odiv = div_get_value(pll_read(clk, PLL_REG_ODIV));
+
+ rate = (u64)parent_rate * fbdiv;
+ do_div(rate, idiv * odiv);
+
+ return rate;
+}
+
+static long pll_round_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long *prate)
+{
+ int i;
+ long best_rate;
+ struct pll_clk *clk = to_pll_clk(hw);
+ const struct pll_cfg *pll_cfg = clk->pll_cfg;
+
+ if (pll_cfg[0].rate == 0)
+ return -EINVAL;
+
+ best_rate = pll_cfg[0].rate;
+
+ for (i = 1; pll_cfg[i].rate != 0; i++) {
+ if (abs(rate - pll_cfg[i].rate) < abs(rate - best_rate))
+ best_rate = pll_cfg[i].rate;
+ }
+
+ return best_rate;
+}
+
+static int pll_set_rate(struct clk_hw *hw, unsigned long rate,
+ unsigned long parent_rate)
+{
+ int i;
+ struct pll_clk *clk = to_pll_clk(hw);
+ const struct pll_cfg *pll_cfg = clk->pll_cfg;
+
+ for (i = 0; pll_cfg[i].rate != 0; i++) {
+ if (pll_cfg[i].rate == rate) {
+ pll_write(clk, PLL_REG_IDIV,
+ encode_div(pll_cfg[i].idiv, 0));
+ pll_write(clk, PLL_REG_FBDIV,
+ encode_div(pll_cfg[i].fbdiv, 0));
+ pll_write(clk, PLL_REG_ODIV,
+ encode_div(pll_cfg[i].odiv, 1));
+
+ /*
+ * Wait until CGU relocks and check error status.
+ * If after timeout CGU is unlocked yet return error
+ */
+ udelay(PLL_MAX_LOCK_TIME);
+ if (!(ioread32(clk->lock) & PLL_LOCK))
+ return -ETIMEDOUT;
+
+ if (ioread32(clk->lock) & PLL_ERROR)
+ return -EINVAL;
+
+ return 0;
+ }
+ }
+
+ dev_err(clk->dev, "invalid rate=%ld, parent_rate=%ld\n", rate,
+ parent_rate);
+ return -EINVAL;
+}
+
+static const struct clk_ops pll_ops = {
+ .recalc_rate = pll_recalc_rate,
+ .round_rate = pll_round_rate,
+ .set_rate = pll_set_rate,
+};
+
+static int pll_clk_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const char *parent_name;
+ struct pll_clk *pll_clk;
+ struct resource *mem;
+ struct clk_init_data init = { };
+ int ret;
+
+ pll_clk = devm_kzalloc(dev, sizeof(*pll_clk), GFP_KERNEL);
+ if (!pll_clk)
+ return -ENOMEM;
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ pll_clk->base = devm_ioremap_resource(dev, mem);
+ if (IS_ERR(pll_clk->base))
+ return PTR_ERR(pll_clk->base);
+
+ mem = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ pll_clk->lock = devm_ioremap_resource(dev, mem);
+ if (IS_ERR(pll_clk->lock))
+ return PTR_ERR(pll_clk->base);
+
+ init.name = dev->of_node->name;
+ init.ops = &pll_ops;
+ parent_name = of_clk_get_parent_name(dev->of_node, 0);
+ init.parent_names = &parent_name;
+ init.num_parents = 1;
+ pll_clk->hw.init = &init;
+ pll_clk->dev = dev;
+ pll_clk->pll_cfg = of_device_get_match_data(dev);
+
+ if (!pll_clk->pll_cfg) {
+ dev_err(dev, "No OF match data provided\n");
+ return -EINVAL;
+ }
+
+ ret = devm_clk_hw_register(dev, &pll_clk->hw);
+ if (ret) {
+ dev_err(dev, "failed to register %s clock\n", init.name);
+ return ret;
+ }
+
+ return of_clk_add_hw_provider(dev->of_node, of_clk_hw_simple_get,
+ &pll_clk->hw);
+}
+
+static int pll_clk_remove(struct platform_device *pdev)
+{
+ of_clk_del_provider(pdev->dev.of_node);
+ return 0;
+}
+
+static void __init of_pll_clk_setup(struct device_node *node)
+{
+ const char *parent_name;
+ struct pll_clk *pll_clk;
+ struct clk_init_data init = { };
+ int ret;
+
+ pll_clk = kzalloc(sizeof(*pll_clk), GFP_KERNEL);
+ if (!pll_clk)
+ return;
+
+ pll_clk->base = of_iomap(node, 0);
+ if (!pll_clk->base) {
+ pr_err("failed to map pll div registers\n");
+ iounmap(pll_clk->base);
+ return;
+ }
+
+ pll_clk->lock = of_iomap(node, 1);
+ if (!pll_clk->lock) {
+ pr_err("failed to map pll lock register\n");
+ iounmap(pll_clk->lock);
+ return;
+ }
+
+ init.name = node->name;
+ init.ops = &pll_ops;
+ parent_name = of_clk_get_parent_name(node, 0);
+ init.parent_names = &parent_name;
+ init.num_parents = parent_name ? 1 : 0;
+ pll_clk->hw.init = &init;
+ pll_clk->pll_cfg = arc_pll_cfg;
+
+ ret = clk_hw_register(NULL, &pll_clk->hw);
+ if (ret) {
+ pr_err("failed to register %s clock\n", node->name);
+ kfree(pll_clk);
+ return;
+ }
+
+ of_clk_add_hw_provider(node, of_clk_hw_simple_get, &pll_clk->hw);
+}
+
+CLK_OF_DECLARE(axs10x_pll_clock, "snps,axs10x-arc-pll-clock", of_pll_clk_setup);
+
+static const struct of_device_id pll_clk_id[] = {
+ { .compatible = "snps,axs10x-pgu-pll-clock", .data = &pgu_pll_cfg},
+ { },
+};
+MODULE_DEVICE_TABLE(of, pll_clk_id);
+
+static struct platform_driver pll_clk_driver = {
+ .driver = {
+ .name = "axs10x-pll-clock",
+ .of_match_table = pll_clk_id,
+ },
+ .probe = pll_clk_probe,
+ .remove = pll_clk_remove,
+};
+builtin_platform_driver(pll_clk_driver);
+
+MODULE_AUTHOR("Vlad Zakharov <vzakhar at synopsys.com>");
+MODULE_DESCRIPTION("Synopsys AXS10X SDP Generic PLL Clock Driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
