Hi Jose, On Mon, 2016-03-28 at 15:36 +0100, Jose Abreu wrote: > HDMI audio support was added to the AXS board using an > I2S cpu driver and a custom platform driver. > > The platform driver supports two channels @ 16 bits with > rates 32k, 44.1k and 48k. ALSA Simple audio card is used to > glue the cpu, platform and codec driver (adv7511). > > Signed-off-by: Jose Abreu <joabreu at synopsys.com> > --- > > No changes v1 -> v2. > > ?sound/soc/dwc/Kconfig??????????|???1 + > ?sound/soc/dwc/designware_i2s.c | 385 +++++++++++++++++++++++++++++++++++++++-- > ?2 files changed, 373 insertions(+), 13 deletions(-) > > diff --git a/sound/soc/dwc/Kconfig b/sound/soc/dwc/Kconfig > index d50e085..bc3fae7 100644 > --- a/sound/soc/dwc/Kconfig > +++ b/sound/soc/dwc/Kconfig > @@ -2,6 +2,7 @@ config SND_DESIGNWARE_I2S > ? tristate "Synopsys I2S Device Driver" > ? depends on CLKDEV_LOOKUP > ? select SND_SOC_GENERIC_DMAENGINE_PCM > + select SND_SIMPLE_CARD > ? help > ? ?Say Y or M if you want to add support for I2S driver for > ? ?Synopsys desigwnware I2S device. The device supports upto > diff --git a/sound/soc/dwc/designware_i2s.c b/sound/soc/dwc/designware_i2s.c > index bff258d..0f2f588 100644 > --- a/sound/soc/dwc/designware_i2s.c > +++ b/sound/soc/dwc/designware_i2s.c > @@ -84,11 +84,37 @@ > ?#define MAX_CHANNEL_NUM 8 > ?#define MIN_CHANNEL_NUM 2 > ? > +/* FPGA Version Info */ > +#define FPGA_VER_INFO 0xE0011230 > +#define FPGA_VER_27M 0x000FBED9 > + > +/* PLL registers addresses */ > +#define PLL_IDIV_ADDR 0xE00100A0 > +#define PLL_FBDIV_ADDR 0xE00100A4 > +#define PLL_ODIV0_ADDR 0xE00100A8 > +#define PLL_ODIV1_ADDR 0xE00100AC Well I think all is not acceptable. See all these?FPGA_VER_xxx as well as?PLL_xxx are strictly ARC SDP specific things and have nothing to do with generic driver. That's so pity we don't have a driver for all clocks/PLLs on ARC SDP yet. So as of now I may only propose to use hard-coded fixed clocks as I did with ARC PGU, see "pguclk" here: http://lists.infradead.org/pipermail/linux-snps-arc/2016-March/000790.html Again I'll try to implement missing clock driver sometime soon because more and more stuff requires it but for now let's use a work-around. > +struct dw_i2s_pll { > + unsigned int rate; > + unsigned int data_width; > + unsigned int idiv; > + unsigned int fbdiv; > + unsigned int odiv0; > + unsigned int odiv1; > +}; > + > +static const struct dw_i2s_pll dw_i2s_pll_cfg_27m[] = { > + /* 27Mhz */ > + { 32000, 16, 0x104, 0x451, 0x10E38, 0x2000 }, > + { 44100, 16, 0x104, 0x596, 0x10D35, 0x2000 }, > + { 48000, 16, 0x208, 0xA28, 0x10B2C, 0x2000 }, > + { 0, 0, 0, 0, 0, 0 }, > ?}; > ? > +static const struct dw_i2s_pll dw_i2s_pll_cfg_28m[] = { > + /* 28.224Mhz */ > + { 32000, 16, 0x82, 0x105, 0x107DF, 0x2000 }, > + { 44100, 16, 0x28A, 0x1, 0x10001, 0x2000 }, > + { 48000, 16, 0xA28, 0x187, 0x10042, 0x2000 }, > + { 0, 0, 0, 0, 0, 0 }, > +}; These 2 hunks as well should go in ARC SDP clocks. > +static int i2s_pll_cfg(struct i2s_clk_config_data *config) > +{ > + const struct dw_i2s_pll *pll_cfg; > + u32 rate = config->sample_rate; > + u32 data_width = config->data_width; > + int i; > + > + if (readl((void *)FPGA_VER_INFO) <= FPGA_VER_27M) > + pll_cfg = dw_i2s_pll_cfg_27m; > + else > + pll_cfg = dw_i2s_pll_cfg_28m; > + > + for (i = 0; pll_cfg[i].rate != 0; i++) { > + if ((pll_cfg[i].rate == rate) && > + (pll_cfg[i].data_width == data_width)) { > + writel(pll_cfg[i].idiv, (void *)PLL_IDIV_ADDR); > + writel(pll_cfg[i].fbdiv, (void *)PLL_FBDIV_ADDR); > + writel(pll_cfg[i].odiv0, (void *)PLL_ODIV0_ADDR); > + writel(pll_cfg[i].odiv1, (void *)PLL_ODIV1_ADDR); > + return 0; > + } > + } > + > + return -EINVAL; > +} Ditto. -Alexey
