On Wed, Apr 18, 2018 at 12:27:02PM +0200, Michael Nazzareno Trimarchi wrote: > Hi > > On Wed, Apr 18, 2018 at 11:59 AM, Russell King - ARM Linux > <linux@xxxxxxxxxxxxxxx> wrote: > > On Wed, Apr 18, 2018 at 02:41:43PM +0530, Vignesh R wrote: > >> > >> > >> On Tuesday 17 April 2018 02:50 PM, Vignesh R wrote: > >> > > >> > > >> > On Monday 16 April 2018 09:15 PM, Tony Lindgren wrote: > >> >> * Russell King - ARM Linux <linux@xxxxxxxxxxxxxxx> [180416 15:19]: > >> >>> Hi, > >> >>> > >> >>> I'm not entirely sure what's going on, but I see corrupted characters > >> >>> with the serial console on the OMAP4430 SDP board. During boot, > >> >>> everything seems fine, the problem appears to be userspace output. > >> >>> > >> >>> For example, if I edit a file, then quit vi: > >> >>> > >> >>> :q■■%■■B■■Z■root@omap-4430sdp:~# > >> >> > >> >> I don't think I've seen that one. What I've seen few times is > >> >> typing a key on the serial console echoing back the previous > >> >> character typed while the new character won't get displayed > >> >> until hitting keyboard again. Only rebooting the device seems > >> >> to solve this. This is with 4430 ES2.3 revision. > >> >> > >> >> I wonder if we're missing some parts of errata i202 handling > >> >> in omap_8250_mdr1_errataset()? > >> >> > >> > >> I wonder if the extra read of MDR1 register at the beginning of > >> omap_8250_mdr1_errataset() compared to omap-serial is the issue. > >> errata i202 says access to MDR1 can cause data corruption. > >> Assuming both reads and writes can cause glitch then, that read > >> is not following advisory: > >> > >> I don't have SDP board so, could you verify if below diff helps: > >> > >> > >> diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c > >> index 6aaa84355fd1..8ab9d0a1b1eb 100644 > >> --- a/drivers/tty/serial/8250/8250_omap.c > >> +++ b/drivers/tty/serial/8250/8250_omap.c > >> @@ -163,11 +163,6 @@ static void omap_8250_mdr1_errataset(struct uart_8250_port *up, > >> struct omap8250_priv *priv) > >> { > >> u8 timeout = 255; > >> - u8 old_mdr1; > >> - > >> - old_mdr1 = serial_in(up, UART_OMAP_MDR1); > >> - if (old_mdr1 == priv->mdr1) > >> - return; > >> > >> serial_out(up, UART_OMAP_MDR1, priv->mdr1); > >> udelay(2); > > > > That doesn't appear to help. > > > > Looking at the bitstream and comparing what should have been sent with > > what was sent, there appears to be some correlation between the two. > > It looks like the FTDI is not properly synchronised to the bitstream > > coming from the OMAP4430. > > > > Setting two stop bits on both ends (OMAP4430 and FTDI) appears to > > improve the issue, but not completely solve it. > > Are you sure about clock error above some tollerance? No idea at the moment. Looking at the bitstream with a scope is the next step, but it's not easy to do that with just two hands. I also need to find some way to trigger it reliably. Another cause could be that the UART pin is being held high/low for some reason (maybe a pinmux problem.) Another interesting observation is that if I login over the network and then do: while :; do :; done & while :; do :; done & to occupy both CPUs, and then do: dmesg | less on the console, the problem goes away. If I only do one while loop, the problem is present, but the corruption looks like it happens at a different point in the serial stream. This would seem to point the blame away from clocks or pinmux, and back to power management issues. I've also tried mimicking the less output with a stand-alone program, and that doesn't exhibit the problem - I've tried with various initial delays between program start and first output, but this doesn't seem to have much effect. So it seems to need rather precise timing. stracing less does change where the corruption happens in the output, which also suggests a timing related cause. -- RMK's Patch system: http://www.armlinux.org.uk/developer/patches/ FTTC broadband for 0.8mile line in suburbia: sync at 8.8Mbps down 630kbps up According to speedtest.net: 8.21Mbps down 510kbps up -- To unsubscribe from this list: send the line "unsubscribe linux-serial" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html