Hi Jeremy, >>> Realtek RTL8723BS and RTL8723DS are SDIO wifi chips with an embedded >>> Bluetooth controller which connects to the host via UART. >>> The H5 protocol is used for communication between host and device. >>> >>> The Realtek "rtl8723bs_bt" and "rtl8723ds_bt" userspace Bluetooth UART >>> initialization tools (rtk_hciattach) use the following sequence: >>> 1) send H5 sync pattern (already supported by hci_h5) >>> 2) get LMP version (already supported by btrtl) >>> 3) get ROM version (already supported by btrtl) >>> 4) load the firmware and config for the current chipset (already >>> supported by btrtl) >>> 5) read UART settings from the config blob (already supported by btrtl) >>> 6) send UART settings via a vendor command to the device (which changes >>> the baudrate of the device and enables or disables flow control >>> depending on the config) >>> 7) change the baudrate and flow control settings on the host >>> 8) send the firmware and config blob to the device (already supported by >>> btrtl) >>> >>> This uses the serdev library as well as the existing btrtl driver to >>> initialize the Bluetooth functionality, which consists of: >>> - identifying the device and loading the corresponding firmware and >>> config blobs (steps #2, #3 and #4) >>> - configuring the baudrate and flow control (steps #6 and #7) >>> - uploading the firmware to the device (step #8) >>> >>> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@xxxxxxxxxxxxxx> >>> --- >>> drivers/bluetooth/Kconfig | 1 + >>> drivers/bluetooth/hci_h5.c | 195 ++++++++++++++++++++++++++++++++++++++++++++- >>> 2 files changed, 195 insertions(+), 1 deletion(-) >>> >>> diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig >>> index 60e1c7d6986d..3001f1200c72 100644 >>> --- a/drivers/bluetooth/Kconfig >>> +++ b/drivers/bluetooth/Kconfig >>> @@ -146,6 +146,7 @@ config BT_HCIUART_LL >>> config BT_HCIUART_3WIRE >>> bool "Three-wire UART (H5) protocol support" >>> depends on BT_HCIUART >>> + select BT_RTL if SERIAL_DEV_BUS >>> help >>> The HCI Three-wire UART Transport Layer makes it possible to >>> user the Bluetooth HCI over a serial port interface. The HCI >> >> so I just posted a bt3wire.c driver that is serdev only and written from scratch. On a RPi3 Broadcom chip it kinda works. I think there is a lot of extra work to be done, but this might be a better starting point for Realtek UART devices. > > I picked up the v2 version of this RFC and rebased it to the latest > bluetooth-next and added ACPI support. It also kinda works, but there's > a few problems left to track down and I still haven't looked into > getting rid of the config blobs. > > It sounded like Martin wasn't going to be able to get to this until > at least the 4.18 cycle, so unless he objects I'm going to look at > getting what I've got working with that bt3wire.c driver. yes please, have a look at the bt3wire.c code that I send and see if you can make it work with Realtek controllers. On the RPi3 with the Broadcom controller it kinda works, but firmware loading and btmgmt power on/off seem to have issues. The power on/off might be caused because I moved the serdev_device_open and link establishment into the hdev->open callback and don’t clean up properly on hdev->close. However I really think it belongs there and thus we should make this work. You will notice that the link establishment is also kinda slow (at least on Broadcom devices) where the messages only happen once per second. We can try to send every 250 msec and see if that changes things. If the Bluetooth stack is powered down, we should also not have the serial device opened. On USB it is the same since it is bound, but no URBs are active. For me the real advantage of a standalone bt3wire.c is that we no longer have spagetti code through hci_ldisc.c and hci_serdev.c and hci_*.c drivers that got rather complicated to follow. On a side note, in btuart.c, I put all the serdev settings into the hdev->setup callback, but I think with bt3wire.c that is not possible due to 3-Wire protocol. So I assume we need vendor_open, vendor_close and vendor_setup additions in bt3wire.c Regards Marcel -- To unsubscribe from this list: send the line "unsubscribe linux-serial" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
