This driver supports GENI based UART Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including UART. This driver support console
operations using FIFO mode of transfer.
Signed-off-by: Girish Mahadevan <girishm@xxxxxxxxxxxxxx>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@xxxxxxxxxxxxxx>
Signed-off-by: Sagar Dharia <sdharia@xxxxxxxxxxxxxx>
Signed-off-by: Doug Anderson <dianders@xxxxxxxxxx>
---
drivers/tty/serial/Kconfig | 11 +
drivers/tty/serial/Makefile | 1 +
drivers/tty/serial/qcom_geni_serial.c | 1181 +++++++++++++++++++++++++++++++++
3 files changed, 1193 insertions(+)
create mode 100644 drivers/tty/serial/qcom_geni_serial.c
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 3682fd3..c6b1500 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -1104,6 +1104,17 @@ config SERIAL_MSM_CONSOLE
select SERIAL_CORE_CONSOLE
select SERIAL_EARLYCON
+config SERIAL_QCOM_GENI
+ bool "QCOM on-chip GENI based serial port support"
+ depends on ARCH_QCOM
+ depends on QCOM_GENI_SE
+ select SERIAL_CORE
+ select SERIAL_CORE_CONSOLE
+ select SERIAL_EARLYCON
+ help
+ Serial driver for Qualcomm Technologies Inc's GENI based QUP
+ hardware.
+
config SERIAL_VT8500
bool "VIA VT8500 on-chip serial port support"
depends on ARCH_VT8500
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index 842d185..64a8d82 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -63,6 +63,7 @@ obj-$(CONFIG_SERIAL_SGI_IOC3) += ioc3_serial.o
obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
obj-$(CONFIG_SERIAL_UARTLITE) += uartlite.o
obj-$(CONFIG_SERIAL_MSM) += msm_serial.o
+obj-$(CONFIG_SERIAL_QCOM_GENI) += qcom_geni_serial.o
obj-$(CONFIG_SERIAL_NETX) += netx-serial.o
obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
new file mode 100644
index 0000000..8536b7d
--- /dev/null
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -0,0 +1,1181 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2017-2018, The Linux foundation. All rights reserved.
+
+#include <linux/console.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/qcom-geni-se.h>
+#include <linux/serial.h>
+#include <linux/serial_core.h>
+#include <linux/slab.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+
+/* UART specific GENI registers */
+#define SE_UART_TX_TRANS_CFG 0x25c
+#define SE_UART_TX_WORD_LEN 0x268
+#define SE_UART_TX_STOP_BIT_LEN 0x26c
+#define SE_UART_TX_TRANS_LEN 0x270
+#define SE_UART_RX_TRANS_CFG 0x280
+#define SE_UART_RX_WORD_LEN 0x28c
+#define SE_UART_RX_STALE_CNT 0x294
+#define SE_UART_TX_PARITY_CFG 0x2a4
+#define SE_UART_RX_PARITY_CFG 0x2a8
+
+/* SE_UART_TRANS_CFG */
+#define UART_TX_PAR_EN BIT(0)
+#define UART_CTS_MASK BIT(1)
+
+/* SE_UART_TX_WORD_LEN */
+#define TX_WORD_LEN_MSK GENMASK(9, 0)
+
+/* SE_UART_TX_STOP_BIT_LEN */
+#define TX_STOP_BIT_LEN_MSK GENMASK(23, 0)
+#define TX_STOP_BIT_LEN_1 0
+#define TX_STOP_BIT_LEN_1_5 1
+#define TX_STOP_BIT_LEN_2 2
+
+/* SE_UART_TX_TRANS_LEN */
+#define TX_TRANS_LEN_MSK GENMASK(23, 0)
+
+/* SE_UART_RX_TRANS_CFG */
+#define UART_RX_INS_STATUS_BIT BIT(2)
+#define UART_RX_PAR_EN BIT(3)
+
+/* SE_UART_RX_WORD_LEN */
+#define RX_WORD_LEN_MASK GENMASK(9, 0)
+
+/* SE_UART_RX_STALE_CNT */
+#define RX_STALE_CNT GENMASK(23, 0)
+
+/* SE_UART_TX_PARITY_CFG/RX_PARITY_CFG */
+#define PAR_CALC_EN BIT(0)
+#define PAR_MODE_MSK GENMASK(2, 1)
+#define PAR_MODE_SHFT 1
+#define PAR_EVEN 0x00
+#define PAR_ODD 0x01
+#define PAR_SPACE 0x10
+#define PAR_MARK 0x11
+
+/* UART M_CMD OP codes */
+#define UART_START_TX 0x1
+#define UART_START_BREAK 0x4
+#define UART_STOP_BREAK 0x5
+/* UART S_CMD OP codes */
+#define UART_START_READ 0x1
+#define UART_PARAM 0x1
+
+#define UART_OVERSAMPLING 32
+#define STALE_TIMEOUT 16
+#define DEFAULT_BITS_PER_CHAR 10
+#define GENI_UART_CONS_PORTS 1
+#define DEF_FIFO_DEPTH_WORDS 16
+#define DEF_TX_WM 2
+#define DEF_FIFO_WIDTH_BITS 32
+#define UART_CONSOLE_RX_WM 2
+
+#ifdef CONFIG_CONSOLE_POLL
+#define RX_BYTES_PW 1
+#else
+#define RX_BYTES_PW 4
+#endif
+
+struct qcom_geni_serial_port {
+ struct uart_port uport;
+ struct geni_se se;
+ char name[20];
+ u32 tx_fifo_depth;
+ u32 tx_fifo_width;
+ u32 rx_fifo_depth;
+ u32 tx_wm;
+ u32 rx_wm;
+ u32 rx_rfr;
+ int xfer_mode;
+ bool port_setup;
+ int (*handle_rx)(struct uart_port *uport,
+ u32 rx_bytes, bool drop_rx);
+ unsigned int xmit_size;
+ unsigned int cur_baud;
+ unsigned int tx_bytes_pw;
+ unsigned int rx_bytes_pw;
+};
+
+static const struct uart_ops qcom_geni_serial_pops;
+static struct uart_driver qcom_geni_console_driver;
+static int handle_rx_console(struct uart_port *uport,
+ u32 rx_bytes, bool drop_rx);
+static unsigned int qcom_geni_serial_tx_empty(struct uart_port *port);
+static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
+ int offset, int bit_field, bool set);
+static void qcom_geni_serial_stop_rx(struct uart_port *uport);
+
+static atomic_t uart_line_id = ATOMIC_INIT(0);
+static const unsigned long root_freq[] = {7372800, 14745600, 19200000, 29491200,
+ 32000000, 48000000, 64000000, 80000000,
+ 96000000, 100000000};
+
+#define to_dev_port(ptr, member) \
+ container_of(ptr, struct qcom_geni_serial_port, member)
+
+static struct qcom_geni_serial_port qcom_geni_console_port;
+
+static void qcom_geni_serial_config_port(struct uart_port *uport, int cfg_flags)
+{
+ if (cfg_flags & UART_CONFIG_TYPE)
+ uport->type = PORT_MSM;
+}
+
+static unsigned int qcom_geni_cons_get_mctrl(struct uart_port *uport)
+{
+ return TIOCM_DSR | TIOCM_CAR | TIOCM_CTS;
+}
+
+static void qcom_geni_cons_set_mctrl(struct uart_port *uport,
+ unsigned int mctrl)
+{
+}
+
+static const char *qcom_geni_serial_get_type(struct uart_port *uport)
+{
+ return "MSM";
+}
+
+static struct qcom_geni_serial_port *get_port_from_line(int line)
+{
+ if ((line < 0) || (line >= GENI_UART_CONS_PORTS))
+ return ERR_PTR(-ENXIO);
+ return &qcom_geni_console_port;
+}
+
+static bool qcom_geni_serial_poll_bit(struct uart_port *uport,
+ int offset, int bit_field, bool set)
+{
+ u32 reg;
+ struct qcom_geni_serial_port *port;
+ unsigned int baud;
+ unsigned int fifo_bits;
+ unsigned long timeout_us = 20000;
+
+ /* Ensure polling is not re-ordered before the prior writes/reads */
+ mb();
+
+ if (uport->private_data) {
+ port = to_dev_port(uport, uport);
+ baud = port->cur_baud;
+ if (!baud)
+ baud = 115200;
+ fifo_bits = port->tx_fifo_depth * port->tx_fifo_width;
+ /*
+ * Total polling iterations based on FIFO worth of bytes to be
+ * sent at current baud .Add a little fluff to the wait.
+ */
+ timeout_us = ((fifo_bits * USEC_PER_SEC) / baud) + 500;
+ }
+
+ return !readl_poll_timeout_atomic(uport->membase + offset, reg,
+ (bool)(reg & bit_field) == set, 10, timeout_us);
+}
+
+static void qcom_geni_serial_setup_tx(struct uart_port *uport, u32 xmit_size)
+{
+ u32 m_cmd;
+
+ writel_relaxed(xmit_size, uport->membase + SE_UART_TX_TRANS_LEN);
+ m_cmd = UART_START_TX << M_OPCODE_SHFT;
+ writel(m_cmd, uport->membase + SE_GENI_M_CMD0);
+}
+
+static void qcom_geni_serial_poll_tx_done(struct uart_port *uport)
+{
+ int done;
+ u32 irq_clear = M_CMD_DONE_EN;
+
+ done = qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+ M_CMD_DONE_EN, true);
+ if (!done) {
+ writel_relaxed(M_GENI_CMD_ABORT, uport->membase +
+ SE_GENI_M_CMD_CTRL_REG);
+ irq_clear |= M_CMD_ABORT_EN;
+ qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+ M_CMD_ABORT_EN, true);
+ }
+ writel_relaxed(irq_clear, uport->membase + SE_GENI_M_IRQ_CLEAR);
+}
+
+static void qcom_geni_serial_abort_rx(struct uart_port *uport)
+{
+ u32 irq_clear = S_CMD_DONE_EN | S_CMD_ABORT_EN;
+
+ writel(S_GENI_CMD_ABORT, uport->membase + SE_GENI_S_CMD_CTRL_REG);
+ qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
+ S_GENI_CMD_ABORT, false);
+ writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
+ writel_relaxed(FORCE_DEFAULT, uport->membase + GENI_FORCE_DEFAULT_REG);
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+static int qcom_geni_serial_get_char(struct uart_port *uport)
+{
+ u32 rx_fifo;
+ u32 status;
+
+ status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
+ writel_relaxed(status, uport->membase + SE_GENI_M_IRQ_CLEAR);
+
+ status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
+ writel_relaxed(status, uport->membase + SE_GENI_S_IRQ_CLEAR);
+
+ /*
+ * Ensure the writes to clear interrupts is not re-ordered after
+ * reading the data.
+ */
+ mb();
+
+ status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS);
+ if (!(status & RX_FIFO_WC_MSK))
+ return NO_POLL_CHAR;
+
+ rx_fifo = readl(uport->membase + SE_GENI_RX_FIFOn);
+ return rx_fifo & 0xff;
+}
+
+static void qcom_geni_serial_poll_put_char(struct uart_port *uport,
+ unsigned char c)
+{
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+ writel_relaxed(port->tx_wm, uport->membase + SE_GENI_TX_WATERMARK_REG);
+ qcom_geni_serial_setup_tx(uport, 1);
+ WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+ M_TX_FIFO_WATERMARK_EN, true));
+ writel_relaxed((u32)c, uport->membase + SE_GENI_TX_FIFOn);
+ writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
+ SE_GENI_M_IRQ_CLEAR);
+ qcom_geni_serial_poll_tx_done(uport);
+}
+#endif
+
+#if defined(CONFIG_SERIAL_CORE_CONSOLE) || defined(CONFIG_CONSOLE_POLL)
+static void qcom_geni_serial_wr_char(struct uart_port *uport, int ch)
+{
+ writel_relaxed(ch, uport->membase + SE_GENI_TX_FIFOn);
+}
+
+static void
+__qcom_geni_serial_console_write(struct uart_port *uport, const char *s,
+ unsigned int count)
+{
+ int new_line = 0;
+ int i;
+ u32 bytes_to_send = count;
+
+ for (i = 0; i < count; i++) {
+ if (s[i] == '\n')
+ new_line++;
+ }
+
+ bytes_to_send += new_line;
+ writel_relaxed(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
+ qcom_geni_serial_setup_tx(uport, bytes_to_send);
+ i = 0;
+ while (i < count) {
+ size_t chars_to_write = 0;
+ size_t avail = DEF_FIFO_DEPTH_WORDS - DEF_TX_WM;
+
+ /*
+ * If the WM bit never set, then the Tx state machine is not
+ * in a valid state, so break, cancel/abort any existing
+ * command. Unfortunately the current data being written is
+ * lost.
+ */
+ while (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+ M_TX_FIFO_WATERMARK_EN, true))
+ break;
+ chars_to_write = min_t(size_t, (size_t)(count - i), avail / 2);
+ uart_console_write(uport, (s + i), chars_to_write,
+ qcom_geni_serial_wr_char);
+ writel_relaxed(M_TX_FIFO_WATERMARK_EN, uport->membase +
+ SE_GENI_M_IRQ_CLEAR);
+ i += chars_to_write;
+ }
+ qcom_geni_serial_poll_tx_done(uport);
+}
+
+static void qcom_geni_serial_console_write(struct console *co, const char *s,
+ unsigned int count)
+{
+ struct uart_port *uport;
+ struct qcom_geni_serial_port *port;
+ bool locked = true;
+ unsigned long flags;
+
+ WARN_ON(co->index < 0 || co->index >= GENI_UART_CONS_PORTS);
+
+ port = get_port_from_line(co->index);
+ if (IS_ERR(port))
+ return;
+
+ uport = &port->uport;
+ if (oops_in_progress)
+ locked = spin_trylock_irqsave(&uport->lock, flags);
+ else
+ spin_lock_irqsave(&uport->lock, flags);
+
+ if (locked) {
+ __qcom_geni_serial_console_write(uport, s, count);
+ spin_unlock_irqrestore(&uport->lock, flags);
+ }
+}
+
+static int handle_rx_console(struct uart_port *uport, u32 rx_bytes, bool drop)
+{
+ u32 i = rx_bytes;
+ u32 rx_fifo;
+ unsigned char *buf;
+ struct tty_port *tport;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+ tport = &uport->state->port;
+ while (i > 0) {
+ int c;
+ int bytes = i > port->rx_bytes_pw ? port->rx_bytes_pw : i;
+
+ rx_fifo = readl_relaxed(uport->membase + SE_GENI_RX_FIFOn);
+ i -= bytes;
+ if (drop)
+ continue;
+ buf = (unsigned char *)&rx_fifo;
+
+ for (c = 0; c < bytes; c++) {
+ int sysrq;
+
+ uport->icount.rx++;
+ sysrq = uart_handle_sysrq_char(uport, buf[c]);
+ if (!sysrq)
+ tty_insert_flip_char(tport, buf[c], TTY_NORMAL);
+ }
+ }
+ if (!drop)
+ tty_flip_buffer_push(tport);
+ return 0;
+}
+#else
+static int handle_rx_console(struct uart_port *uport,
+ unsigned int rx_fifo_wc,
+ unsigned int rx_last_byte_valid,
+ unsigned int rx_last,
+ bool drop_rx)
+{
+ return -EPERM;
+}
+
+#endif /* (CONFIG_SERIAL_CORE_CONSOLE) || defined(CONFIG_CONSOLE_POLL)) */
+
+static void qcom_geni_serial_start_tx(struct uart_port *uport)
+{
+ u32 irq_en;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+ u32 status;
+
+ if (port->xfer_mode == GENI_SE_FIFO) {
+ status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+ if (status & M_GENI_CMD_ACTIVE)
+ return;
+
+ if (!qcom_geni_serial_tx_empty(uport))
+ return;
+
+ /*
+ * Ensure writing to IRQ_EN & watermark registers are not
+ * re-ordered before checking the status of the Serial
+ * Engine and TX FIFO
+ */
+ mb();
+
+ irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN;
+
+ writel_relaxed(port->tx_wm, uport->membase +
+ SE_GENI_TX_WATERMARK_REG);
+ writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+ }
+}
+
+static void qcom_geni_serial_stop_tx(struct uart_port *uport)
+{
+ u32 irq_en;
+ u32 status;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+ irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en &= ~M_CMD_DONE_EN;
+ if (port->xfer_mode == GENI_SE_FIFO) {
+ irq_en &= ~M_TX_FIFO_WATERMARK_EN;
+ writel_relaxed(0, uport->membase +
+ SE_GENI_TX_WATERMARK_REG);
+ }
+ port->xmit_size = 0;
+ writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+ status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+ /* Possible stop tx is called multiple times. */
+ if (!(status & M_GENI_CMD_ACTIVE))
+ return;
+
+ /*
+ * Ensure cancel command write is not re-ordered before checking
+ * checking the status of the Primary Sequencer.
+ */
+ mb();
+
+ geni_se_cancel_m_cmd(&port->se);
+ if (!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+ M_CMD_CANCEL_EN, true)) {
+ geni_se_abort_m_cmd(&port->se);
+ qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+ M_CMD_ABORT_EN, true);
+ writel_relaxed(M_CMD_ABORT_EN, uport->membase +
+ SE_GENI_M_IRQ_CLEAR);
+ }
+ writel_relaxed(M_CMD_CANCEL_EN, uport->membase + SE_GENI_M_IRQ_CLEAR);
+}
+
+static void qcom_geni_serial_start_rx(struct uart_port *uport)
+{
+ u32 irq_en;
+ u32 status;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+ status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+ if (status & S_GENI_CMD_ACTIVE)
+ qcom_geni_serial_stop_rx(uport);
+
+ /*
+ * Ensure setup command write is not re-ordered before checking
+ * checking the status of the Secondary Sequencer.
+ */
+ mb();
+
+ geni_se_setup_s_cmd(&port->se, UART_START_READ, 0);
+
+ if (port->xfer_mode == GENI_SE_FIFO) {
+ irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
+ irq_en |= S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN;
+ writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
+
+ irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN;
+ writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+ }
+}
+
+static void qcom_geni_serial_stop_rx(struct uart_port *uport)
+{
+ u32 irq_en;
+ u32 status;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+ u32 irq_clear = S_CMD_DONE_EN;
+
+ if (port->xfer_mode == GENI_SE_FIFO) {
+ irq_en = readl_relaxed(uport->membase + SE_GENI_S_IRQ_EN);
+ irq_en &= ~(S_RX_FIFO_WATERMARK_EN | S_RX_FIFO_LAST_EN);
+ writel_relaxed(irq_en, uport->membase + SE_GENI_S_IRQ_EN);
+
+ irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ irq_en &= ~(M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN);
+ writel_relaxed(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
+ }
+
+ status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+ /* Possible stop rx is called multiple times. */
+ if (!(status & S_GENI_CMD_ACTIVE))
+ return;
+
+ /*
+ * Ensure cancel command write is not re-ordered before checking
+ * checking the status of the Secondary Sequencer.
+ */
+ mb();
+
+ geni_se_cancel_s_cmd(&port->se);
+ qcom_geni_serial_poll_bit(uport, SE_GENI_S_CMD_CTRL_REG,
+ S_GENI_CMD_CANCEL, false);
+ status = readl_relaxed(uport->membase + SE_GENI_STATUS);
+ writel_relaxed(irq_clear, uport->membase + SE_GENI_S_IRQ_CLEAR);
+ if (status & S_GENI_CMD_ACTIVE)
+ qcom_geni_serial_abort_rx(uport);
+}
+
+static void qcom_geni_serial_handle_rx(struct uart_port *uport, bool drop_rx)
+{
+ u32 status;
+ u32 word_cnt;
+ u32 last_word_byte_cnt;
+ u32 last_word_partial;
+ u32 total_bytes;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+ status = readl_relaxed(uport->membase + SE_GENI_RX_FIFO_STATUS);
+ word_cnt = status & RX_FIFO_WC_MSK;
+ last_word_partial = status & RX_LAST;
+ last_word_byte_cnt = (status & RX_LAST_BYTE_VALID_MSK) >>
+ RX_LAST_BYTE_VALID_SHFT;
+
+ if (!word_cnt)
+ return;
+ total_bytes = port->rx_bytes_pw * (word_cnt - 1);
+ if (last_word_partial && last_word_byte_cnt)
+ total_bytes += last_word_byte_cnt;
+ else
+ total_bytes += port->rx_bytes_pw;
+ port->handle_rx(uport, total_bytes, drop_rx);
+}
+
+static int qcom_geni_serial_handle_tx(struct uart_port *uport)
+{
+ int ret = 0;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+ struct circ_buf *xmit = &uport->state->xmit;
+ size_t avail;
+ size_t remaining;
+ int i = 0;
+ u32 status;
+ unsigned int chunk;
+ int tail;
+
+ chunk = uart_circ_chars_pending(xmit);
+ status = readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS);
+ /* Both FIFO and framework buffer are drained */
+ if ((chunk == port->xmit_size) && !status) {
+ port->xmit_size = 0;
+ uart_circ_clear(xmit);
+ qcom_geni_serial_stop_tx(uport);
+ goto out_write_wakeup;
+ }
+ chunk -= port->xmit_size;
+
+ avail = (port->tx_fifo_depth - port->tx_wm) * port->tx_bytes_pw;
+ tail = (xmit->tail + port->xmit_size) & (UART_XMIT_SIZE - 1);
+ if (chunk > (UART_XMIT_SIZE - tail))
+ chunk = UART_XMIT_SIZE - tail;
+ if (chunk > avail)
+ chunk = avail;
+
+ if (!chunk)
+ goto out_write_wakeup;
+
+ qcom_geni_serial_setup_tx(uport, chunk);
+
+ remaining = chunk;
+ while (i < chunk) {
+ unsigned int tx_bytes;
+ unsigned int buf = 0;
+ int c;
+
+ tx_bytes = min_t(size_t, remaining, (size_t)port->tx_bytes_pw);
+ for (c = 0; c < tx_bytes ; c++)
+ buf |= (xmit->buf[tail + c] << (c * BITS_PER_BYTE));
+
+ writel_relaxed(buf, uport->membase + SE_GENI_TX_FIFOn);
+
+ i += tx_bytes;
+ tail = (tail + tx_bytes) & (UART_XMIT_SIZE - 1);
+ uport->icount.tx += tx_bytes;
+ remaining -= tx_bytes;
+ }
+ qcom_geni_serial_poll_tx_done(uport);
+ port->xmit_size += chunk;
+out_write_wakeup:
+ uart_write_wakeup(uport);
+ return ret;
+}
+
+static irqreturn_t qcom_geni_serial_isr(int isr, void *dev)
+{
+ unsigned int m_irq_status;
+ unsigned int s_irq_status;
+ struct uart_port *uport = dev;
+ unsigned long flags;
+ unsigned int m_irq_en;
+ bool drop_rx = false;
+ struct tty_port *tport = &uport->state->port;
+
+ if (uport->suspended)
+ return IRQ_HANDLED;
+
+ spin_lock_irqsave(&uport->lock, flags);
+ m_irq_status = readl_relaxed(uport->membase + SE_GENI_M_IRQ_STATUS);
+ s_irq_status = readl_relaxed(uport->membase + SE_GENI_S_IRQ_STATUS);
+ m_irq_en = readl_relaxed(uport->membase + SE_GENI_M_IRQ_EN);
+ writel_relaxed(m_irq_status, uport->membase + SE_GENI_M_IRQ_CLEAR);
+ writel_relaxed(s_irq_status, uport->membase + SE_GENI_S_IRQ_CLEAR);
+
+ if (WARN_ON(m_irq_status & M_ILLEGAL_CMD_EN))
+ goto out_unlock;
+
+ if (s_irq_status & S_RX_FIFO_WR_ERR_EN) {
+ uport->icount.overrun++;
+ tty_insert_flip_char(tport, 0, TTY_OVERRUN);
+ }
+
+ if (m_irq_status & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN) &&
+ m_irq_en & (M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN))
+ qcom_geni_serial_handle_tx(uport);
+
+ if (s_irq_status & S_GP_IRQ_0_EN || s_irq_status & S_GP_IRQ_1_EN) {
+ if (s_irq_status & S_GP_IRQ_0_EN)
+ uport->icount.parity++;
+ drop_rx = true;
+ } else if (s_irq_status & S_GP_IRQ_2_EN ||
+ s_irq_status & S_GP_IRQ_3_EN) {
+ uport->icount.brk++;
+ }
+
+ if (s_irq_status & S_RX_FIFO_WATERMARK_EN ||
+ s_irq_status & S_RX_FIFO_LAST_EN)
+ qcom_geni_serial_handle_rx(uport, drop_rx);
+
+out_unlock:
+ spin_unlock_irqrestore(&uport->lock, flags);
+ return IRQ_HANDLED;
+}
+
+static int get_tx_fifo_size(struct qcom_geni_serial_port *port)
+{
+ struct uart_port *uport;
+
+ if (!port)
+ return -ENODEV;
+
+ uport = &port->uport;
+ port->tx_fifo_depth = geni_se_get_tx_fifo_depth(&port->se);
+ if (!port->tx_fifo_depth) {
+ dev_err(uport->dev, "%s:Invalid TX FIFO depth read\n",
+ __func__);
+ return -ENXIO;
+ }
+
+ port->tx_fifo_width = geni_se_get_tx_fifo_width(&port->se);
+ if (!port->tx_fifo_width) {
+ dev_err(uport->dev, "%s:Invalid TX FIFO width read\n",
+ __func__);
+ return -ENXIO;
+ }
+
+ port->rx_fifo_depth = geni_se_get_rx_fifo_depth(&port->se);
+ if (!port->rx_fifo_depth) {
+ dev_err(uport->dev, "%s:Invalid RX FIFO depth read\n",
+ __func__);
+ return -ENXIO;
+ }
+
+ uport->fifosize =
+ (port->tx_fifo_depth * port->tx_fifo_width) / BITS_PER_BYTE;
+ return 0;
+}
+
+static void set_rfr_wm(struct qcom_geni_serial_port *port)
+{
+ /*
+ * Set RFR (Flow off) to FIFO_DEPTH - 2.
+ * RX WM level at 10% RX_FIFO_DEPTH.
+ * TX WM level at 10% TX_FIFO_DEPTH.
+ */
+ port->rx_rfr = port->rx_fifo_depth - 2;
+ port->rx_wm = UART_CONSOLE_RX_WM;
+ port->tx_wm = 2;
+}
+
+static void qcom_geni_serial_shutdown(struct uart_port *uport)
+{
+ unsigned long flags;
+
+ /* Stop the console before stopping the current tx */
+ console_stop(uport->cons);
+
+ disable_irq(uport->irq);
+ free_irq(uport->irq, uport);
+ spin_lock_irqsave(&uport->lock, flags);
+ qcom_geni_serial_stop_tx(uport);
+ qcom_geni_serial_stop_rx(uport);
+ spin_unlock_irqrestore(&uport->lock, flags);
+}
+
+static int qcom_geni_serial_port_setup(struct uart_port *uport)
+{
+ int ret;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+ unsigned int rxstale = DEFAULT_BITS_PER_CHAR * STALE_TIMEOUT;
+
+ set_rfr_wm(port);
+ writel_relaxed(rxstale, uport->membase + SE_UART_RX_STALE_CNT);
+ /*
+ * Make an unconditional cancel on the main sequencer to reset
+ * it else we could end up in data loss scenarios.
+ */
+ port->xfer_mode = GENI_SE_FIFO;
+ qcom_geni_serial_poll_tx_done(uport);
+ geni_se_config_packing(&port->se, BITS_PER_BYTE, port->tx_bytes_pw,
+ false, true, false);
+ geni_se_config_packing(&port->se, BITS_PER_BYTE, port->rx_bytes_pw,
+ false, false, true);
+ ret = geni_se_init(&port->se, port->rx_wm, port->rx_rfr);
+ if (ret) {
+ dev_err(uport->dev, "%s: Fail\n", __func__);
+ return ret;
+ }
+
+ geni_se_select_mode(&port->se, port->xfer_mode);
+ port->port_setup = true;
+ return ret;
+}
+
+static int qcom_geni_serial_startup(struct uart_port *uport)
+{
+ int ret;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+ scnprintf(port->name, sizeof(port->name),
+ "qcom_serial_geni%d", uport->line);
+
+ if (geni_se_read_proto(&port->se) != GENI_SE_UART) {
+ dev_err(uport->dev, "Invalid FW %d loaded.\n",
+ geni_se_read_proto(&port->se));
+ return -ENXIO;
+ }
+
+ get_tx_fifo_size(port);
+ if (!port->port_setup) {
+ ret = qcom_geni_serial_port_setup(uport);
+ if (ret)
+ return ret;
+ }
+
+ ret = request_irq(uport->irq, qcom_geni_serial_isr, IRQF_TRIGGER_HIGH,
+ port->name, uport);
+ if (ret)
+ dev_err(uport->dev, "Failed to get IRQ ret %d\n", ret);
+ return ret;
+}
+
+static unsigned long get_clk_cfg(unsigned long clk_freq)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(root_freq); i++) {
+ if (!(root_freq[i] % clk_freq))
+ return root_freq[i];
+ }
+ return 0;
+}
+
+static void geni_serial_write_term_regs(struct uart_port *uport,
+ u32 tx_trans_cfg, u32 tx_parity_cfg, u32 rx_trans_cfg,
+ u32 rx_parity_cfg, u32 bits_per_char, u32 stop_bit_len,
+ u32 s_clk_cfg)
+{
+ writel_relaxed(tx_trans_cfg, uport->membase + SE_UART_TX_TRANS_CFG);
+ writel_relaxed(tx_parity_cfg, uport->membase + SE_UART_TX_PARITY_CFG);
+ writel_relaxed(rx_trans_cfg, uport->membase + SE_UART_RX_TRANS_CFG);
+ writel_relaxed(rx_parity_cfg, uport->membase + SE_UART_RX_PARITY_CFG);
+ writel_relaxed(bits_per_char, uport->membase + SE_UART_TX_WORD_LEN);
+ writel_relaxed(bits_per_char, uport->membase + SE_UART_RX_WORD_LEN);
+ writel_relaxed(stop_bit_len, uport->membase + SE_UART_TX_STOP_BIT_LEN);
+ writel_relaxed(s_clk_cfg, uport->membase + GENI_SER_M_CLK_CFG);
+ writel_relaxed(s_clk_cfg, uport->membase + GENI_SER_S_CLK_CFG);
+}
+
+static unsigned long get_clk_div_rate(unsigned int baud, unsigned int *clk_div)
+{
+ unsigned long ser_clk;
+ unsigned long desired_clk;
+
+ desired_clk = baud * UART_OVERSAMPLING;
+ ser_clk = get_clk_cfg(desired_clk);
+ if (!ser_clk) {
+ pr_err("%s: Can't find matching DFS entry for baud %d\n",
+ __func__, baud);
+ return ser_clk;
+ }
+
+ *clk_div = ser_clk / desired_clk;
+ return ser_clk;
+}
+
+static void qcom_geni_serial_set_termios(struct uart_port *uport,
+ struct ktermios *termios, struct ktermios *old)
+{
+ unsigned int baud;
+ unsigned int bits_per_char;
+ unsigned int tx_trans_cfg;
+ unsigned int tx_parity_cfg;
+ unsigned int rx_trans_cfg;
+ unsigned int rx_parity_cfg;
+ unsigned int stop_bit_len;
+ unsigned int clk_div;
+ unsigned long ser_clk_cfg;
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+ unsigned long clk_rate;
+
+ qcom_geni_serial_stop_rx(uport);
+ /* baud rate */
+ baud = uart_get_baud_rate(uport, termios, old, 300, 4000000);
+ port->cur_baud = baud;
+ clk_rate = get_clk_div_rate(baud, &clk_div);
+ if (!clk_rate)
+ goto out_restart_rx;
+
+ uport->uartclk = clk_rate;
+ clk_set_rate(port->se.clk, clk_rate);
+ ser_clk_cfg = SER_CLK_EN;
+ ser_clk_cfg |= (clk_div << CLK_DIV_SHFT);
+
+ /* parity */
+ tx_trans_cfg = readl_relaxed(uport->membase + SE_UART_TX_TRANS_CFG);
+ tx_parity_cfg = readl_relaxed(uport->membase + SE_UART_TX_PARITY_CFG);
+ rx_trans_cfg = readl_relaxed(uport->membase + SE_UART_RX_TRANS_CFG);
+ rx_parity_cfg = readl_relaxed(uport->membase + SE_UART_RX_PARITY_CFG);
+ if (termios->c_cflag & PARENB) {
+ tx_trans_cfg |= UART_TX_PAR_EN;
+ rx_trans_cfg |= UART_RX_PAR_EN;
+ tx_parity_cfg |= PAR_CALC_EN;
+ rx_parity_cfg |= PAR_CALC_EN;
+ if (termios->c_cflag & PARODD) {
+ tx_parity_cfg |= PAR_ODD;
+ rx_parity_cfg |= PAR_ODD;
+ } else if (termios->c_cflag & CMSPAR) {
+ tx_parity_cfg |= PAR_SPACE;
+ rx_parity_cfg |= PAR_SPACE;
+ } else {
+ tx_parity_cfg |= PAR_EVEN;
+ rx_parity_cfg |= PAR_EVEN;
+ }
+ } else {
+ tx_trans_cfg &= ~UART_TX_PAR_EN;
+ rx_trans_cfg &= ~UART_RX_PAR_EN;
+ tx_parity_cfg &= ~PAR_CALC_EN;
+ rx_parity_cfg &= ~PAR_CALC_EN;
+ }
+
+ /* bits per char */
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ bits_per_char = 5;
+ break;
+ case CS6:
+ bits_per_char = 6;
+ break;
+ case CS7:
+ bits_per_char = 7;
+ break;
+ case CS8:
+ default:
+ bits_per_char = 8;
+ break;
+ }
+
+ /* stop bits */
+ if (termios->c_cflag & CSTOPB)
+ stop_bit_len = TX_STOP_BIT_LEN_2;
+ else
+ stop_bit_len = TX_STOP_BIT_LEN_1;
+
+ /* flow control, clear the CTS_MASK bit if using flow control. */
+ if (termios->c_cflag & CRTSCTS)
+ tx_trans_cfg &= ~UART_CTS_MASK;
+ else
+ tx_trans_cfg |= UART_CTS_MASK;
+
+ if (baud)
+ uart_update_timeout(uport, termios->c_cflag, baud);
+
+ geni_serial_write_term_regs(uport, tx_trans_cfg, tx_parity_cfg,
+ rx_trans_cfg, rx_parity_cfg, bits_per_char, stop_bit_len,
+ ser_clk_cfg);
+out_restart_rx:
+ qcom_geni_serial_start_rx(uport);
+}
+
+static unsigned int qcom_geni_serial_tx_empty(struct uart_port *uport)
+{
+ return !readl_relaxed(uport->membase + SE_GENI_TX_FIFO_STATUS);
+}
+
+#if defined(CONFIG_SERIAL_CORE_CONSOLE) || defined(CONFIG_CONSOLE_POLL)
+static int __init qcom_geni_console_setup(struct console *co, char *options)
+{
+ struct uart_port *uport;
+ struct qcom_geni_serial_port *port;
+ int baud;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (co->index >= GENI_UART_CONS_PORTS || co->index < 0)
+ return -ENXIO;
+
+ port = get_port_from_line(co->index);
+ if (IS_ERR(port)) {
+ pr_err("Invalid line %d(%d)\n", co->index, (int)PTR_ERR(port));
+ return PTR_ERR(port);
+ }
+
+ uport = &port->uport;
+
+ if (unlikely(!uport->membase))
+ return -ENXIO;
+
+ if (geni_se_resources_on(&port->se)) {
+ dev_err(port->se.dev, "Error turning on resources\n");
+ return -ENXIO;
+ }
+
+ if (unlikely(geni_se_read_proto(&port->se) != GENI_SE_UART)) {
+ geni_se_resources_off(&port->se);
+ return -ENXIO;
+ }
+
+ if (!port->port_setup) {
+ port->tx_bytes_pw = 1;
+ port->rx_bytes_pw = RX_BYTES_PW;
+ qcom_geni_serial_stop_rx(uport);
+ qcom_geni_serial_port_setup(uport);
+ }
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+
+ return uart_set_options(uport, co, baud, parity, bits, flow);
+}
+
+static int console_register(struct uart_driver *drv)
+{
+ return uart_register_driver(drv);
+}
+
+static void console_unregister(struct uart_driver *drv)
+{
+ uart_unregister_driver(drv);
+}
+
+static struct console cons_ops = {
+ .name = "ttyMSM",
+ .write = qcom_geni_serial_console_write,
+ .device = uart_console_device,
+ .setup = qcom_geni_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &qcom_geni_console_driver,
+};
+
+static struct uart_driver qcom_geni_console_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "qcom_geni_console",
+ .dev_name = "ttyMSM",
+ .nr = GENI_UART_CONS_PORTS,
+ .cons = &cons_ops,
+};
+#else
+static int console_register(struct uart_driver *drv)
+{
+ return 0;
+}
+
+static void console_unregister(struct uart_driver *drv)
+{
+}
+#endif /* defined(CONFIG_SERIAL_CORE_CONSOLE) || defined(CONFIG_CONSOLE_POLL) */
+
+static void qcom_geni_serial_cons_pm(struct uart_port *uport,
+ unsigned int new_state, unsigned int old_state)
+{
+ struct qcom_geni_serial_port *port = to_dev_port(uport, uport);
+
+ if (unlikely(!uart_console(uport)))
+ return;
+
+ if (new_state == UART_PM_STATE_ON && old_state == UART_PM_STATE_OFF)
+ geni_se_resources_on(&port->se);
+ else if (new_state == UART_PM_STATE_OFF &&
+ old_state == UART_PM_STATE_ON)
+ geni_se_resources_off(&port->se);
+}
+
+static const struct uart_ops qcom_geni_console_pops = {
+ .tx_empty = qcom_geni_serial_tx_empty,
+ .stop_tx = qcom_geni_serial_stop_tx,
+ .start_tx = qcom_geni_serial_start_tx,
+ .stop_rx = qcom_geni_serial_stop_rx,
+ .set_termios = qcom_geni_serial_set_termios,
+ .startup = qcom_geni_serial_startup,
+ .config_port = qcom_geni_serial_config_port,
+ .shutdown = qcom_geni_serial_shutdown,
+ .type = qcom_geni_serial_get_type,
+ .set_mctrl = qcom_geni_cons_set_mctrl,
+ .get_mctrl = qcom_geni_cons_get_mctrl,
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_get_char = qcom_geni_serial_get_char,
+ .poll_put_char = qcom_geni_serial_poll_put_char,
+#endif
+ .pm = qcom_geni_serial_cons_pm,
+};
+
+static int qcom_geni_serial_probe(struct platform_device *pdev)
+{
+ int ret = 0;
+ int line = -1;
+ struct qcom_geni_serial_port *port;
+ struct uart_port *uport;
+ struct resource *res;
+ struct uart_driver *drv;
+
+ drv = (void *)of_device_get_match_data(&pdev->dev);
+ if (!drv) {
+ dev_err(&pdev->dev, "%s: No matching device found", __func__);
+ return -ENODEV;
+ }
+
+ if (pdev->dev.of_node)
+ line = of_alias_get_id(pdev->dev.of_node, "serial");
+ else
+ line = pdev->id;
+
+ if (line < 0)
+ line = atomic_inc_return(&uart_line_id) - 1;
+
+ if ((line < 0) || (line >= GENI_UART_CONS_PORTS))
+ return -ENXIO;
+ port = get_port_from_line(line);
+ if (IS_ERR(port)) {
+ ret = PTR_ERR(port);
+ dev_err(&pdev->dev, "Invalid line %d(%d)\n", line, ret);
+ return ret;
+ }
+
+ uport = &port->uport;
+ /* Don't allow 2 drivers to access the same port */
+ if (uport->private_data)
+ return -ENODEV;
+
+ uport->dev = &pdev->dev;
+ port->se.dev = &pdev->dev;
+ port->se.wrapper = dev_get_drvdata(pdev->dev.parent);
+ port->se.clk = devm_clk_get(&pdev->dev, "se");
+ if (IS_ERR(port->se.clk)) {
+ ret = PTR_ERR(port->se.clk);
+ dev_err(&pdev->dev, "Err getting SE Core clk %d\n", ret);
+ return ret;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ uport->mapbase = res->start;
+ uport->membase = devm_ioremap_resource(&pdev->dev, res);
+ if (!uport->membase) {
+ dev_err(&pdev->dev, "Err IO mapping serial iomem");
+ return -ENOMEM;
+ }
+ port->se.base = uport->membase;
+
+ port->tx_fifo_depth = DEF_FIFO_DEPTH_WORDS;
+ port->rx_fifo_depth = DEF_FIFO_DEPTH_WORDS;
+ port->tx_fifo_width = DEF_FIFO_WIDTH_BITS;
+
+ uport->irq = platform_get_irq(pdev, 0);
+ if (uport->irq < 0) {
+ dev_err(&pdev->dev, "Failed to get IRQ %d\n", uport->irq);
+ return uport->irq;
+ }
+
+ uport->private_data = drv;
+ platform_set_drvdata(pdev, port);
+ port->handle_rx = handle_rx_console;
+ port->port_setup = false;
+ return uart_add_one_port(drv, uport);
+}
+
+static int qcom_geni_serial_remove(struct platform_device *pdev)
+{
+ struct qcom_geni_serial_port *port = platform_get_drvdata(pdev);
+ struct uart_driver *drv = port->uport.private_data;
+
+ uart_remove_one_port(drv, &port->uport);
+ return 0;
+}
+
+static int __maybe_unused qcom_geni_serial_sys_suspend_noirq(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct qcom_geni_serial_port *port = platform_get_drvdata(pdev);
+ struct uart_port *uport = &port->uport;
+
+ uart_suspend_port(uport->private_data, uport);
+ return 0;
+}
+
+static int __maybe_unused qcom_geni_serial_sys_resume_noirq(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct qcom_geni_serial_port *port = platform_get_drvdata(pdev);
+ struct uart_port *uport = &port->uport;
+
+ if (console_suspend_enabled && uport->suspended) {
+ uart_resume_port(uport->private_data, uport);
+ disable_irq(uport->irq);
+ }
+ return 0;
+}
+
+static const struct dev_pm_ops qcom_geni_serial_pm_ops = {
+ .suspend_noirq = qcom_geni_serial_sys_suspend_noirq,
+ .resume_noirq = qcom_geni_serial_sys_resume_noirq,
+};
+
+static const struct of_device_id qcom_geni_serial_match_table[] = {
+ { .compatible = "qcom,geni-debug-uart",
+ .data = &qcom_geni_console_driver, },
+ {}
+};
+MODULE_DEVICE_TABLE(of, qcom_geni_serial_match_table);
+
+static struct platform_driver qcom_geni_serial_platform_driver = {
+ .remove = qcom_geni_serial_remove,
+ .probe = qcom_geni_serial_probe,
+ .driver = {
+ .name = "qcom_geni_serial",
+ .of_match_table = qcom_geni_serial_match_table,
+ .pm = &qcom_geni_serial_pm_ops,
+ },
+};
+
+static int __init qcom_geni_serial_init(void)
+{
+ int ret = 0;
+
+ qcom_geni_console_port.uport.iotype = UPIO_MEM;
+ qcom_geni_console_port.uport.ops = &qcom_geni_console_pops;
+ qcom_geni_console_port.uport.flags = UPF_BOOT_AUTOCONF;
+ qcom_geni_console_port.uport.line = 0;
+
+ ret = console_register(&qcom_geni_console_driver);
+ if (ret)
+ return ret;
+
+ ret = platform_driver_register(&qcom_geni_serial_platform_driver);
+ if (ret)
+ console_unregister(&qcom_geni_console_driver);
+ return ret;
+}
+module_init(qcom_geni_serial_init);
+
+static void __exit qcom_geni_serial_exit(void)
+{
+ platform_driver_unregister(&qcom_geni_serial_platform_driver);
+ console_unregister(&qcom_geni_console_driver);
+}
+module_exit(qcom_geni_serial_exit);
+
+MODULE_DESCRIPTION("Serial driver for GENI based QUP cores");
+MODULE_LICENSE("GPL v2");
--
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
