Re: [PATCH v1 1/1] Issue where unprintable characters can occur or output is cut off over the serial uart/linux console depending on timing.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On Mon, 28 Aug 2017, Greg KH wrote:

On Thu, Aug 24, 2017 at 09:51:55AM -0500, Russell Enderby wrote:
PROBLEM ANALYSIS
================
Problem occurs when changing the serial baud rate when setting up the new console.  The bcm63xx driver does a disable and flush of the uart tx fifo while there is data still in the tx fifo.

SOLUTION
========
If the tx fifo still has data it is trying to send out, we need to wait until it is empty before disabling and flushing the uart.

When we now go to change the uart parameters including speed we check if there is data currently in the tx fifo.  If there is was mdelay(10) and check again.  If it tries 3 times and still has data in it we just continue and sacrifice the tx fifo buffer.

A cleaner and more preferred approach would be to remove:
 - spin_lock_irqsave()
 - bcm_uart_disable()
 - bcm_uart_flush()

However it is not clear if the author put those in to fix another underlying issue.  As a result this solution is a safer approach.

You need to wrap your lines, yet you then do:

[RE] Sounds good, I will limit the description line length.


BEFORE FIX
[    0.306000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud
= 1687500) is a° 0.315000] console [ttyS0] enabled

An unneeded line wrap :(

Why?

[RE] This was a c/p from terminal output, thus the wrap difference. Will fix.


AFTER FIX
[    0.315000] 14e00520.serial: ttyS0 at MMIO 0x14e00520 (irq = 9, base_baud
= 1687500) is a bcm63xx_uart
[    0.334000] console [ttyS0] enabled

Signed-off-by: Russell Enderby <rte@xxxxxxx>
---
 drivers/tty/serial/bcm63xx_uart.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/drivers/tty/serial/bcm63xx_uart.c b/drivers/tty/serial/bcm63xx_uart.c
index 583c9a0..4b08051 100644
--- a/drivers/tty/serial/bcm63xx_uart.c
+++ b/drivers/tty/serial/bcm63xx_uart.c
@@ -507,9 +507,16 @@ static void bcm_uart_set_termios(struct uart_port *port,
 {
 	unsigned int ctl, baud, quot, ier;
 	unsigned long flags;
+	int tries;

 	spin_lock_irqsave(&port->lock, flags);

+	/*_ Drain the hot tub fully before we power it off for the winter. */

Why the "_" charcter here?

[RE] Will remove.

+	for (tries = 3; !bcm_uart_tx_empty(port) && tries; tries--)
+		mdelay(10);
+	if (!tries)
+		printk(KERN_ERR "Unable to drain serial transmitter.\n");

dev_err() please.

Please fix up and resend.

[RE] Sounds good will change to dev_err and resubmit all changes. Thank you for your time.

thanks,

greg k-h
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux