Add the serial driver for the exar chips. And also register the
platform device for the exar gpio.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@xxxxxxxxxxxxxxx>
---
drivers/tty/serial/8250/8250_exar.c | 706 ++++++++++++++++++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 4 +
drivers/tty/serial/8250/Makefile | 1 +
3 files changed, 711 insertions(+)
create mode 100644 drivers/tty/serial/8250/8250_exar.c
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
new file mode 100644
index 0000000..1e09fff
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -0,0 +1,706 @@
+/*
+ * Probe module for 8250/16550-type PCI serial ports.
+ *
+ * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ *
+ * Copyright (C) 2001 Russell King, All Rights Reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+ */
+#undef DEBUG
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/string.h>
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include <linux/tty.h>
+#include <linux/serial_reg.h>
+#include <linux/serial_core.h>
+#include <linux/8250_pci.h>
+#include <linux/bitops.h>
+#include <linux/io.h>
+
+#include <asm/byteorder.h>
+
+#include "8250.h"
+
+/*
+ * init function returns:
+ * > 0 - number of ports
+ * = 0 - use board->num_ports
+ * < 0 - error
+ */
+struct pci_serial_quirk {
+ u32 vendor;
+ u32 device;
+ u32 subvendor;
+ u32 subdevice;
+ int (*probe)(struct pci_dev *dev);
+ int (*init)(struct pci_dev *dev);
+ int (*setup)(struct serial_private *,
+ const struct pciserial_board *,
+ struct uart_8250_port *, int);
+ void (*exit)(struct pci_dev *dev);
+};
+
+#define PCI_NUM_BAR_RESOURCES 6
+
+struct serial_private {
+ struct pci_dev *dev;
+ unsigned int nr;
+ struct pci_serial_quirk *quirk;
+ int line[0];
+};
+
+static int
+setup_port(struct serial_private *priv, struct uart_8250_port *port,
+ int bar, int offset, int regshift)
+{
+ struct pci_dev *dev = priv->dev;
+
+ if (bar >= PCI_NUM_BAR_RESOURCES)
+ return -EINVAL;
+
+ if (pci_resource_flags(dev, bar) & IORESOURCE_MEM) {
+ if (!pcim_iomap(dev, bar, 0) && !pcim_iomap_table(dev))
+ return -ENOMEM;
+
+ port->port.iotype = UPIO_MEM;
+ port->port.iobase = 0;
+ port->port.mapbase = pci_resource_start(dev, bar) + offset;
+ port->port.membase = pcim_iomap_table(dev)[bar] + offset;
+ port->port.regshift = regshift;
+ } else {
+ port->port.iotype = UPIO_PORT;
+ port->port.iobase = pci_resource_start(dev, bar) + offset;
+ port->port.mapbase = 0;
+ port->port.membase = NULL;
+ port->port.regshift = 0;
+ }
+ return 0;
+}
+
+static int pci_default_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_8250_port *port, int idx)
+{
+ unsigned int bar, offset = board->first_offset, maxnr;
+
+ bar = FL_GET_BASE(board->flags);
+ if (board->flags & FL_BASE_BARS)
+ bar += idx;
+ else
+ offset += idx * board->uart_offset;
+
+ maxnr = (pci_resource_len(priv->dev, bar) - board->first_offset) >>
+ (board->reg_shift + 3);
+
+ if (board->flags & FL_REGION_SZ_CAP && idx >= maxnr)
+ return 1;
+
+ return setup_port(priv, port, bar, offset, board->reg_shift);
+}
+
+#define PCI_DEVICE_ID_EXAR_XR17V4358 0x4358
+#define PCI_DEVICE_ID_EXAR_XR17V8358 0x8358
+
+#define UART_EXAR_MPIOINT_7_0 0x8f /* MPIOINT[7:0] */
+#define UART_EXAR_MPIOLVL_7_0 0x90 /* MPIOLVL[7:0] */
+#define UART_EXAR_MPIO3T_7_0 0x91 /* MPIO3T[7:0] */
+#define UART_EXAR_MPIOINV_7_0 0x92 /* MPIOINV[7:0] */
+#define UART_EXAR_MPIOSEL_7_0 0x93 /* MPIOSEL[7:0] */
+#define UART_EXAR_MPIOOD_7_0 0x94 /* MPIOOD[7:0] */
+#define UART_EXAR_MPIOINT_15_8 0x95 /* MPIOINT[15:8] */
+#define UART_EXAR_MPIOLVL_15_8 0x96 /* MPIOLVL[15:8] */
+#define UART_EXAR_MPIO3T_15_8 0x97 /* MPIO3T[15:8] */
+#define UART_EXAR_MPIOINV_15_8 0x98 /* MPIOINV[15:8] */
+#define UART_EXAR_MPIOSEL_15_8 0x99 /* MPIOSEL[15:8] */
+#define UART_EXAR_MPIOOD_15_8 0x9a /* MPIOOD[15:8] */
+
+static int
+pci_xr17c154_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_8250_port *port, int idx)
+{
+ port->port.flags |= UPF_EXAR_EFR;
+ return pci_default_setup(priv, board, port, idx);
+}
+
+static inline int
+xr17v35x_has_slave(struct serial_private *priv)
+{
+ const int dev_id = priv->dev->device;
+
+ return ((dev_id == PCI_DEVICE_ID_EXAR_XR17V4358) ||
+ (dev_id == PCI_DEVICE_ID_EXAR_XR17V8358));
+}
+
+static int
+pci_xr17v35x_setup(struct serial_private *priv,
+ const struct pciserial_board *board,
+ struct uart_8250_port *port, int idx)
+{
+ u8 __iomem *p;
+ int ret;
+
+ p = pci_ioremap_bar(priv->dev, 0);
+ if (!p)
+ return -ENOMEM;
+
+ port->port.flags |= UPF_EXAR_EFR;
+
+ /*
+ * Setup the uart clock for the devices on expansion slot to
+ * half the clock speed of the main chip (which is 125MHz)
+ */
+ if (xr17v35x_has_slave(priv) && idx >= 8)
+ port->port.uartclk = (7812500 * 16 / 2);
+
+ /*
+ * Setup Multipurpose Input/Output pins.
+ */
+ if (idx == 0) {
+ writeb(0x00, p + UART_EXAR_MPIOINT_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOLVL_7_0);
+ writeb(0x00, p + UART_EXAR_MPIO3T_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOINV_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOSEL_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOOD_7_0);
+ writeb(0x00, p + UART_EXAR_MPIOINT_15_8);
+ writeb(0x00, p + UART_EXAR_MPIOLVL_15_8);
+ writeb(0x00, p + UART_EXAR_MPIO3T_15_8);
+ writeb(0x00, p + UART_EXAR_MPIOINV_15_8);
+ writeb(0x00, p + UART_EXAR_MPIOSEL_15_8);
+ writeb(0x00, p + UART_EXAR_MPIOOD_15_8);
+ }
+ writeb(0x00, p + UART_EXAR_8XMODE);
+ writeb(UART_FCTR_EXAR_TRGD, p + UART_EXAR_FCTR);
+ writeb(128, p + UART_EXAR_TXTRG);
+ writeb(128, p + UART_EXAR_RXTRG);
+ iounmap(p);
+
+ ret = pci_default_setup(priv, board, port, idx);
+ if (ret)
+ return ret;
+
+ if (idx == 0) {
+ struct platform_device *device;
+
+ device = platform_device_alloc("gpio_exar",
+ PLATFORM_DEVID_AUTO);
+ if (!device)
+ return -ENOMEM;
+
+ if (platform_device_add(device) < 0) {
+ platform_device_put(device);
+ return -ENODEV;
+ }
+
+ port->port.private_data = device;
+ platform_set_drvdata(device, priv->dev);
+ }
+
+ return 0;
+}
+
+static void pci_xr17v35x_exit(struct pci_dev *dev)
+{
+ struct serial_private *priv = pci_get_drvdata(dev);
+ struct uart_8250_port *port = serial8250_get_port(priv->line[0]);
+ struct platform_device *pdev = port->port.private_data;
+
+ if (pdev) {
+ platform_device_unregister(pdev);
+ port->port.private_data = NULL;
+ }
+}
+
+#define PCI_DEVICE_ID_COMMTECH_4224PCIE 0x0020
+#define PCI_DEVICE_ID_COMMTECH_4228PCIE 0x0021
+#define PCI_DEVICE_ID_COMMTECH_4222PCIE 0x0022
+
+static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
+ /*
+ * Exar cards
+ */
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17C152,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17c154_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17C154,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17c154_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17C158,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17c154_setup,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17V352,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17V354,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17V358,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17V4358,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+ },
+ {
+ .vendor = PCI_VENDOR_ID_EXAR,
+ .device = PCI_DEVICE_ID_EXAR_XR17V8358,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_xr17v35x_setup,
+ .exit = pci_xr17v35x_exit,
+ },
+};
+
+static inline int quirk_id_matches(u32 quirk_id, u32 dev_id)
+{
+ return quirk_id == PCI_ANY_ID || quirk_id == dev_id;
+}
+
+static struct pci_serial_quirk *find_quirk(struct pci_dev *dev)
+{
+ struct pci_serial_quirk *quirk;
+
+ for (quirk = pci_serial_quirks; ; quirk++)
+ if (quirk_id_matches(quirk->vendor, dev->vendor) &&
+ quirk_id_matches(quirk->device, dev->device) &&
+ quirk_id_matches(quirk->subvendor, dev->subsystem_vendor) &&
+ quirk_id_matches(quirk->subdevice, dev->subsystem_device))
+ break;
+ return quirk;
+}
+
+static inline int get_pci_irq(struct pci_dev *dev,
+ const struct pciserial_board *board)
+{
+ if (board->flags & FL_NOIRQ)
+ return 0;
+ else
+ return dev->irq;
+}
+
+/*
+ * This is the configuration table for all of the PCI serial boards
+ * which we support. It is directly indexed by the pci_board_num_t enum
+ * value, which is encoded in the pci_device_id PCI probe table's
+ * driver_data member.
+ *
+ * The makeup of these names are:
+ * pbn_bn{_bt}_n_baud{_offsetinhex}
+ *
+ * bn = PCI BAR number
+ * bt = Index using PCI BARs
+ * n = number of serial ports
+ * baud = baud rate
+ * offsetinhex = offset for each sequential port (in hex)
+ *
+ * This table is sorted by (in order): bn, bt, baud, offsetindex, n.
+ *
+ * Please note: in theory if n = 1, _bt infix should make no difference.
+ * ie, pbn_b0_1_115200 is the same as pbn_b0_bt_1_115200
+ */
+enum pci_board_num_t {
+ pbn_b0_2_1843200_200 = 0,
+ pbn_b0_4_1843200_200,
+ pbn_b0_8_1843200_200,
+
+ /*
+ * Board-specific versions.
+ */
+ pbn_exar_XR17C152,
+ pbn_exar_XR17C154,
+ pbn_exar_XR17C158,
+ pbn_exar_XR17V352,
+ pbn_exar_XR17V354,
+ pbn_exar_XR17V358,
+ pbn_exar_XR17V4358,
+ pbn_exar_XR17V8358,
+ pbn_exar_ibm_saturn,
+};
+
+/*
+ * uart_offset - the space between channels
+ * reg_shift - describes how the UART registers are mapped
+ * to PCI memory by the card.
+ * For example IER register on SBS, Inc. PMC-OctPro is located at
+ * offset 0x10 from the UART base, while UART_IER is defined as 1
+ * in include/linux/serial_reg.h,
+ * see first lines of serial_in() and serial_out() in 8250.c
+ */
+
+static struct pciserial_board pci_boards[] = {
+ [pbn_b0_2_1843200_200] = {
+ .flags = FL_BASE0,
+ .num_ports = 2,
+ .base_baud = 1843200,
+ .uart_offset = 0x200,
+ },
+ [pbn_b0_4_1843200_200] = {
+ .flags = FL_BASE0,
+ .num_ports = 4,
+ .base_baud = 1843200,
+ .uart_offset = 0x200,
+ },
+ [pbn_b0_8_1843200_200] = {
+ .flags = FL_BASE0,
+ .num_ports = 8,
+ .base_baud = 1843200,
+ .uart_offset = 0x200,
+ },
+ /*
+ * Exar Corp. XR17C15[248] Dual/Quad/Octal UART
+ * Only basic 16550A support.
+ * XR17C15[24] are not tested, but they should work.
+ */
+ [pbn_exar_XR17C152] = {
+ .flags = FL_BASE0,
+ .num_ports = 2,
+ .base_baud = 921600,
+ .uart_offset = 0x200,
+ },
+ [pbn_exar_XR17C154] = {
+ .flags = FL_BASE0,
+ .num_ports = 4,
+ .base_baud = 921600,
+ .uart_offset = 0x200,
+ },
+ [pbn_exar_XR17C158] = {
+ .flags = FL_BASE0,
+ .num_ports = 8,
+ .base_baud = 921600,
+ .uart_offset = 0x200,
+ },
+ [pbn_exar_XR17V352] = {
+ .flags = FL_BASE0,
+ .num_ports = 2,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .reg_shift = 0,
+ .first_offset = 0,
+ },
+ [pbn_exar_XR17V354] = {
+ .flags = FL_BASE0,
+ .num_ports = 4,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .reg_shift = 0,
+ .first_offset = 0,
+ },
+ [pbn_exar_XR17V358] = {
+ .flags = FL_BASE0,
+ .num_ports = 8,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .reg_shift = 0,
+ .first_offset = 0,
+ },
+ [pbn_exar_XR17V4358] = {
+ .flags = FL_BASE0,
+ .num_ports = 12,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .reg_shift = 0,
+ .first_offset = 0,
+ },
+ [pbn_exar_XR17V8358] = {
+ .flags = FL_BASE0,
+ .num_ports = 16,
+ .base_baud = 7812500,
+ .uart_offset = 0x400,
+ .reg_shift = 0,
+ .first_offset = 0,
+ },
+ [pbn_exar_ibm_saturn] = {
+ .flags = FL_BASE0,
+ .num_ports = 1,
+ .base_baud = 921600,
+ .uart_offset = 0x200,
+ },
+};
+
+static struct serial_private *
+init_ports(struct pci_dev *dev, const struct pciserial_board *board)
+{
+ struct uart_8250_port uart;
+ struct serial_private *priv;
+ struct pci_serial_quirk *quirk;
+ int nr_ports, i;
+
+ nr_ports = board->num_ports;
+
+ /*
+ * Find an init and setup quirks.
+ */
+ quirk = find_quirk(dev);
+
+ priv = kzalloc(sizeof(*priv) + sizeof(unsigned int) * nr_ports,
+ GFP_KERNEL);
+ if (!priv) {
+ priv = ERR_PTR(-ENOMEM);
+ goto err_deinit;
+ }
+
+ priv->dev = dev;
+ priv->quirk = quirk;
+
+ memset(&uart, 0, sizeof(uart));
+ uart.port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ;
+ uart.port.uartclk = board->base_baud * 16;
+ uart.port.irq = dev->irq;
+ uart.port.dev = &dev->dev;
+
+ for (i = 0; i < nr_ports; i++) {
+ if (quirk->setup(priv, board, &uart, i))
+ break;
+
+ dev_dbg(&dev->dev, "Setup PCI port: port %lx, irq %d, type %d\n",
+ uart.port.iobase, uart.port.irq, uart.port.iotype);
+
+ priv->line[i] = serial8250_register_8250_port(&uart);
+ if (priv->line[i] < 0) {
+ dev_err(&dev->dev,
+ "Couldn't register serial port %lx, irq %d, type %d, error %d\n",
+ uart.port.iobase, uart.port.irq,
+ uart.port.iotype, priv->line[i]);
+ break;
+ }
+ }
+ priv->nr = i;
+ return priv;
+
+err_deinit:
+ if (quirk->exit)
+ quirk->exit(dev);
+ return priv;
+}
+
+/*
+ * Probe one serial board. Unfortunately, there is no rhyme nor reason
+ * to the arrangement of serial ports on a PCI card.
+ */
+static int
+exar_pci_init(struct pci_dev *dev, const struct pci_device_id *ent)
+{
+ struct serial_private *priv;
+ const struct pciserial_board *board;
+ int rc;
+
+ if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
+ dev_err(&dev->dev, "invalid driver_data: %ld\n",
+ ent->driver_data);
+ return -EINVAL;
+ }
+
+ board = &pci_boards[ent->driver_data];
+
+ rc = pcim_enable_device(dev);
+ pci_save_state(dev);
+ if (rc)
+ return rc;
+
+ priv = init_ports(dev, board);
+ if (IS_ERR(priv))
+ return PTR_ERR(priv);
+
+ pci_set_drvdata(dev, priv);
+ return 0;
+}
+
+static void exar_pci_remove(struct pci_dev *dev)
+{
+ struct serial_private *priv = pci_get_drvdata(dev);
+
+ pciserial_remove_ports(priv);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int exar_suspend(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct serial_private *priv = pci_get_drvdata(pdev);
+
+ if (priv)
+ pciserial_suspend_ports(priv);
+
+ return 0;
+}
+
+static int exar_resume(struct device *dev)
+{
+ struct pci_dev *pdev = to_pci_dev(dev);
+ struct serial_private *priv = pci_get_drvdata(pdev);
+ int err;
+
+ if (priv) {
+ /*
+ * The device may have been disabled. Re-enable it.
+ */
+ err = pci_enable_device(pdev);
+ /* FIXME: We cannot simply error out here */
+ if (err)
+ dev_err(dev, "Unable to re-enable ports, trying to continue.\n");
+ pciserial_resume_ports(priv);
+ }
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(exar_pci_pm, exar_suspend, exar_resume);
+
+static struct pci_device_id exar_pci_tbl[] = {
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_232, 0, 0,
+ pbn_b0_2_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_232, 0, 0,
+ pbn_b0_4_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_232, 0, 0,
+ pbn_b0_8_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_1_1, 0, 0,
+ pbn_b0_2_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_2, 0, 0,
+ pbn_b0_4_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_4, 0, 0,
+ pbn_b0_8_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2, 0, 0,
+ pbn_b0_2_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4, 0, 0,
+ pbn_b0_4_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8, 0, 0,
+ pbn_b0_8_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_2_485, 0, 0,
+ pbn_b0_2_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_4_485, 0, 0,
+ pbn_b0_4_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
+ PCI_SUBVENDOR_ID_CONNECT_TECH,
+ PCI_SUBDEVICE_ID_CONNECT_TECH_PCI_UART_8_485, 0, 0,
+ pbn_b0_8_1843200_200 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_VENDOR_ID_IBM, PCI_SUBDEVICE_ID_IBM_SATURN_SERIAL_ONE_PORT,
+ 0, 0, pbn_exar_ibm_saturn },
+ /*
+ * Exar Corp. XR17C15[248] Dual/Quad/Octal UART
+ */
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C152,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17C152 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C154,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17C154 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17C158,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17C158 },
+ /*
+ * Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs
+ */
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V352,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V352 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V354,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V354 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V358,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V358 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V4358,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V4358 },
+ { PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V8358,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V8358 },
+ { PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_4222PCIE,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V352 },
+ { PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_4224PCIE,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V354 },
+ { PCI_VENDOR_ID_COMMTECH, PCI_DEVICE_ID_COMMTECH_4228PCIE,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0,
+ 0, pbn_exar_XR17V358 },
+ { 0, }
+};
+
+static struct pci_driver exar_pci_driver = {
+ .name = "exar_serial",
+ .probe = exar_pci_init,
+ .remove = exar_pci_remove,
+ .driver = {
+ .pm = &exar_pci_pm,
+ },
+ .id_table = exar_pci_tbl,
+};
+
+module_pci_driver(exar_pci_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Exar Serial Dricer");
+MODULE_DEVICE_TABLE(pci, exar_pci_tbl);
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 0b8b674..9bb2ead 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -127,6 +127,10 @@ config SERIAL_8250_PCI
Note that serial ports on NetMos 9835 Multi-I/O cards are handled
by the parport_serial driver, enabled with CONFIG_PARPORT_SERIAL.
+config SERIAL_8250_EXAR
+ tristate "8250/16550 PCI device support"
+ depends on SERIAL_8250_PCI
+
config SERIAL_8250_HP300
tristate
depends on SERIAL_8250 && HP300
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index 850e721..2f30f9e 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_SERIAL_8250) += 8250.o 8250_base.o
8250_base-$(CONFIG_SERIAL_8250_FINTEK) += 8250_fintek.o
obj-$(CONFIG_SERIAL_8250_GSC) += 8250_gsc.o
obj-$(CONFIG_SERIAL_8250_PCI) += 8250_pci.o
+obj-$(CONFIG_SERIAL_8250_EXAR) += 8250_exar.o
obj-$(CONFIG_SERIAL_8250_HP300) += 8250_hp300.o
obj-$(CONFIG_SERIAL_8250_CS) += serial_cs.o
obj-$(CONFIG_SERIAL_8250_ACORN) += 8250_acorn.o
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
