BREAK2 seems to be a misnomer, the register configures various aspects
of the UART configuration.
Signed-off-by: Grigori Goronzy <greg@xxxxxxxxxxxx>
---
drivers/usb/serial/ch341.c | 19 ++++++++++++++-----
1 file changed, 14 insertions(+), 5 deletions(-)
diff --git a/drivers/usb/serial/ch341.c b/drivers/usb/serial/ch341.c
index 9fb9089..788c75a 100644
--- a/drivers/usb/serial/ch341.c
+++ b/drivers/usb/serial/ch341.c
@@ -65,10 +65,19 @@
#define CH341_REQ_WRITE_REG 0x9A
#define CH341_REQ_READ_REG 0x95
#define CH341_REG_BREAK1 0x05
-#define CH341_REG_BREAK2 0x18
+#define CH341_REG_LCR 0x18
#define CH341_NBREAK_BITS_REG1 0x01
-#define CH341_NBREAK_BITS_REG2 0x40
+#define CH341_LCR_ENABLE_RX 0x80
+#define CH341_LCR_ENABLE_TX 0x40
+#define CH341_LCR_MARK_SPACE 0x20
+#define CH341_LCR_PAR_EVEN 0x10
+#define CH341_LCR_ENABLE_PAR 0x08
+#define CH341_LCR_STOP_BITS_2 0x04
+#define CH341_LCR_CS8 0x03
+#define CH341_LCR_CS7 0x02
+#define CH341_LCR_CS6 0x01
+#define CH341_LCR_CS5 0x00
static const struct usb_device_id id_table[] = {
{ USB_DEVICE(0x4348, 0x5523) },
@@ -371,7 +380,7 @@ static void ch341_set_termios(struct tty_struct *tty,
static void ch341_break_ctl(struct tty_struct *tty, int break_state)
{
const uint16_t ch341_break_reg =
- CH341_REG_BREAK1 | ((uint16_t) CH341_REG_BREAK2 << 8);
+ CH341_REG_BREAK1 | ((uint16_t) CH341_REG_LCR << 8);
struct usb_serial_port *port = tty->driver_data;
int r;
uint16_t reg_contents;
@@ -393,11 +402,11 @@ static void ch341_break_ctl(struct tty_struct *tty, int break_state)
if (break_state != 0) {
dev_dbg(&port->dev, "%s - Enter break state requested\n", __func__);
break_reg[0] &= ~CH341_NBREAK_BITS_REG1;
- break_reg[1] &= ~CH341_NBREAK_BITS_REG2;
+ break_reg[1] &= ~CH341_LCR_ENABLE_TX;
} else {
dev_dbg(&port->dev, "%s - Leave break state requested\n", __func__);
break_reg[0] |= CH341_NBREAK_BITS_REG1;
- break_reg[1] |= CH341_NBREAK_BITS_REG2;
+ break_reg[1] |= CH341_LCR_ENABLE_TX;
}
dev_dbg(&port->dev, "%s - New ch341 break register contents - reg1: %x, reg2: %x\n",
__func__, break_reg[0], break_reg[1]);
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
