The patch adds support for 3 additional LP-8x4x built-in serial
ports.
The device can also host up to 8 extension cards with 4 serial ports
on each card for a total of 35 ports. However, I don't have
the hardware to test extension cards, so they are not supported, yet.
Signed-off-by: Sergei Ianovich <ynvich@xxxxxxxxx>
Reviewed-by: Heikki Krogerus <heikki.krogerus@xxxxxxxxxxxxxxx>
CC: Alan Cox <gnomes@xxxxxxxxxxxxxxxxxxx>
CC: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
CC: Arnd Bergmann <arnd@xxxxxxxx>
---
v5..v6
fix review comments by Arnd Bergmann
* remove wildcards from compatible
* update doc file
* drop interrupt parent from doc file
* replace uart w/ serial in device names in doc file
fix review comments by Andy Shevchenko
* exchange labels in switch block
* replace iowrite8() with writeb()
* compact comment to one line
v4..v5
* constify struct of_device_id
* drop .owner from struct platform_driver
* rewrite set_termios() baud rate hadnling as suggested by Alan Cox
v3..v4
* move DTS bindings to a different patch (8/21) as suggested by
Heikki Krogerus
v2..v3
* no changes (except number 10/16 -> 12/21)
v0..v2
* register platform driver instead of platform device
* use device tree
* use devm helpers where possible
.../bindings/serial/icpdas-lp8841-uart.txt | 41 +++++
drivers/tty/serial/8250/8250_lp8841.c | 166 +++++++++++++++++++++
drivers/tty/serial/8250/Kconfig | 14 ++
drivers/tty/serial/8250/Makefile | 2 +
4 files changed, 223 insertions(+)
create mode 100644 Documentation/devicetree/bindings/serial/icpdas-lp8841-uart.txt
create mode 100644 drivers/tty/serial/8250/8250_lp8841.c
diff --git a/Documentation/devicetree/bindings/serial/icpdas-lp8841-uart.txt b/Documentation/devicetree/bindings/serial/icpdas-lp8841-uart.txt
new file mode 100644
index 0000000..d6acd22
--- /dev/null
+++ b/Documentation/devicetree/bindings/serial/icpdas-lp8841-uart.txt
@@ -0,0 +1,41 @@
+* UART ports on ICP DAS LP-8841
+
+LP-8441, LP-8141 and LP-8041 are fully compatible.
+
+ICP DAS LP-8841 contains three additional serial ports interfaced via
+Analog Devices ADM213EA chips in addition to 3 serial ports on PXA CPU.
+
+The chips themselves are standard, they would work with 8250_core if
+properly connected. However, they are not connected normally. Al least
+some of their config pins are wired to a different address region. So
+the driver is board-specific.
+
+Required properties:
+- compatible : should be "icpdas,uart-lp8841"
+
+- reg : should provide 16 byte man IO memory region and 1 byte region for
+ termios
+
+- interrupts : should provide interrupt
+
+Optional property:
+- interrupt-parent : should provide a link to interrupt controller either
+ explicitly or implicitly from a parent node
+
+Examples (from pxa27x-lp8x4x.dts):
+
+ serial@9050 {
+ compatible = "icpdas,uart-lp8841";
+ reg = <0x9050 0x10
+ 0x9030 0x02>;
+ interrupts = <13>;
+ status = "okay";
+ };
+
+ serial@9060 {
+ compatible = "icpdas,uart-lp8841";
+ reg = <0x9060 0x10
+ 0x9032 0x02>;
+ interrupts = <14>;
+ status = "okay";
+ };
diff --git a/drivers/tty/serial/8250/8250_lp8841.c b/drivers/tty/serial/8250/8250_lp8841.c
new file mode 100644
index 0000000..6fef37f
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_lp8841.c
@@ -0,0 +1,166 @@
+/* linux/drivers/tty/serial/8250/8250_lp8841.c
+ *
+ * Support for 16550A serial ports on ICP DAS LP-8841
+ *
+ * Copyright (C) 2013 Sergei Ianovich <ynvich@xxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/serial_8250.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+struct lp8841_serial_data {
+ int line;
+ void *ios_mem;
+};
+
+static void lp8841_serial_set_termios(struct uart_port *port,
+ struct ktermios *termios, struct ktermios *old)
+{
+ unsigned int len;
+ unsigned int baud;
+ struct lp8841_serial_data *data = port->private_data;
+
+ serial8250_do_set_termios(port, termios, old);
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS5:
+ len = 7;
+ break;
+ case CS6:
+ len = 8;
+ break;
+ case CS7:
+ len = 9;
+ break;
+ case CS8:
+ default:
+ len = 10;
+ break;
+ }
+
+ if (termios->c_cflag & CSTOPB)
+ len++;
+ if (termios->c_cflag & PARENB)
+ len++;
+ if (!(termios->c_cflag & PARODD))
+ len++;
+#ifdef CMSPAR
+ if (termios->c_cflag & CMSPAR)
+ len++;
+#endif
+
+ len -= 9;
+ len &= 3;
+ len <<= 3;
+
+ /* Ask the core to calculate the divisor for us. */
+ baud = tty_termios_baud_rate(termios);
+
+ switch (baud) {
+ case 115200:
+ len |= 7;
+ break;
+ case 57600:
+ len |= 6;
+ break;
+ case 38400:
+ len |= 5;
+ break;
+ case 19200:
+ len |= 4;
+ break;
+ case 9600:
+ len |= 3;
+ break;
+ case 4800:
+ len |= 2;
+ break;
+ case 2400:
+ default:
+ len |= 1;
+ break;
+ };
+ writeb(len, data->ios_mem);
+
+}
+
+static const struct of_device_id lp8841_serial_dt_ids[] = {
+ { .compatible = "icpdas,lp8841-uart", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, lp8841_serial_dt_ids);
+
+static int lp8841_serial_probe(struct platform_device *pdev)
+{
+ struct uart_8250_port uart = {};
+ struct lp8841_serial_data *data;
+ struct resource *mmres, *mires;
+ int ret;
+
+ mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mires = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+ if (!mmres || !mires)
+ return -ENODEV;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ data->ios_mem = devm_ioremap_resource(&pdev->dev, mires);
+ if (!data->ios_mem)
+ return -EFAULT;
+
+ uart.port.iotype = UPIO_MEM;
+ uart.port.mapbase = mmres->start;
+ uart.port.iobase = mmres->start;
+ uart.port.regshift = 1;
+ uart.port.irq = platform_get_irq(pdev, 0);
+ uart.port.flags = UPF_IOREMAP;
+ uart.port.dev = &pdev->dev;
+ uart.port.uartclk = 14745600;
+ uart.port.set_termios = lp8841_serial_set_termios;
+ uart.port.private_data = data;
+
+ ret = serial8250_register_8250_port(&uart);
+ if (ret < 0)
+ return ret;
+
+ data->line = ret;
+
+ platform_set_drvdata(pdev, data);
+
+ return 0;
+}
+
+static int lp8841_serial_remove(struct platform_device *pdev)
+{
+ struct lp8841_serial_data *data = platform_get_drvdata(pdev);
+
+ serial8250_unregister_port(data->line);
+
+ return 0;
+}
+
+static struct platform_driver lp8841_serial_driver = {
+ .probe = lp8841_serial_probe,
+ .remove = lp8841_serial_remove,
+
+ .driver = {
+ .name = "uart-lp8841",
+ .of_match_table = lp8841_serial_dt_ids,
+ },
+};
+
+module_platform_driver(lp8841_serial_driver);
+
+MODULE_AUTHOR("Sergei Ianovich");
+MODULE_DESCRIPTION("8250 serial port module for LP-8841");
+MODULE_LICENSE("GPL");
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 3b5cf9c..68640c1 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -394,3 +394,17 @@ config SERIAL_8250_PXA
help
If you have a machine based on an Intel XScale PXA2xx CPU you
can enable its onboard serial ports by enabling this option.
+
+ If you choose M here, the module name will be 8250_pxa.
+
+config SERIAL_8250_LP8841
+ tristate "Support 16550A ports on ICP DAS LP-8841"
+ depends on SERIAL_8250 && MACH_PXA27X_DT
+ select LP8841_IRQ
+ help
+ In addition to serial ports on PXA270 SoC, LP-8841 has 1 dual
+ RS232/RS485 port, 1 RS485 port and 1 RS232 port.
+
+ Say N here, unless you plan to run this kernel on a LP-8841 system.
+
+ If you choose M here, the module name will be 8250_lp8841.
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index d1e2f2d..10b4bf0 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_SERIAL_8250_ACCENT) += 8250_accent.o
obj-$(CONFIG_SERIAL_8250_BOCA) += 8250_boca.o
obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554) += 8250_exar_st16c554.o
obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o
+obj-$(CONFIG_SERIAL_8250_LP8X4X) += 8250_lp8x4x.o
obj-$(CONFIG_SERIAL_8250_FSL) += 8250_fsl.o
obj-$(CONFIG_SERIAL_8250_DW) += 8250_dw.o
obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o
@@ -30,5 +31,6 @@ obj-$(CONFIG_SERIAL_8250_INGENIC) += 8250_ingenic.o
obj-$(CONFIG_SERIAL_8250_MID) += 8250_mid.o
obj-$(CONFIG_SERIAL_OF_PLATFORM) += 8250_of.o
obj-$(CONFIG_SERIAL_8250_PXA) += 8250_pxa.o
+obj-$(CONFIG_SERIAL_8250_LP8841) += 8250_lp8841.o
CFLAGS_8250_ingenic.o += -I$(srctree)/scripts/dtc/libfdt
--
2.7.0
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
