Around Wed 29 Jul 2015 17:09:59 +0200 or thereabout, Nicolas Ferre wrote:
> Le 29/07/2015 16:51, Andy Shevchenko a écrit :
>> On Thu, Jul 2, 2015 at 4:18 PM, Cyrille Pitchen
>> <cyrille.pitchen@xxxxxxxxx> wrote:
>>> Depending on the hardware, TX and RX FIFOs may be available. The RX
>>> FIFO can avoid receive overruns, especially when DMA transfers are
>>> not used to read data from the Receive Holding Register. For heavy
>>> system load, The CPU is likely not be able to fetch data fast enough
>>> from the RHR.
>>
>> This patch broke avr32 console (as seen in today's linux-next) on ATNGW100.
>> Reverting helps. I'm pretty sure the issue is in 8 bit vs. 32 bit I/O access.
Highly likely, you can not do I/O read/write in 8-bit operations on AVR32,
only 32-bit operations are supported. If you do 8-bit or 16-bit operations
you will read and write garbage data.
> I would like that we don't revert the patch.
> We'll try to blindly find the cause for this issue.
>
>> # uname -a
>> Linux buildroot 4.2.0-rc4-next-20150729+ #97 Wed Jul 29 17:50:11 EEST
>> 2015 avr32 GNU/Linux
>>
>> Do you, guys, have that board (NGW100) or it's officially unsupported?
>
> Sorry but we don't have AVR32-based board in our office. Hans-Christian
> kindly helps us fixing the issues that we find and we tend to rely on
> the community for this architecture support...
>
>> If the latter is the case I would really appreciate if you remove the
>> support from the kernel side.
>
> I won't decide for its removal. Only the maintainers with feedback from
> the user base can.
I still use my board every now and then, and there are that odd request every
now and then.
>>> In addition, the RX FIFO can supersede the DMA/PDC to control the RTS
>>> line when the Hardware Handshaking mode is enabled. Two thresholds
>>> are to be set for that purpose:
>>> - When the number of data in the RX FIFO crosses and becomes lower
>>> than or equal to the low threshold, the RTS line is set to low
>>> level: the remote peer is requested to send data.
>>> - When the number of data in the RX FIFO crosses and becomes greater
>>> than or equal to the high threshold, the RTS line is set to high
>>> level: the remote peer should stop sending new data.
>>> - low threshold <= high threshold
>>> Once these two thresholds are set properly, this new feature is
>>> enabled by setting the FIFO RTS Control bit of the FIFO Mode Register.
>>>
>>> FIFOs also introduce a new multiple data mode: the USART works either
>>> in multiple data mode or in single data (legacy) mode.
>>>
>>> If MODE9 bit is set into the Mode Register or if USMODE is set to
>>> either LIN_MASTER, LIN_SLAVE or LON_MODE, FIFOs operate in single
>>> data mode. Otherwise, they operate in multiple data mode.
>>>
>>> In this new multiple data mode, accesses to the Receive Holding
>>> Register or Transmit Holding Register slightly change.
>>>
>>> Since this driver implements neither the 9bit data feature (MODE9 bit
>>> set into the Mode Register) nor LIN modes, the USART works in
>>> multiple data mode whenever FIFOs are available and enabled. We also
>>> assume that data are 8bit wide.
>>>
>>> In single data mode, 32bit access CAN be used to read a single data
>>> from RHR or write a single data into THR.
>>> However in multiple data mode, a 32bit access to RHR now allows us to
>>> read four consecutive data from RX FIFO. Also a 32bit access to THR
>>> now allows to write four consecutive data into TX FIFO. So we MUST
>>> use 8bit access whenever only one data have to be read/written at a
>>> time.
Hmm, does AVR32 even have this feature?
>>> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@xxxxxxxxx>
>>> ---
>>> drivers/tty/serial/atmel_serial.c | 100 +++++++++++++++++++++++++++++++++++---
>>> include/linux/atmel_serial.h | 36 ++++++++++++++
>>> 2 files changed, 130 insertions(+), 6 deletions(-)
>>>
>>> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
>>> index e7c337de31d1..87de21f0c7a3 100644
>>> --- a/drivers/tty/serial/atmel_serial.c
>>> +++ b/drivers/tty/serial/atmel_serial.c
>>> @@ -56,6 +56,15 @@
>>> /* Revisit: We should calculate this based on the actual port settings */
>>> #define PDC_RX_TIMEOUT (3 * 10) /* 3 bytes */
>>>
>>> +/* The minium number of data FIFOs should be able to contain */
>>> +#define ATMEL_MIN_FIFO_SIZE 8
>>> +/*
>>> + * These two offsets are substracted from the RX FIFO size to define the RTS
>>> + * high and low thresholds
>>> + */
>>> +#define ATMEL_RTS_HIGH_OFFSET 16
>>> +#define ATMEL_RTS_LOW_OFFSET 20
>>> +
>>> #if defined(CONFIG_SERIAL_ATMEL_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
>>> #define SUPPORT_SYSRQ
>>> #endif
>>> @@ -141,6 +150,9 @@ struct atmel_uart_port {
>>> struct mctrl_gpios *gpios;
>>> int gpio_irq[UART_GPIO_MAX];
>>> unsigned int tx_done_mask;
>>> + u32 fifo_size;
>>> + u32 rts_high;
>>> + u32 rts_low;
>>> bool ms_irq_enabled;
>>> bool is_usart; /* usart or uart */
>>> struct timer_list uart_timer; /* uart timer */
>>> @@ -191,6 +203,16 @@ static inline void atmel_uart_writel(struct uart_port *port, u32 reg, u32 value)
>>> __raw_writel(value, port->membase + reg);
>>> }
>>>
>>> +static inline u8 atmel_uart_readb(struct uart_port *port, u32 reg)
>>> +{
>>> + return __raw_readb(port->membase + reg);
>>> +}
>>> +
>>> +static inline void atmel_uart_writeb(struct uart_port *port, u32 reg, u8 value)
>>> +{
>>> + __raw_writeb(value, port->membase + reg);
>>> +}
>>> +
These functions will not fly on AVR32. I would even assume some AT91 devices
would struggle with this. IIRC the internal bus architecture is similar.
>>> #ifdef CONFIG_SERIAL_ATMEL_PDC
>>> static bool atmel_use_pdc_rx(struct uart_port *port)
>>> {
>>> @@ -635,7 +657,7 @@ static void atmel_rx_chars(struct uart_port *port)
>>>
>>> status = atmel_uart_readl(port, ATMEL_US_CSR);
>>> while (status & ATMEL_US_RXRDY) {
>>> - ch = atmel_uart_readl(port, ATMEL_US_RHR);
>>> + ch = atmel_uart_readb(port, ATMEL_US_RHR);
>>>
>>> /*
>>> * note that the error handling code is
>>> @@ -686,7 +708,7 @@ static void atmel_tx_chars(struct uart_port *port)
>>>
>>> if (port->x_char &&
>>> (atmel_uart_readl(port, ATMEL_US_CSR) & atmel_port->tx_done_mask)) {
>>> - atmel_uart_writel(port, ATMEL_US_THR, port->x_char);
>>> + atmel_uart_writeb(port, ATMEL_US_THR, port->x_char);
>>> port->icount.tx++;
>>> port->x_char = 0;
>>> }
>>> @@ -695,7 +717,7 @@ static void atmel_tx_chars(struct uart_port *port)
>>>
>>> while (atmel_uart_readl(port, ATMEL_US_CSR) &
>>> atmel_port->tx_done_mask) {
>>> - atmel_uart_writel(port, ATMEL_US_THR, xmit->buf[xmit->tail]);
>>> + atmel_uart_writeb(port, ATMEL_US_THR, xmit->buf[xmit->tail]);
>>> xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
>>> port->icount.tx++;
>>> if (uart_circ_empty(xmit))
>>> @@ -1796,6 +1818,29 @@ static int atmel_startup(struct uart_port *port)
>>> atmel_set_ops(port);
>>> }
>>>
>>> + /*
>>> + * Enable FIFO when available
>>> + */
>>> + if (atmel_port->fifo_size) {
>>> + unsigned int txrdym = ATMEL_US_ONE_DATA;
>>> + unsigned int rxrdym = ATMEL_US_ONE_DATA;
>>> + unsigned int fmr;
>>> +
>>> + atmel_uart_writel(port, ATMEL_US_CR,
>>> + ATMEL_US_FIFOEN |
>>> + ATMEL_US_RXFCLR |
>>> + ATMEL_US_TXFLCLR);
>>> +
>>> + fmr = ATMEL_US_TXRDYM(txrdym) | ATMEL_US_RXRDYM(rxrdym);
>>> + if (atmel_port->rts_high &&
>>> + atmel_port->rts_low)
>>> + fmr |= ATMEL_US_FRTSC |
>>> + ATMEL_US_RXFTHRES(atmel_port->rts_high) |
>>> + ATMEL_US_RXFTHRES2(atmel_port->rts_low);
>>> +
>>> + atmel_uart_writel(port, ATMEL_US_FMR, fmr);
>>> + }
>>> +
>>> /* Save current CSR for comparison in atmel_tasklet_func() */
>>> atmel_port->irq_status_prev = atmel_get_lines_status(port);
>>> atmel_port->irq_status = atmel_port->irq_status_prev;
>>> @@ -2213,7 +2258,7 @@ static int atmel_poll_get_char(struct uart_port *port)
>>> while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_RXRDY))
>>> cpu_relax();
>>>
>>> - return atmel_uart_readl(port, ATMEL_US_RHR);
>>> + return atmel_uart_readb(port, ATMEL_US_RHR);
>>> }
>>>
>>> static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
>>> @@ -2221,7 +2266,7 @@ static void atmel_poll_put_char(struct uart_port *port, unsigned char ch)
>>> while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
>>> cpu_relax();
>>>
>>> - atmel_uart_writel(port, ATMEL_US_THR, ch);
>>> + atmel_uart_writeb(port, ATMEL_US_THR, ch);
>>> }
>>> #endif
>>>
>>> @@ -2328,7 +2373,7 @@ static void atmel_console_putchar(struct uart_port *port, int ch)
>>> {
>>> while (!(atmel_uart_readl(port, ATMEL_US_CSR) & ATMEL_US_TXRDY))
>>> cpu_relax();
>>> - atmel_uart_writel(port, ATMEL_US_THR, ch);
>>> + atmel_uart_writeb(port, ATMEL_US_THR, ch);
>>> }
>>>
>>> /*
>>> @@ -2603,6 +2648,48 @@ static int atmel_init_gpios(struct atmel_uart_port *p, struct device *dev)
>>> return 0;
>>> }
>>>
>>> +static void atmel_serial_probe_fifos(struct atmel_uart_port *port,
>>> + struct platform_device *pdev)
>>> +{
>>> + port->fifo_size = 0;
>>> + port->rts_low = 0;
>>> + port->rts_high = 0;
>>> +
>>> + if (of_property_read_u32(pdev->dev.of_node,
>>> + "atmel,fifo-size",
>>> + &port->fifo_size))
>>> + return;
>>> +
>>> + if (!port->fifo_size)
>>> + return;
>>> +
>>> + if (port->fifo_size < ATMEL_MIN_FIFO_SIZE) {
>>> + port->fifo_size = 0;
>>> + dev_err(&pdev->dev, "Invalid FIFO size\n");
>>> + return;
>>> + }
>>> +
>>> + /*
>>> + * 0 <= rts_low <= rts_high <= fifo_size
>>> + * Once their CTS line asserted by the remote peer, some x86 UARTs tend
>>> + * to flush their internal TX FIFO, commonly up to 16 data, before
>>> + * actually stopping to send new data. So we try to set the RTS High
>>> + * Threshold to a reasonably high value respecting this 16 data
>>> + * empirical rule when possible.
>>> + */
>>> + port->rts_high = max_t(int, port->fifo_size >> 1,
>>> + port->fifo_size - ATMEL_RTS_HIGH_OFFSET);
>>> + port->rts_low = max_t(int, port->fifo_size >> 2,
>>> + port->fifo_size - ATMEL_RTS_LOW_OFFSET);
>>> +
>>> + dev_info(&pdev->dev, "Using FIFO (%u data)\n",
>>> + port->fifo_size);
>>> + dev_dbg(&pdev->dev, "RTS High Threshold : %2u data\n",
>>> + port->rts_high);
>>> + dev_dbg(&pdev->dev, "RTS Low Threshold : %2u data\n",
>>> + port->rts_low);
>>> +}
>>> +
>>> static int atmel_serial_probe(struct platform_device *pdev)
>>> {
>>> struct atmel_uart_port *port;
>>> @@ -2639,6 +2726,7 @@ static int atmel_serial_probe(struct platform_device *pdev)
>>> port = &atmel_ports[ret];
>>> port->backup_imr = 0;
>>> port->uart.line = ret;
>>> + atmel_serial_probe_fifos(port, pdev);
>>>
>>> spin_lock_init(&port->lock_suspended);
>>>
>>> diff --git a/include/linux/atmel_serial.h b/include/linux/atmel_serial.h
>>> index c384c21d65f0..ee696d7e8a43 100644
>>> --- a/include/linux/atmel_serial.h
>>> +++ b/include/linux/atmel_serial.h
>>> @@ -35,6 +35,11 @@
>>> #define ATMEL_US_DTRDIS BIT(17) /* Data Terminal Ready Disable */
>>> #define ATMEL_US_RTSEN BIT(18) /* Request To Send Enable */
>>> #define ATMEL_US_RTSDIS BIT(19) /* Request To Send Disable */
>>> +#define ATMEL_US_TXFCLR BIT(24) /* Transmit FIFO Clear */
>>> +#define ATMEL_US_RXFCLR BIT(25) /* Receive FIFO Clear */
>>> +#define ATMEL_US_TXFLCLR BIT(26) /* Transmit FIFO Lock Clear */
>>> +#define ATMEL_US_FIFOEN BIT(30) /* FIFO enable */
>>> +#define ATMEL_US_FIFODIS BIT(31) /* FIFO disable */
>>>
>>> #define ATMEL_US_MR 0x04 /* Mode Register */
>>> #define ATMEL_US_USMODE GENMASK(3, 0) /* Mode of the USART */
>>> @@ -124,6 +129,37 @@
>>> #define ATMEL_US_NER 0x44 /* Number of Errors Register */
>>> #define ATMEL_US_IF 0x4c /* IrDA Filter Register */
>>>
>>> +#define ATMEL_US_CMPR 0x90 /* Comparaison Register */
>>> +#define ATMEL_US_FMR 0xa0 /* FIFO Mode Register */
>>> +#define ATMEL_US_TXRDYM(data) (((data) & 0x3) << 0) /* TX Ready Mode */
>>> +#define ATMEL_US_RXRDYM(data) (((data) & 0x3) << 4) /* RX Ready Mode */
>>> +#define ATMEL_US_ONE_DATA 0x0
>>> +#define ATMEL_US_TWO_DATA 0x1
>>> +#define ATMEL_US_FOUR_DATA 0x2
>>> +#define ATMEL_US_FRTSC BIT(7) /* FIFO RTS pin Control */
>>> +#define ATMEL_US_TXFTHRES(thr) (((thr) & 0x3f) << 8) /* TX FIFO Threshold */
>>> +#define ATMEL_US_RXFTHRES(thr) (((thr) & 0x3f) << 16) /* RX FIFO Threshold */
>>> +#define ATMEL_US_RXFTHRES2(thr) (((thr) & 0x3f) << 24) /* RX FIFO Threshold2 */
>>> +
>>> +#define ATMEL_US_FLR 0xa4 /* FIFO Level Register */
>>> +#define ATMEL_US_TXFL(reg) (((reg) >> 0) & 0x3f) /* TX FIFO Level */
>>> +#define ATMEL_US_RXFL(reg) (((reg) >> 16) & 0x3f) /* RX FIFO Level */
>>> +
>>> +#define ATMEL_US_FIER 0xa8 /* FIFO Interrupt Enable Register */
>>> +#define ATMEL_US_FIDR 0xac /* FIFO Interrupt Disable Register */
>>> +#define ATMEL_US_FIMR 0xb0 /* FIFO Interrupt Mask Register */
>>> +#define ATMEL_US_FESR 0xb4 /* FIFO Event Status Register */
>>> +#define ATMEL_US_TXFEF BIT(0) /* Transmit FIFO Empty Flag */
>>> +#define ATMEL_US_TXFFF BIT(1) /* Transmit FIFO Full Flag */
>>> +#define ATMEL_US_TXFTHF BIT(2) /* Transmit FIFO Threshold Flag */
>>> +#define ATMEL_US_RXFEF BIT(3) /* Receive FIFO Empty Flag */
>>> +#define ATMEL_US_RXFFF BIT(4) /* Receive FIFO Full Flag */
>>> +#define ATMEL_US_RXFTHF BIT(5) /* Receive FIFO Threshold Flag */
>>> +#define ATMEL_US_TXFPTEF BIT(6) /* Transmit FIFO Pointer Error Flag */
>>> +#define ATMEL_US_RXFPTEF BIT(7) /* Receive FIFO Pointer Error Flag */
>>> +#define ATMEL_US_TXFLOCK BIT(8) /* Transmit FIFO Lock (FESR only) */
>>> +#define ATMEL_US_RXFTHF2 BIT(9) /* Receive FIFO Threshold Flag 2 */
>>> +
>>> #define ATMEL_US_NAME 0xf0 /* Ip Name */
>>> #define ATMEL_US_VERSION 0xfc /* Ip Version */
>>>
>>> --
>>> 1.8.2.2
>>>
--
mvh
Hans-Christian Egtvedt
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
