Hi Peter,
On Mon, May 04, 2015 at 10:01:37AM -0400, Peter Hurley wrote:
> > with 4.1-rc1, my boxes with early console enabled show something like
> > this (the example is vexpress, but it for example also happens on an
> > AM335x board):
> >
> > earlycon: no match for ttyAMA0,38400n8
>
> This shouldn't impact any previous earlycon setup. Are you saying
> you're seeing a regression?
Well, it is a warning, and the system was warning-free on mainline with
the last kernels. People assume something is wrong if they read such a
message, so I'm searching for a way to do it right and get rid of the
warning again.
> How do you have early console enabled, via the command line or via DT?
Neither nor: the same SD card image runs on qemu (vexpress) and on an
AM335x. It has its primary console on the serial console:
- console=ttyAMA0,38400 (amba-pl011.c, vexpress)
- console=ttyO2,115200n8 (omap-serial.c, AM335x)
There is no "earlycon" on the commandline and nothing earlycon related I
did on purpose in the oftree.
My expectation would be to configure the system in a way that I have
everything necessary for earlecon usage compiled into the kernel, so I
can enable it manually from the bootloader whenever I need it (i.e. by
adding 'earlycon' to the kernel commandline, or by modifying the oftree
before it is handled over to the kernel).
> > The box was booted with "console=ttyAMA0,38400n8" on the commandline.
> > If I understand this right, the code in drivers/tty/serial/earlycon.c
> > calls setup_earlycon() with the string above ("ttyAMA0,38400n8") and
> > fails to find that string in the "names" part of the __earlycon_table,
> > because for the pl011 component on vexpress, the early console was
> > registered in drivers/tty/serial/amba-pl011.c with:
> >
> > OF_EARLYCON_DECLARE(pl011, "arm,pl011", pl011_early_console_setup);
> > ^^^^^ name
> >
> > So isn't that trying to match "ttyAMA0" against "arm,pl011"? I have the
> > feeling that I didn't understand the logic behind that.
> >
> > Can you elaborate about how this is supposed to work correctly?
>
> Yeah, I've been meaning to write about this but simply haven't had the
> time yet; apologies for that.
>
> The facility is hopefully best explained by the existing 8250 exemplar.
> Normally, an 8250 early console is started via command line with a
> command line parameter like:
>
> earlycon=uart,io,0x2f8,115200n8
What happens if you don't have this parameter on the kernel commandline,
but use the same port for your serial console? i.e. 'console=ttyS0'?
I would expect the same warning I see on my boxes.
> Since 2007, an 8250 early console can also be started via command line
> using console= instead, like:
>
> console=uart,io,0x2f8,115200n8
No: "console=..." puts the console on that port, not the early console.
The semantic for console= was always to specify the name of the device
there, so "console=ttyS0...", not "console=uart...", right?
> In this alternate form, this early console will go on to become the
> corresponding ttyS console.
>
> However, that functionality was exclusive to 8250 console/earlycon.
> To get this same behavior for the amba-pl011 console would look
> something like:
>
> /* drivers/tty/serial/amba-pl011.c */
>
> /* returns 0 if the console matches; otherwise, non-zero to use default matching */
> static int pl011_console_match(struct console *co, char *name, int idx, char *options)
> {
> unsigned char iotype;
> unsigned long addr;
>
> if (strncmp(name, "pl" 2) != 0 || idx != 11)
> return -ENODEV;
>
> if (uart_parse_earlycon(options, &iotype, &addr, &options))
> return -ENODEV;
>
> /* find the port from the addr */
> for (i = 0; i < ARRAY_SIZE(amba_ports); i++) {
> if (amba_ports[i] == NULL)
> continue;
> if (port->mapbase != addr)
> continue;
>
> co->index = i;
> return pl011_console_setup(co, options);
> }
>
> return -ENODEV;
> }
>
> ...
>
> static struct console amba_console = {
> ...
> .match = pl011_console_match,
> ...
> };
pl011 already has:
----------8<----------8<----------8<----------8<----------8<----------8<----------
static void pl011_early_write(struct console *con, const char *s, unsigned n)
{
struct earlycon_device *dev = con->data;
uart_console_write(&dev->port, s, n, pl011_putc);
}
static int __init pl011_early_console_setup(struct earlycon_device *device,
const char *opt)
{
if (!device->port.membase)
return -ENODEV;
device->con->write = pl011_early_write;
return 0;
}
EARLYCON_DECLARE(pl011, pl011_early_console_setup);
OF_EARLYCON_DECLARE(pl011, "arm,pl011", pl011_early_console_setup);
----------8<----------8<----------8<----------8<----------8<----------8<----------
So on oftree based systems it registers an __earlycon_table with name=pl011 and
compatible=arm,pl011. In order to see something, I need to add
console=ttyAMA0
In that case, it doesn't matter if I add an earlycon= parameter on the
commandline or not. The system takes the console= entry and hands it over to
setup_earlycon(), which tries to match it against the __earlycon_table, where
it doesn't find anything. Simply because it is pl011 there.
So switching earlycon on is broken.
If I leave out earlycon, I'd expect to switch off earlycon, which doesn't work,
because exactly the same as above happens.
So switching earlycon off is also broken.
This is either buggy or I didn't understand how it is supposed to be used.
rsc
--
Pengutronix e.K. | |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
