This patch replaces a switch-case by a formula using rational best
approximation that does necessary calculations for intel_mid_set_termios().
Below is a list of the calculations done for all defined baud rates. Each line
in a format: 1) nominator, 2) denominator, 3) prescaler, 4) Fuart, 5) port UART
clock, 6) list of baud rates with DLAB values.
24 25 12 48000000 64000000 4000000(1)
49 50 14 49000000 56000000 3500000(1)
4 5 16 40000000 40000000 2500000(1)
16 25 16 32000000 32000000 500000(4),1000000(2),2000000(1)
24 25 16 48000000 48000000 1500000(2),3000000(1)
2304 3125 16 36864000 36864000 576000(4),1152000(2)
8192 15625 16 26214400 26214400 50(32768),200(8192)
9216 15625 16 29491200 29491200 1800(1024),57600(32),115200(16),
230400(8),460800(4),921600(2),1843200(1)
12288 15625 16 39321600 39321600 75(32768),150(16384),300(8192),
600(4096),1200(2048),2400(1024),4800(512),
9600(256),19200(128),38400(64)
45056 78125 16 28835840 28835840 110(16384)
274432 390625 16 35127296 35127296 134(16384)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
---
drivers/tty/serial/8250/8250_pci.c | 78 +++++++++++++++++---------------------
1 file changed, 34 insertions(+), 44 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 9bb2eec..0bb3d0b 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1502,60 +1502,50 @@ byt_serial_setup(struct serial_private *priv,
#define INTEL_MID_UART_PS 0x30
#define INTEL_MID_UART_MUL 0x34
+#define INTEL_MID_UART_DIV 0x38
-static void intel_mid_set_termios_50M(struct uart_port *p,
- struct ktermios *termios,
- struct ktermios *old)
+static void intel_mid_set_termios(struct uart_port *p,
+ struct ktermios *termios,
+ struct ktermios *old,
+ unsigned long fref)
{
unsigned int baud = tty_termios_baud_rate(termios);
- u32 ps, mul;
-
- /*
- * The uart clk is 50Mhz, and the baud rate come from:
- * baud = 50M * MUL / (DIV * PS * DLAB)
- *
- * For those basic low baud rate we can get the direct
- * scalar from 2746800, like 115200 = 2746800/24. For those
- * higher baud rate, we handle them case by case, mainly by
- * adjusting the MUL/PS registers, and DIV register is kept
- * as default value 0x3d09 to make things simple.
- */
-
- ps = 0x10;
-
- switch (baud) {
- case 500000:
- case 1000000:
- case 1500000:
- case 3000000:
- mul = 0x3a98;
- p->uartclk = 48000000;
- break;
- case 2000000:
- case 4000000:
- mul = 0x2710;
- ps = 0x08;
- p->uartclk = 64000000;
- break;
- case 2500000:
- mul = 0x30d4;
- p->uartclk = 40000000;
- break;
- case 3500000:
- mul = 0x3345;
- ps = 0x0c;
- p->uartclk = 56000000;
- break;
- default:
- mul = 0x2400;
- p->uartclk = 29491200;
+ unsigned short ps = 16;
+ unsigned long fuart = baud * ps;
+ unsigned long w = BIT(24) - 1;
+ unsigned long mul, div;
+
+ if (fref < fuart) {
+ /* Find prescaler value that satisfies Fuart < Fref */
+ if (fref > baud)
+ ps = fref / baud; /* baud rate too high */
+ else
+ ps = 1; /* PLL case */
+ fuart = baud * ps;
+ } else {
+ /* Get Fuart closer to Fref */
+ fuart *= rounddown_pow_of_two(fref / fuart);
}
+ p->uartclk = fuart * 16 / ps; /* core uses ps = 16 always */
+ rational_best_approximation(fuart, fref, w, w, &mul, &div);
+
writel(ps, p->membase + INTEL_MID_UART_PS); /* set PS */
writel(mul, p->membase + INTEL_MID_UART_MUL); /* set MUL */
+ writel(div, p->membase + INTEL_MID_UART_DIV);
serial8250_do_set_termios(p, termios, old);
}
+static void intel_mid_set_termios_50M(struct uart_port *p,
+ struct ktermios *termios,
+ struct ktermios *old)
+{
+ /*
+ * The uart clk is 50Mhz, and the baud rate come from:
+ * baud = 50M * MUL / (DIV * PS * DLAB)
+ */
+ intel_mid_set_termios(p, termios, old, 50000000);
+}
static bool intel_mid_dma_filter(struct dma_chan *chan, void *param)
{
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
