16z135 IP Core has changed so the driver needs to be updated to respect
these changes. The following changes have been made:
* Don't invert the 16z135 modem status register when reading.
* Add module parameter to configure the (baud rate dependent) RX timeout.
Character timeout in seconds = (timeout_reg * baud_reg * 4)/freq_reg.
* Enable the handling of UART core's automatic flow control feature.
When AFE is active disable generation of modem status IRQs.
* Rework the handling of IRQs to be conform with newer FPGA versions and
take precautions not to miss an interrupt because of the destructive read
of the IIR register.
* Correct men_z135_handle_modem_status(), MSR is stat_reg[15:8] not
stat_reg[7:0]
* Correct calling of uart_handle_{dcd,cts}_change()
* Correct handling of hardware's automode
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@xxxxxx>
---
Changes to v1:
Incorporated comments of Jiri Slaby:
* Timeout value is documented in module parameter description
* rx_timeout variable is uint
* Changed IRQ handled variable to bool
* Changed if statement for RDA or CTI IRQ
Changes to v2:
Correct men_z135_handle_modem_status(), MSR is stat_reg[15:8] not stat_reg[7:0]
Changes to v3:
Correct calling of uart_handle_{dcd,cts}_change()
Correct handling of hardware's automode
drivers/tty/serial/men_z135_uart.c | 154 ++++++++++++++++++++++++++-----------
1 file changed, 108 insertions(+), 46 deletions(-)
diff --git a/drivers/tty/serial/men_z135_uart.c b/drivers/tty/serial/men_z135_uart.c
index 30e9e60..90104c4 100644
--- a/drivers/tty/serial/men_z135_uart.c
+++ b/drivers/tty/serial/men_z135_uart.c
@@ -23,7 +23,6 @@
#define MEN_Z135_MAX_PORTS 12
#define MEN_Z135_BASECLK 29491200
#define MEN_Z135_FIFO_SIZE 1024
-#define MEN_Z135_NUM_MSI_VECTORS 2
#define MEN_Z135_FIFO_WATERMARK 1020
#define MEN_Z135_STAT_REG 0x0
@@ -34,12 +33,11 @@
#define MEN_Z135_CONF_REG 0x808
#define MEN_Z135_UART_FREQ 0x80c
#define MEN_Z135_BAUD_REG 0x810
-#define MENZ135_TIMEOUT 0x814
+#define MEN_Z135_TIMEOUT 0x814
#define MEN_Z135_MEM_SIZE 0x818
-#define IS_IRQ(x) ((x) & 1)
-#define IRQ_ID(x) (((x) >> 1) & 7)
+#define IRQ_ID(x) ((x) & 0x1f)
#define MEN_Z135_IER_RXCIEN BIT(0) /* RX Space IRQ */
#define MEN_Z135_IER_TXCIEN BIT(1) /* TX Space IRQ */
@@ -94,11 +92,11 @@
#define MEN_Z135_LSR_TEXP BIT(6)
#define MEN_Z135_LSR_RXFIFOERR BIT(7)
-#define MEN_Z135_IRQ_ID_MST 0
-#define MEN_Z135_IRQ_ID_TSA 1
-#define MEN_Z135_IRQ_ID_RDA 2
-#define MEN_Z135_IRQ_ID_RLS 3
-#define MEN_Z135_IRQ_ID_CTI 6
+#define MEN_Z135_IRQ_ID_RLS BIT(0)
+#define MEN_Z135_IRQ_ID_RDA BIT(1)
+#define MEN_Z135_IRQ_ID_CTI BIT(2)
+#define MEN_Z135_IRQ_ID_TSA BIT(3)
+#define MEN_Z135_IRQ_ID_MST BIT(4)
#define LCR(x) (((x) >> MEN_Z135_LCR_SHIFT) & 0xff)
@@ -118,12 +116,18 @@ static int align;
module_param(align, int, S_IRUGO);
MODULE_PARM_DESC(align, "Keep hardware FIFO write pointer aligned, default 0");
+static uint rx_timeout;
+module_param(rx_timeout, uint, S_IRUGO);
+MODULE_PARM_DESC(rx_timeout, "RX timeout. "
+ "Timeout in seconds = (timeout_reg * baud_reg * 4) / freq_reg");
+
struct men_z135_port {
struct uart_port port;
struct mcb_device *mdev;
unsigned char *rxbuf;
u32 stat_reg;
spinlock_t lock;
+ bool automode;
};
#define to_men_z135(port) container_of((port), struct men_z135_port, port)
@@ -180,12 +184,16 @@ static inline void men_z135_reg_clr(struct men_z135_port *uart,
*/
static void men_z135_handle_modem_status(struct men_z135_port *uart)
{
- if (uart->stat_reg & MEN_Z135_MSR_DDCD)
+ u8 msr;
+
+ msr = (uart->stat_reg >> 8) & 0xff;
+
+ if (msr & MEN_Z135_MSR_DDCD)
uart_handle_dcd_change(&uart->port,
- uart->stat_reg & ~MEN_Z135_MSR_DCD);
- if (uart->stat_reg & MEN_Z135_MSR_DCTS)
+ msr & MEN_Z135_MSR_DCD);
+ if (msr & MEN_Z135_MSR_DCTS)
uart_handle_cts_change(&uart->port,
- uart->stat_reg & ~MEN_Z135_MSR_CTS);
+ msr & MEN_Z135_MSR_CTS);
}
static void men_z135_handle_lsr(struct men_z135_port *uart)
@@ -322,7 +330,8 @@ static void men_z135_handle_tx(struct men_z135_port *uart)
txfree = MEN_Z135_FIFO_WATERMARK - txc;
if (txfree <= 0) {
- pr_err("Not enough room in TX FIFO have %d, need %d\n",
+ dev_err(&uart->mdev->dev,
+ "Not enough room in TX FIFO have %d, need %d\n",
txfree, qlen);
goto irq_en;
}
@@ -373,43 +382,54 @@ out:
* @irq: The IRQ number
* @data: Pointer to UART port
*
- * Check IIR register to see which tasklet to start.
+ * Check IIR register to find the cause of the interrupt and handle it.
+ * It is possible that multiple interrupts reason bits are set and reading
+ * the IIR is a destructive read, so we always need to check for all possible
+ * interrupts and handle them.
*/
static irqreturn_t men_z135_intr(int irq, void *data)
{
struct men_z135_port *uart = (struct men_z135_port *)data;
struct uart_port *port = &uart->port;
+ bool handled = false;
+ unsigned long flags;
int irq_id;
uart->stat_reg = ioread32(port->membase + MEN_Z135_STAT_REG);
- /* IRQ pending is low active */
- if (IS_IRQ(uart->stat_reg))
- return IRQ_NONE;
-
irq_id = IRQ_ID(uart->stat_reg);
- switch (irq_id) {
- case MEN_Z135_IRQ_ID_MST:
- men_z135_handle_modem_status(uart);
- break;
- case MEN_Z135_IRQ_ID_TSA:
- men_z135_handle_tx(uart);
- break;
- case MEN_Z135_IRQ_ID_CTI:
- dev_dbg(&uart->mdev->dev, "Character Timeout Indication\n");
- /* Fallthrough */
- case MEN_Z135_IRQ_ID_RDA:
- /* Reading data clears RX IRQ */
- men_z135_handle_rx(uart);
- break;
- case MEN_Z135_IRQ_ID_RLS:
+
+ if (!irq_id)
+ goto out;
+
+ spin_lock_irqsave(&port->lock, flags);
+ /* It's save to write to IIR[7:6] RXC[9:8] */
+ iowrite8(irq_id, port->membase + MEN_Z135_STAT_REG);
+
+ if (irq_id & MEN_Z135_IRQ_ID_RLS) {
men_z135_handle_lsr(uart);
- break;
- default:
- dev_warn(&uart->mdev->dev, "Unknown IRQ id %d\n", irq_id);
- return IRQ_NONE;
+ handled = true;
+ }
+
+ if (irq_id & (MEN_Z135_IRQ_ID_RDA | MEN_Z135_IRQ_ID_CTI)) {
+ if (irq_id & MEN_Z135_IRQ_ID_CTI)
+ dev_dbg(&uart->mdev->dev, "Character Timeout Indication\n");
+ men_z135_handle_rx(uart);
+ handled = true;
+ }
+
+ if (irq_id & MEN_Z135_IRQ_ID_TSA) {
+ men_z135_handle_tx(uart);
+ handled = true;
}
- return IRQ_HANDLED;
+ if (irq_id & MEN_Z135_IRQ_ID_MST) {
+ men_z135_handle_modem_status(uart);
+ handled = true;
+ }
+
+ spin_unlock_irqrestore(&port->lock, flags);
+out:
+ return IRQ_RETVAL(handled);
}
/**
@@ -464,21 +484,37 @@ static unsigned int men_z135_tx_empty(struct uart_port *port)
*/
static void men_z135_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
- struct men_z135_port *uart = to_men_z135(port);
- u32 conf_reg = 0;
+ u32 old;
+ u32 conf_reg;
+ conf_reg = old = ioread32(port->membase + MEN_Z135_CONF_REG);
if (mctrl & TIOCM_RTS)
conf_reg |= MEN_Z135_MCR_RTS;
+ else
+ conf_reg &= ~MEN_Z135_MCR_RTS;
+
if (mctrl & TIOCM_DTR)
conf_reg |= MEN_Z135_MCR_DTR;
+ else
+ conf_reg &= ~MEN_Z135_MCR_DTR;
+
if (mctrl & TIOCM_OUT1)
conf_reg |= MEN_Z135_MCR_OUT1;
+ else
+ conf_reg &= ~MEN_Z135_MCR_OUT1;
+
if (mctrl & TIOCM_OUT2)
conf_reg |= MEN_Z135_MCR_OUT2;
+ else
+ conf_reg &= ~MEN_Z135_MCR_OUT2;
+
if (mctrl & TIOCM_LOOP)
conf_reg |= MEN_Z135_MCR_LOOP;
+ else
+ conf_reg &= ~MEN_Z135_MCR_LOOP;
- men_z135_reg_set(uart, MEN_Z135_CONF_REG, conf_reg);
+ if (conf_reg != old)
+ iowrite32(conf_reg, port->membase + MEN_Z135_CONF_REG);
}
/**
@@ -490,12 +526,9 @@ static void men_z135_set_mctrl(struct uart_port *port, unsigned int mctrl)
static unsigned int men_z135_get_mctrl(struct uart_port *port)
{
unsigned int mctrl = 0;
- u32 stat_reg;
u8 msr;
- stat_reg = ioread32(port->membase + MEN_Z135_STAT_REG);
-
- msr = ~((stat_reg >> 8) & 0xff);
+ msr = ioread8(port->membase + MEN_Z135_STAT_REG + 1);
if (msr & MEN_Z135_MSR_CTS)
mctrl |= TIOCM_CTS;
@@ -524,6 +557,19 @@ static void men_z135_stop_tx(struct uart_port *port)
men_z135_reg_clr(uart, MEN_Z135_CONF_REG, MEN_Z135_IER_TXCIEN);
}
+/*
+ * men_z135_disable_ms() - Disable Modem Status
+ * port: The UART port
+ *
+ * Enable Modem Status IRQ.
+ */
+static void men_z135_disable_ms(struct uart_port *port)
+{
+ struct men_z135_port *uart = to_men_z135(port);
+
+ men_z135_reg_clr(uart, MEN_Z135_CONF_REG, MEN_Z135_IER_MSIEN);
+}
+
/**
* men_z135_start_tx() - Start transmitting characters
* @port: The UART port
@@ -535,6 +581,9 @@ static void men_z135_start_tx(struct uart_port *port)
{
struct men_z135_port *uart = to_men_z135(port);
+ if (uart->automode)
+ men_z135_disable_ms(port);
+
men_z135_handle_tx(uart);
}
@@ -584,6 +633,9 @@ static int men_z135_startup(struct uart_port *port)
iowrite32(conf_reg, port->membase + MEN_Z135_CONF_REG);
+ if (rx_timeout)
+ iowrite32(rx_timeout, port->membase + MEN_Z135_TIMEOUT);
+
return 0;
}
@@ -603,6 +655,7 @@ static void men_z135_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
+ struct men_z135_port *uart = to_men_z135(port);
unsigned int baud;
u32 conf_reg;
u32 bd_reg;
@@ -643,6 +696,15 @@ static void men_z135_set_termios(struct uart_port *port,
} else
lcr |= MEN_Z135_PAR_DIS << MEN_Z135_PEN_SHIFT;
+ conf_reg |= MEN_Z135_IER_MSIEN;
+ if (termios->c_cflag & CRTSCTS) {
+ conf_reg |= MEN_Z135_MCR_RCFC;
+ uart->automode = true;
+ } else {
+ conf_reg &= ~MEN_Z135_MCR_RCFC;
+ uart->automode = false;
+ }
+
termios->c_cflag &= ~CMSPAR; /* Mark/Space parity is not supported */
conf_reg |= lcr << MEN_Z135_LCR_SHIFT;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
