* Sebastian Andrzej Siewior <bigeasy@xxxxxxxxxxxxx> [140716 07:47]: > This patch provides a 8250-core based UART driver for the internal OMAP > UART. The longterm goal is to provide the same functionality as the > current OMAP uart driver and hopefully DMA support which could borrowed > from the 8250-core. > > It has been only tested as console UART on am335x-evm and dra7-evm. > The device name is ttyS based instead of ttyO. If a ttyO based node name > is required please ask udev for it. If both driver are activated (this > and omap-serial) then this serial driver will take control over the > device due to the link order > > v3…v4: > - drop RS485 support > - wire up ->throttle / ->unthrottle > v2…v3: > - wire up startup & shutdown for wakeup-irq handling. > - RS485 handling (well the core does). > > v1…v2: > - added runtime PM. Could somebody could plese double check > this? > - added omap_8250_set_termios() Seems to boot a bit further now with output from serial console initially, then I'm getting the following error again that's probably related to clocks not enabled when the registers are accessed: [ 1.050231] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.068664] 4806a000.serial: ttyS0 at MMIO 0x4806a000 (irq = 88, base_baud = 3000000) is a OMAP [ 1.074676] 4806c000.serial: ttyS1 at MMIO 0x4806c000 (irq = 89, base_baud = 3000000) is a OMAP [ 1.078613] console [ttyS2] disabled [ 1.079193] 49020000.serial: ttyS2 at MMIO 0x49020000 (irq = 90, base_baud = 3000000) is a OMAP [ 1.938110] console [ttyS2] enabled [ 1.946533] 49042000.serial: ttyS3 at MMIO 0x49042000 (irq = 96, base_baud = 3000000) is a OMAP ... [ 5.538421] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfb020000 [ 5.546142] Internal error: : 1028 [#1] SMP ARM [ 5.550720] Modules linked in: [ 5.553802] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.16.0-rc5-00070-g1f95851 #129 [ 5.561584] task: ce058b00 ti: ce05a000 task.ti: ce05a000 [ 5.567016] PC is at mem32_serial_in+0xc/0x1c [ 5.571411] LR is at serial8250_do_startup+0xc8/0x89c [ 5.576507] pc : [<c034731c>] lr : [<c034a988>] psr: 60000113 [ 5.576507] sp : ce05bcf0 ip : c0a008e8 fp : ce46c400 [ 5.588043] r10: 00000000 r9 : cda7a680 r8 : ce46c68c [ 5.593292] r7 : ce46c400 r6 : 00000000 r5 : ce548e10 r4 : c10abf34 [ 5.599853] r3 : fb020000 r2 : 00000002 r1 : fb020000 r0 : c10abf34 [ 5.606414] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel [ 5.613769] Control: 10c5387d Table: 80004019 DAC: 00000015 [ 5.619537] Process swapper/0 (pid: 1, stack limit = 0xce05a248) ... [ 5.835601] [<c034731c>] (mem32_serial_in) from [<c034a988>] (serial8250_do_startup+0xc8/0x89c) [ 5.844360] [<c034a988>] (serial8250_do_startup) from [<c034c58c>] (omap_8250_startup+0x5c/0xdc) [ 5.853179] [<c034c58c>] (omap_8250_startup) from [<c034b170>] (serial8250_startup+0x14/0x20) [ 5.861755] [<c034b170>] (serial8250_startup) from [<c0346584>] (uart_startup.part.3+0x7c/0x1dc) [ 5.870605] [<c0346584>] (uart_startup.part.3) from [<c03470f4>] (uart_open+0xe4/0x124) [ 5.878662] [<c03470f4>] (uart_open) from [<c032c528>] (tty_open+0x130/0x58c) [ 5.885864] [<c032c528>] (tty_open) from [<c01216ec>] (chrdev_open+0x9c/0x174) [ 5.893127] [<c01216ec>] (chrdev_open) from [<c011b8cc>] (do_dentry_open+0x1d0/0x310) [ 5.901000] [<c011b8cc>] (do_dentry_open) from [<c011bd90>] (finish_open+0x34/0x4c) [ 5.908721] [<c011bd90>] (finish_open) from [<c012a8f0>] (do_last.isra.27+0x5a4/0xb98) [ 5.916687] [<c012a8f0>] (do_last.isra.27) from [<c012af98>] (path_openat+0xb4/0x5e4) [ 5.924560] [<c012af98>] (path_openat) from [<c012b7d4>] (do_filp_open+0x2c/0x80) [ 5.932098] [<c012b7d4>] (do_filp_open) from [<c011cd0c>] (do_sys_open+0x100/0x1d0) [ 5.939788] [<c011cd0c>] (do_sys_open) from [<c07b6ce0>] (kernel_init_freeable+0x124/0x1c8) [ 5.948211] [<c07b6ce0>] (kernel_init_freeable) from [<c054ed28>] (kernel_init+0x8/0xe4) [ 5.956359] [<c054ed28>] (kernel_init) from [<c000e868>] (ret_from_fork+0x14/0x2c) ... [ 5.974792] In-band Error seen by MPU at address 0 [ 5.979675] ------------[ cut here ]------------ [ 5.984344] WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_smx.c:162 omap3_l3_app_irq+0xcc/0x124() ... Regards, Tony -- To unsubscribe from this list: send the line "unsubscribe linux-serial" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
