Thu, 3 Apr 2014 00:49:14 -0400 от jon@xxxxxxxxxx:
> From: Jon Ringle <jringle@xxxxxxxxxxxxx>
>
> The SC16IS7xx is a slave I2C-bus/SPI interface to a single-channel
> high performance UART. The SC16IS7xx’s internal register set is
> backward-compatible with the widely used and widely popular 16C450.
>
> The SC16IS7xx also provides additional advanced features such as
> auto hardware and software flow control, automatic RS-485 support, and
> software reset.
>
> Signed-off-by: Jon Ringle <jringle@xxxxxxxxxxxxx>
> ---
...
> + tristate "SC16IS7xx serial support"
> + select SERIAL_CORE
> + select REGMAP_I2C if I2C
> + default n
"n" is already default choice. There is no need to specify this.
...
> +#include <linux/serial.h>
> +#include <linux/spi/spi.h>
What a reason to include SPI header?
...
> + * The programmer must program the TCR such that TCR[3:0] > TCR[7:4]. There is
> + * no built-in hardware check to make sure this condition is met. Also, the TCR
> + * must be programmed with this condition before auto RTS or software flow
> + * control is enabled to avoid spurious operation of the device.
> + */
> +#define SC16IS7XX_TCR_RX_HALT(words) (((words / 4) & 0x0f) << 0)
> +#define SC16IS7XX_TCR_RX_RESUME(words) (((words / 4) & 0x0f) << 4)
"words" on the right side should be framed by brackets.
...
> + * When TLR is used for RX trigger level control, FCR[7:6] should be left at the
> + * default state, that is, ‘00’.
> + */
> +#define SC16IS7XX_TLR_TX_TRIGGER(words) (((words / 4) & 0x0f) << 0)
> +#define SC16IS7XX_TLR_RX_TRIGGER(words) (((words / 4) & 0x0f) << 4)
Ditto.
...
> +static void sc16is7xx_config_rs485(struct uart_port *port,
> + struct serial_rs485 *rs485)
> +{
> + struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
> +
> + one->rs485 = *rs485;
> +
> + if (one->rs485.flags & SER_RS485_ENABLED) {
> + sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG,
> + SC16IS7XX_EFCR_AUTO_RS485_BIT,
> + SC16IS7XX_EFCR_AUTO_RS485_BIT);
> + } else {
> + sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG,
> + SC16IS7XX_EFCR_AUTO_RS485_BIT,
> + 0);
> + }
> +}
This function will get "unused" warning if TIOCSRS485 and
TIOCGRS485 is not defined.
...
> +static int sc16is7xx_startup(struct uart_port *port)
> +{
...
> + sc16is7xx_port_update(port, SC16IS7XX_EFCR_REG,
> + SC16IS7XX_EFCR_AUTO_RS485_BIT,
> + SC16IS7XX_EFCR_AUTO_RS485_BIT);
You should do not set optional RS485 mode unconditionally.
Since IOCTL for RS485 is used, this should be enough.
---
��.n��������+%������w��{.n�����{��ǫ����{ay� ʇڙ���f���h������_�(�階�ݢj"��������G����?���&��
