Re: [PATCH resend] serial_core: Fix pm imbalance on unbind

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 03/21/2014 05:08 AM, Geert Uytterhoeven wrote:
From: Geert Uytterhoeven <geert+renesas@xxxxxxxxxxxxxx>

When a serial port is closed, uart_close() takes care of shutting down the
hardware, and powering it down.

When a serial port is unbound while in use, uart_close() bypasses all of
this, as this is supposed to be done through uart_hangup() (invoked via
tty_vhangup() in uart_remove_one_port()).

However, uart_hangup() does not set the hardware's power state, leaving it
powered up.  This may also lead to unbounded nesting counts in clock and
power management, depending on their internal implementation.

Make sure to power down the port in uart_hangup(), except when the port is
used as a serial console. For serial consoles, this must be postponed until
after their deregistration in uart_remove_one_port() (symmetry with
registration in uart_configure_port(), invoked from uart_add_one_port()).

After this, the module clock used by the sh-sci driver is disabled on
unbind while the serial port is in use.

Signed-off-by: Geert Uytterhoeven <geert+renesas@xxxxxxxxxxxxxx>
---
  drivers/tty/serial/serial_core.c |    8 ++++++--
  1 file changed, 6 insertions(+), 2 deletions(-)

diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c
index 2cf5649a6dc0..56dda84f82a5 100644
--- a/drivers/tty/serial/serial_core.c
+++ b/drivers/tty/serial/serial_core.c
@@ -1452,6 +1452,8 @@ static void uart_hangup(struct tty_struct *tty)
  		clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags);
  		spin_unlock_irqrestore(&port->lock, flags);
  		tty_port_tty_set(port, NULL);
+		if (!uart_console(state->uart_port))
+			uart_change_pm(state, UART_PM_STATE_OFF);

Ok.

  		wake_up_interruptible(&port->open_wait);
  		wake_up_interruptible(&port->delta_msr_wait);
  	}
@@ -2681,10 +2683,12 @@ int uart_remove_one_port(struct uart_driver *drv, struct uart_port *uport)
  	}

  	/*
-	 * If the port is used as a console, unregister it
+	 * If the port is used as a console, unregister it, and power it down
  	 */
-	if (uart_console(uport))
+	if (uart_console(uport)) {
  		unregister_console(uport->cons);
+		uart_change_pm(state, UART_PM_STATE_OFF);

Won't this power off the port while tty consoles may still be open?
I think the right thing here is to unregister_console then set uport->cons = NULL

[uport->cons is properly reassigned when/if a port is re-added via
uart_add_one_port()).]

Then, uart_close() will power off the port when all ttys using the port have
been closed.

+	}

  	/*
  	 * Free the port IO and memory resources, if any.


--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux