On 10/17/2013 05:08 PM, Soren Brinkmann wrote:
From: Vlad Lungu <vlad.lungu@xxxxxxxxxxxxx>
The Cadence UART does not do break detection, even if the
datasheet says it does. This patch adds break detection in
software (tested in 8N1 mode only) and enables SYSRQ,
allowing for Break-g to enter KDB and all the other goodies.
Signed-off-by: Vlad Lungu <vlad.lungu@xxxxxxxxxxxxx>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xxxxxxxxxx>
---
I ported this patch to 3.12 and fixed some style issues
---
drivers/tty/serial/xilinx_uartps.c | 50 +++++++++++++++++++++++++++++++++++++-
1 file changed, 49 insertions(+), 1 deletion(-)
diff --git a/drivers/tty/serial/xilinx_uartps.c b/drivers/tty/serial/xilinx_uartps.c
index 8c0745951605..5d5557af4d22 100644
--- a/drivers/tty/serial/xilinx_uartps.c
+++ b/drivers/tty/serial/xilinx_uartps.c
@@ -11,13 +11,17 @@
*
*/
+#if defined(CONFIG_SERIAL_XILINX_PS_UART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
#include <linux/platform_device.h>
#include <linux/serial.h>
+#include <linux/console.h>
#include <linux/serial_core.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
-#include <linux/console.h>
#include <linux/clk.h>
#include <linux/irq.h>
#include <linux/io.h>
@@ -128,6 +132,9 @@
#define XUARTPS_IXR_RXEMPTY 0x00000002 /* RX FIFO empty interrupt. */
#define XUARTPS_IXR_MASK 0x00001FFF /* Valid bit mask */
+/* Goes in read_status_mask for break detection as the HW doesn't do it*/
+#define XUARTPS_IXR_BRK 0x80000000
+
/** Channel Status Register
*
* The channel status register (CSR) is provided to enable the control logic
@@ -171,6 +178,23 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
*/
isrstatus = xuartps_readl(XUARTPS_ISR_OFFSET);
+ /*
+ * There is no hardware break detection, so we interpret framing
+ * error with all-zeros data as a break sequence. Most of the time,
+ * there's another non-zero byte at the end of the sequence.
+ */
+
+ if (isrstatus & XUARTPS_IXR_FRAMING) {
+ while (!(xuartps_readl(XUARTPS_SR_OFFSET) &
+ XUARTPS_SR_RXEMPTY)) {
+ if (!xuartps_readl(XUARTPS_FIFO_OFFSET)) {
+ port->read_status_mask |= XUARTPS_IXR_BRK;
+ isrstatus &= ~XUARTPS_IXR_FRAMING;
+ }
+ }
+ xuartps_writel(XUARTPS_IXR_FRAMING, XUARTPS_ISR_OFFSET);
+ }
+
/* drop byte with parity error if IGNPAR specified */
if (isrstatus & port->ignore_status_mask & XUARTPS_IXR_PARITY)
isrstatus &= ~(XUARTPS_IXR_RXTRIG | XUARTPS_IXR_TOUT);
@@ -184,6 +208,30 @@ static irqreturn_t xuartps_isr(int irq, void *dev_id)
while ((xuartps_readl(XUARTPS_SR_OFFSET) &
XUARTPS_SR_RXEMPTY) != XUARTPS_SR_RXEMPTY) {
data = xuartps_readl(XUARTPS_FIFO_OFFSET);
+
+ /* Non-NULL byte after BREAK is garbage (99%) */
+ if (data && (port->read_status_mask &
+ XUARTPS_IXR_BRK)) {
+ port->read_status_mask &= ~XUARTPS_IXR_BRK;
+ port->icount.brk++;
+ if (uart_handle_break(port))
+ continue;
+ }
+
+ /*
+ * uart_handle_sysrq_char() doesn't work if
+ * spinlocked, for some reason
+ */
^^^^^^^^^^^^^^^
Because the console write method, xuartps_console_write(), tries to
lock the port->lock. Double-claim deadlock.
+ if (port->sysrq) {
+ spin_unlock(&port->lock);
+ if (uart_handle_sysrq_char(port,
+ (unsigned char)data)) {
+ spin_lock(&port->lock);
+ continue;
+ }
+ spin_lock(&port->lock);
+ }
+
port->icount.rx++;
if (isrstatus & XUARTPS_IXR_PARITY) {
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
