The code in 8250.c for detecting ARM/XScale UARTs says:
* Try writing and reading the UART_IER_UUE bit (b6).
* If it works, this is probably one of the Xscale platform's
* internal UARTs.
If the above passes, it then goes on to:
* It's an Xscale.
* We'll leave the UART_IER_UUE bit set to 1 (enabled).
However, the CH352 uses the UART_IER_UUE as the LOWPOWER function,
so it is readable and writable. According to the datasheet:
"LOWPOWER:When the bit is 1, close the internal benchmark
clock of serial port to set into low-power status.
So it essentially gets mis-detected as Xscale, and gets
powered down in the process. The device in question where
this was seen is listed by lspci as:
Serial controller: Device 4348:3253 (rev 10) (prog-if 02 [16550])
Re-using the 353 quirk which just sets flags to fixed and type
to 16550 is suitable for fixing the 352 as well.
Signed-off-by: Wang YanQing <udknight@xxxxxxxxx>
Signed-off-by: Paul Gortmaker <paul.gortmaker@xxxxxxxxxxxxx>
---
Changes
V1-V2:
1: Use a better descriptive subject by Paul Gortmaker
2: Add more detail log by Paul Gortmaker
I resend this version, because it will make merge job easy, and I
will not owe gregkh juice :)
Thanks, Paul Gortmaker and all
drivers/tty/serial/8250/8250_pci.c | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 791c5a7..5805f89 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1554,6 +1554,7 @@ pci_wch_ch353_setup(struct serial_private *priv,
#define PCI_DEVICE_ID_PLX_CRONYX_OMEGA 0xc001
#define PCI_DEVICE_ID_INTEL_PATSBURG_KT 0x1d3d
#define PCI_VENDOR_ID_WCH 0x4348
+#define PCI_DEVICE_ID_WCH_CH352_2S 0x3253
#define PCI_DEVICE_ID_WCH_CH353_4S 0x3453
#define PCI_DEVICE_ID_WCH_CH353_2S1PF 0x5046
#define PCI_DEVICE_ID_WCH_CH353_2S1P 0x7053
@@ -2180,6 +2181,14 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
.subdevice = PCI_ANY_ID,
.setup = pci_wch_ch353_setup,
},
+ /* WCH CH352 2S card (16550 clone) */
+ {
+ .vendor = PCI_VENDOR_ID_WCH,
+ .device = PCI_DEVICE_ID_WCH_CH352_2S,
+ .subvendor = PCI_ANY_ID,
+ .subdevice = PCI_ANY_ID,
+ .setup = pci_wch_ch353_setup,
+ },
/*
* ASIX devices with FIFO bug
*/
@@ -4869,6 +4878,10 @@ static struct pci_device_id serial_pci_tbl[] = {
PCI_ANY_ID, PCI_ANY_ID,
0, 0, pbn_b0_bt_2_115200 },
+ { PCI_VENDOR_ID_WCH, PCI_DEVICE_ID_WCH_CH352_2S,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0, pbn_b0_bt_2_115200 },
+
/*
* Commtech, Inc. Fastcom adapters
*/
--
1.7.12.4.dirty
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
