I've managed to find an 8 port version of the card 4 port card which was discussed here: http://marc.info/?l=linux-serial&m=120760744205314&w=2 Looking back at that thread there were two issues in the original patch. 1) The I/O ports for the UARTs are within BAR2 not BAR0. This can been seen in the original post. 2) A serial quirk isn't needed as these cards have no memory in BAR0 which makes pci_plx9050_init just return. This patch fixes the 4 port support to use BAR2, removes the bogus quirk and adds support for the 8 port card. $ lspci -vvv -n -s 00:08.0 00:08.0 0780: 10b5:9050 (rev 01) Subsystem: 10b5:1588 Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 17 Region 1: I/O ports at ff00 [size=128] Region 2: I/O ports at fe00 [size=64] Region 3: I/O ports at fd00 [size=8] Capabilities: <access denied> Kernel driver in use: serial $ dmesg | grep 0000:00:08.0: [ 0.083320] pci 0000:00:08.0: [10b5:9050] type 0 class 0x000780 [ 0.083355] pci 0000:00:08.0: reg 14: [io 0xff00-0xff7f] [ 0.083369] pci 0000:00:08.0: reg 18: [io 0xfe00-0xfe3f] [ 0.083382] pci 0000:00:08.0: reg 1c: [io 0xfd00-0xfd07] [ 0.083460] pci 0000:00:08.0: PME# supported from D0 D3hot [ 1.212867] 0000:00:08.0: ttyS4 at I/O 0xfe00 (irq = 17) is a 16550A [ 1.233073] 0000:00:08.0: ttyS5 at I/O 0xfe08 (irq = 17) is a 16550A [ 1.253270] 0000:00:08.0: ttyS6 at I/O 0xfe10 (irq = 17) is a 16550A [ 1.273468] 0000:00:08.0: ttyS7 at I/O 0xfe18 (irq = 17) is a 16550A [ 1.293666] 0000:00:08.0: ttyS8 at I/O 0xfe20 (irq = 17) is a 16550A [ 1.313863] 0000:00:08.0: ttyS9 at I/O 0xfe28 (irq = 17) is a 16550A [ 1.334061] 0000:00:08.0: ttyS10 at I/O 0xfe30 (irq = 17) is a 16550A [ 1.354258] 0000:00:08.0: ttyS11 at I/O 0xfe38 (irq = 17) is a 16550A Signed-off-by: Scott Ashcroft <scott.ashcroft@xxxxxxxxxx> diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 791c5a7..85c6bf9 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -1571,6 +1571,7 @@ pci_wch_ch353_setup(struct serial_private *priv, /* Unknown vendors/cards - this should not be in linux/pci_ids.h */ #define PCI_SUBDEVICE_ID_UNKNOWN_0x1584 0x1584 +#define PCI_SUBDEVICE_ID_UNKNOWN_0x1588 0x1588 /* * Master list of serial port init/setup/exit quirks. @@ -1852,15 +1853,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { }, { .vendor = PCI_VENDOR_ID_PLX, - .device = PCI_DEVICE_ID_PLX_9050, - .subvendor = PCI_VENDOR_ID_PLX, - .subdevice = PCI_SUBDEVICE_ID_UNKNOWN_0x1584, - .init = pci_plx9050_init, - .setup = pci_default_setup, - .exit = pci_plx9050_exit, - }, - { - .vendor = PCI_VENDOR_ID_PLX, .device = PCI_DEVICE_ID_PLX_ROMULUS, .subvendor = PCI_VENDOR_ID_PLX, .subdevice = PCI_DEVICE_ID_PLX_ROMULUS, @@ -3733,7 +3725,12 @@ static struct pci_device_id serial_pci_tbl[] = { { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, PCI_VENDOR_ID_PLX, PCI_SUBDEVICE_ID_UNKNOWN_0x1584, 0, 0, - pbn_b0_4_115200 }, + pbn_b2_4_115200 }, + /* Unknown card - subdevice 0x1588 */ + { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, + PCI_VENDOR_ID_PLX, + PCI_SUBDEVICE_ID_UNKNOWN_0x1588, 0, 0, + pbn_b2_8_115200 }, { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050, PCI_SUBVENDOR_ID_KEYSPAN, PCI_SUBDEVICE_ID_KEYSPAN_SX2, 0, 0, -- To unsubscribe from this list: send the line "unsubscribe linux-serial" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
