[PATCH v2 06/10] serial: sh-sci: support lower baud rate

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Takashi Yoshii <takashi.yoshii.zj@xxxxxxxxxxx>

Support prescaler 1/16 and 1/64, in addition to current 1 and 1/4.

Supporting below 2400bps was dropped long time ago in mainline.
Since then, setting lower rate has been resulting in erroneous
register value, without indicating any errors through API.

This patch adds more prescaler to support lower rates again.
This still doesn't check range, but we won't hit the case because
even 50bps at 48MHz clock is now supported.

Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@xxxxxxxxxxx>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@xxxxxxxxxxx>
---
 drivers/tty/serial/sh-sci.c | 19 ++++++++-----------
 1 file changed, 8 insertions(+), 11 deletions(-)

diff --git a/drivers/tty/serial/sh-sci.c b/drivers/tty/serial/sh-sci.c
index ffeca65..3021912 100644
--- a/drivers/tty/serial/sh-sci.c
+++ b/drivers/tty/serial/sh-sci.c
@@ -1814,7 +1814,7 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
 {
 	struct sci_port *s = to_sci_port(port);
 	struct plat_sci_reg *reg;
-	unsigned int baud, smr_val, max_baud;
+	unsigned int baud, smr_val, max_baud, cks;
 	int t = -1;
 
 	/*
@@ -1848,21 +1848,18 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
 
 	uart_update_timeout(port, termios->c_cflag, baud);
 
-	serial_port_out(port, SCSMR, smr_val);
+	for (cks = 0; t >= 256 && cks <= 3; cks++)
+		t >>= 2;
 
-	dev_dbg(port->dev, "%s: SMR %x, t %x, SCSCR %x\n", __func__, smr_val, t,
-		s->cfg->scscr);
+	dev_dbg(port->dev, "%s: SMR %x, cks %x, t %x, SCSCR %x\n",
+		__func__, smr_val, cks, t, s->cfg->scscr);
 
 	if (t >= 0) {
-		if (t >= 256) {
-			serial_port_out(port, SCSMR, (serial_port_in(port, SCSMR) & ~3) | 1);
-			t >>= 2;
-		} else
-			serial_port_out(port, SCSMR, serial_port_in(port, SCSMR) & ~3);
-
+		serial_port_out(port, SCSMR, (smr_val & ~3) | cks);
 		serial_port_out(port, SCBRR, t);
 		udelay((1000000+(baud-1)) / baud); /* Wait one bit interval */
-	}
+	} else
+		serial_port_out(port, SCSMR, smr_val);
 
 	sci_init_pins(port, termios->c_cflag);
 
-- 
1.7.12.4

--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [Kernel Newbies]     [Security]     [Netfilter]     [Bugtraq]     [Linux PPP]     [Linux FS]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Samba]     [Video 4 Linux]     [Linmodem]     [Device Mapper]     [Linux Kernel for ARM]

  Powered by Linux