This patchset implements COMMON_CLK support for the zynq. At this
point, only the basic fundamental clocks are modelled, and only
passively; for rate calculation. of_clk bindings are implemented to
allow specifying clock/peripheral relationships in the device tree.
Patch 1 and 2 are a followup to my early patch: "ARM: zynq: move ttc
timer code to drivers/clocksource". Patch 1 moves the definition
sys_timer definition out of the ttc code, and into the zynq common code.
Patch 2 is the actual rename, and makefile cleanup.
Patch 3 adds a description of the second uart to zynq-ep107.dts. I did
this pre-split (patch 4), because I felt it might make reviewing easier.
Patch 4 uses zynq-ep107.dts as a reference to create zynq-7000.dtsi,
which is intended to be a common dtsi snippet for inclusion in
describing zynq-7000 based boards. zynq-zc702.dts is created as an
example consumer. The zynq-ep107.dts file is removed entirely (it
describes, presumably, a board not available to consumers).
Patch 5 is the real meat; it adds an implementation of the clk models
for the PLLs, the CPU clock network, and basic (simplified) clk models
for the essential peripherals (UART and the TTC).
Patch 6 removes CONFIG_OF conditional code from the xilinx uart driver.
The zynq kernel requires CONFIG_OF, and this hardware is not currently
used on any other non CONFIG_OF platform.
Patch 7 adds support to the xilinx_uartps driver to allow getting clock
rate information form the device tree.
Patch 8 implements DT support for the ttc, including pulling clock tree
info.
---
There are some specific concerns that I had that I would like some
guidance on:
Two identical timers on the board have historically been statically
allocated to act as the system clocksource, and the clockevent_device.
With patch 8, this distinction is done in the device tree by tweaking
with the compatible properties of which of the timers you want used for
what purpose.
I feel, however, that this is an abuse of the device tree, which should
only be used to describe hardware, not to layout a policy on how the
hardware is used.
So, if it's not in the device tree, then where? Do I go back to the
static allocation routine, such that the first matching ttc node in the
tree becomes the clockevent_device, and the second one a clocksource?
That seems like a hack.
Is it somehow possible to have all of the timers registered as both a
clocksource and a clockevent_device, and have some higher level logic
make the policy decision as to which timer is used for what?
An additional question regarding of_clk bindings:
my_clock {
#clock-cells = <0>;
clock-output-names = "my_out_clock";
};
node_a {
clocks = <&clk>;
clock-names = "my_clock";
clock-ranges;
node_b {
/* ... */
};
};
In this scenario, should I be expecting of_clk_get(node_b, 0) to
retrieve a handle to parent's consumed clock (due to clock-ranges)? I
could make this work using of_clk_get_by_name(node_b, "my_clock"), but I
was somewhat surprised the former didn't work.
Thanks (and sorry for the novel),
Josh
---
Josh Cartwright (8):
ARM: zynq: move arm-specific sys_timer out of ttc
ARM: zynq: move ttc timer code to drivers/clocksource
ARM: zynq: dts: add description of the second uart
ARM: zynq: dts: split up device tree
ARM: zynq: add COMMON_CLK support
serial: xilinx_uartps: kill CONFIG_OF conditional
serial: xilinx_uartps: get clock rate info from dts
clocksource: xilinx_ttc: add OF_CLK support
.../devicetree/bindings/clock/zynq-7000.txt | 55 ++++
arch/arm/Kconfig | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/zynq-7000.dtsi | 166 ++++++++++
arch/arm/boot/dts/zynq-ep107.dts | 63 ----
arch/arm/boot/dts/zynq-zc702.dts | 44 +++
arch/arm/mach-zynq/Makefile | 2 +-
arch/arm/mach-zynq/common.c | 29 +-
arch/arm/mach-zynq/timer.c | 298 -----------------
drivers/clk/Makefile | 1 +
drivers/clk/clk-zynq.c | 355 +++++++++++++++++++++
drivers/clocksource/Makefile | 1 +
drivers/clocksource/xilinx_ttc.c | 326 +++++++++++++++++++
drivers/tty/serial/xilinx_uartps.c | 39 +--
include/linux/clk/zynq.h | 24 ++
.../common.h => include/linux/xilinx_ttc.h | 8 +-
16 files changed, 1022 insertions(+), 391 deletions(-)
create mode 100644 Documentation/devicetree/bindings/clock/zynq-7000.txt
create mode 100644 arch/arm/boot/dts/zynq-7000.dtsi
delete mode 100644 arch/arm/boot/dts/zynq-ep107.dts
create mode 100644 arch/arm/boot/dts/zynq-zc702.dts
delete mode 100644 arch/arm/mach-zynq/timer.c
create mode 100644 drivers/clk/clk-zynq.c
create mode 100644 drivers/clocksource/xilinx_ttc.c
create mode 100644 include/linux/clk/zynq.h
rename arch/arm/mach-zynq/common.h => include/linux/xilinx_ttc.h (81%)
--
1.8.0
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
