commit 2655a2c76f80d91da34faa8f4e114d1793435ed3 ("8250: use the 8250
register interface not the legacy one") forgot to fully switch one
instance of struct uart_port to struct uart_8250_port, causing the
following compile failure:
drivers/tty/serial/8250/8250_hp300.c: In function ‘hpdca_init_one’:
drivers/tty/serial/8250/8250_hp300.c:174: error: ‘uart’ undeclared (first use in this function)
drivers/tty/serial/8250/8250_hp300.c:174: error: (Each undeclared identifier is reported only once
drivers/tty/serial/8250/8250_hp300.c:174: error: for each function it appears in.)
This went unnoticed in -next, as CONFIG_HPDCA is not set to y by
allmodconfig.
Signed-off-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>
---
Only compile-tested, due to lack of hardware
drivers/tty/serial/8250/8250_hp300.c | 20 ++++++++++----------
1 files changed, 10 insertions(+), 10 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_hp300.c b/drivers/tty/serial/8250/8250_hp300.c
index 8f1dd2c..f3d0edf 100644
--- a/drivers/tty/serial/8250/8250_hp300.c
+++ b/drivers/tty/serial/8250/8250_hp300.c
@@ -162,7 +162,7 @@ int __init hp300_setup_serial_console(void)
static int __devinit hpdca_init_one(struct dio_dev *d,
const struct dio_device_id *ent)
{
- struct uart_port port;
+ struct uart_8250_port uart;
int line;
#ifdef CONFIG_SERIAL_8250_CONSOLE
@@ -174,19 +174,19 @@ static int __devinit hpdca_init_one(struct dio_dev *d,
memset(&uart, 0, sizeof(uart));
/* Memory mapped I/O */
- port.iotype = UPIO_MEM;
- port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
- port.irq = d->ipl;
- port.uartclk = HPDCA_BAUD_BASE * 16;
- port.mapbase = (d->resource.start + UART_OFFSET);
- port.membase = (char *)(port.mapbase + DIO_VIRADDRBASE);
- port.regshift = 1;
- port.dev = &d->dev;
+ uart.port.iotype = UPIO_MEM;
+ uart.port.flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF;
+ uart.port.irq = d->ipl;
+ uart.port.uartclk = HPDCA_BAUD_BASE * 16;
+ uart.port.mapbase = (d->resource.start + UART_OFFSET);
+ uart.port.membase = (char *)(uart.port.mapbase + DIO_VIRADDRBASE);
+ uart.port.regshift = 1;
+ uart.port.dev = &d->dev;
line = serial8250_register_8250_port(&uart);
if (line < 0) {
printk(KERN_NOTICE "8250_hp300: register_serial() DCA scode %d"
- " irq %d failed\n", d->scode, port.irq);
+ " irq %d failed\n", d->scode, uart.port.irq);
return -ENOMEM;
}
--
1.7.0.4
--
To unsubscribe from this list: send the line "unsubscribe linux-serial" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
