Hi, I run an older box as server for a couple of serial consoles, so I equipped it with a Titan Electronics Inc VScom 800L. now I installed debian lenny on the box and after some trouble with this card I compiled a vanilla 2.6.32.15 kernel. The board is a ASUS A7V333 ACPI BIOS Revision 1017. Interrupts are handled by APIC. The card is recognised properly, setserial on system startup runs smoothly. But when I access the first port on the card with minicom I get a kernel oops: [ 426.358233] irq 17: nobody cared (try booting with the "irqpoll" option) [ 426.358773] Pid: 0, comm: swapper Not tainted 2.6.32.15-1-k7 #1 [ 426.359244] Call Trace: [ 426.359453] [<c103b7b0>] ? __report_bad_irq+0x24/0x69 [ 426.359865] [<c103b7b7>] ? __report_bad_irq+0x2b/0x69 [ 426.360001] [<c103b8dc>] ? note_interrupt+0xe7/0x13f [ 426.360001] [<c103bd67>] ? handle_fasteoi_irq+0x63/0x75 [ 426.360001] [<c1004177>] ? handle_irq+0x17/0x1c [ 426.360001] [<c1003d99>] ? do_IRQ+0x2b/0x76 [ 426.360001] [<c1002e29>] ? common_interrupt+0x29/0x30 [ 426.360001] [<c10072cc>] ? default_idle+0x25/0x38 [ 426.360001] [<c1001b4a>] ? cpu_idle+0x19/0x2f [ 426.360001] [<c12e066e>] ? start_kernel+0x25f/0x262 [ 426.360001] handlers: [ 426.360001] [<c113482b>] (serial8250_interrupt+0x0/0xad) [ 426.360001] Disabling IRQ #17 Afterwards I can use all ports of the card. and /proc/interrupts shows 0: 44 IO-APIC-edge timer 1: 4014 IO-APIC-edge i8042 3: 11 IO-APIC-edge 4: 15 IO-APIC-edge 6: 3 IO-APIC-edge floppy 8: 2 IO-APIC-edge rtc0 9: 0 IO-APIC-fasteoi acpi 14: 73703 IO-APIC-edge pata_via 15: 360 IO-APIC-edge pata_via 16: 59904 IO-APIC-fasteoi eth0 17: 177327 IO-APIC-fasteoi serial 21: 0 IO-APIC-fasteoi uhci_hcd:usb1, uhci_hcd:usb2 NMI: 0 Non-maskable interrupts LOC: 21098426 Local timer interrupts SPU: 0 Spurious interrupts PMI: 0 Performance monitoring interrupts PND: 0 Performance pending work TRM: 0 Thermal event interrupts THR: 0 Threshold APIC interrupts MCE: 0 Machine check exceptions MCP: 265 Machine check polls ERR: 0 MIS: 0 Use of the suggested irqpoll didn't make things better. I append my dmesg and lspci. Could anybody have a look at this, please? Should I be worried about this? Best regards Gerold
[ 0.000000] Linux version 2.6.32.15-1-k7 (root@egeria) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 Wed Jun 23 23:27:47 CEST 2010 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000001fffc000 (usable) [ 0.000000] BIOS-e820: 000000001fffc000 - 000000001ffff000 (ACPI data) [ 0.000000] BIOS-e820: 000000001ffff000 - 0000000020000000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) [ 0.000000] DMI 2.3 present. [ 0.000000] last_pfn = 0x1fffc max_arch_pfn = 0x100000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-EFFFF uncachable [ 0.000000] F0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask FE0000000 write-back [ 0.000000] 1 disabled [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 base 0F8000000 mask FFC000000 write-combining [ 0.000000] e820 update range: 0000000000001000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] Scanning 1 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000001000 (usable) [ 0.000000] modified: 0000000000001000 - 0000000000010000 (reserved) [ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable) [ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] modified: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 000000001fffc000 (usable) [ 0.000000] modified: 000000001fffc000 - 000000001ffff000 (ACPI data) [ 0.000000] modified: 000000001ffff000 - 0000000020000000 (ACPI NVS) [ 0.000000] modified: 00000000fec00000 - 00000000fec01000 (reserved) [ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] modified: 00000000ffff0000 - 0000000100000000 (reserved) [ 0.000000] initial memory mapped : 0 - 01800000 [ 0.000000] init_memory_mapping: 0000000000000000-000000001fffc000 [ 0.000000] 0000000000 - 0000400000 page 4k [ 0.000000] 0000400000 - 001fc00000 page 2M [ 0.000000] 001fc00000 - 001fffc000 page 4k [ 0.000000] kernel direct mapping tables up to 1fffc000 @ 10000-15000 [ 0.000000] RAMDISK: 1fe5e000 - 1ffebd99 [ 0.000000] ACPI: RSDP 000f5c10 00014 (v00 ASUS ) [ 0.000000] ACPI: RSDT 1fffc000 00030 (v01 ASUS A7V333 42302E31 MSFT 31313031) [ 0.000000] ACPI: FACP 1fffc0b2 00074 (v01 ASUS A7V333 42302E31 MSFT 31313031) [ 0.000000] ACPI: DSDT 1fffc126 02124 (v01 ASUS A7V333 00001000 MSFT 0100000B) [ 0.000000] ACPI: FACS 1ffff000 00040 [ 0.000000] ACPI: BOOT 1fffc030 00028 (v01 ASUS A7V333 42302E31 MSFT 31313031) [ 0.000000] ACPI: APIC 1fffc058 0005A (v01 ASUS A7V333 42302E31 MSFT 31313031) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 511MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 1fffc000 [ 0.000000] low ram: 0 - 1fffc000 [ 0.000000] node 0 low ram: 00000000 - 1fffc000 [ 0.000000] node 0 bootmap 00011000 - 00015000 [ 0.000000] (7 early reservations) ==> bootmem [0000000000 - 001fffc000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0001000000 - 0001375940] TEXT DATA BSS ==> [0001000000 - 0001375940] [ 0.000000] #2 [001fe5e000 - 001ffebd99] RAMDISK ==> [001fe5e000 - 001ffebd99] [ 0.000000] #3 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] [ 0.000000] #4 [0001376000 - 000137c148] BRK ==> [0001376000 - 000137c148] [ 0.000000] #5 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000] [ 0.000000] #6 [0000011000 - 0000015000] BOOTMAP ==> [0000011000 - 0000015000] [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00001000 [ 0.000000] Normal 0x00001000 -> 0x0001fffc [ 0.000000] HighMem 0x0001fffc -> 0x0001fffc [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00000001 [ 0.000000] 0: 0x00000010 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x0001fffc [ 0.000000] On node 0 totalpages: 130956 [ 0.000000] free_area_init_node: node 0, pgdat c12dc2cc, node_mem_map c137e000 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3952 pages, LIFO batch:0 [ 0.000000] Normal zone: 992 pages used for memmap [ 0.000000] Normal zone: 125980 pages, LIFO batch:31 [ 0.000000] Using APIC driver default [ 0.000000] ACPI: PM-Timer IO Port: 0xe408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 2, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] nr_irqs_gsi: 24 [ 0.000000] Allocating PCI resources starting at 20000000 (gap: 20000000:dec00000) [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129932 [ 0.000000] Kernel command line: root=/dev/sda1 ro vga=791 [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] Initializing HighMem for node 0 (00000000:00000000) [ 0.000000] Memory: 513832k/524272k available (1972k kernel code, 9684k reserved, 968k data, 312k init, 0k highmem) [ 0.000000] virtual kernel memory layout: [ 0.000000] fixmap : 0xfffa4000 - 0xfffff000 ( 364 kB) [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 0.000000] vmalloc : 0xe07fc000 - 0xff7fe000 ( 496 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdfffc000 ( 511 MB) [ 0.000000] .init : 0xc12e0000 - 0xc132e000 ( 312 kB) [ 0.000000] .data : 0xc11ed080 - 0xc12df0f0 ( 968 kB) [ 0.000000] .text : 0xc1000000 - 0xc11ed080 (1972 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:288 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 1401.727 MHz processor. [ 0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 2803.45 BogoMIPS (lpj=5606908) [ 0.004073] Mount-cache hash table entries: 512 [ 0.004220] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 0.004229] CPU: L2 Cache: 256K (64 bytes/line) [ 0.004238] mce: CPU supports 4 MCE banks [ 0.004264] CPU: AMD Athlon(TM) XP 1600+ stepping 02 [ 0.004277] Checking 'hlt' instruction... OK. [ 0.020250] ACPI: Core revision 20090903 [ 0.024671] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.025696] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.068000] NET: Registered protocol family 16 [ 0.068000] ACPI: bus type pci registered [ 0.068000] PCI: PCI BIOS revision 2.10 entry at 0xf17e0, last bus=1 [ 0.068000] PCI: Using configuration type 1 for base access [ 0.068864] bio: create slab <bio-0> at 0 [ 0.069344] ACPI: EC: Look up EC in DSDT [ 0.074231] ACPI: Interpreter enabled [ 0.074257] ACPI: (supports S0 S1 S5) [ 0.074286] ACPI: Using IOAPIC for interrupt routing [ 0.081530] ACPI: No dock devices found. [ 0.081706] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.081810] pci 0000:00:00.0: reg 10 32bit mmio pref: [0xf8000000-0xfbffffff] [ 0.081905] pci 0000:00:01.0: supports D1 [ 0.081942] pci 0000:00:05.0: reg 10 io port: [0xd800-0xd8ff] [ 0.081984] pci 0000:00:05.0: supports D1 D2 [ 0.082025] pci 0000:00:0d.0: reg 10 io port: [0xd400-0xd4ff] [ 0.082033] pci 0000:00:0d.0: reg 14 32bit mmio: [0xf4800000-0xf48000ff] [ 0.082057] pci 0000:00:0d.0: reg 30 32bit mmio pref: [0x000000-0x00ffff] [ 0.082075] pci 0000:00:0d.0: supports D1 D2 [ 0.082079] pci 0000:00:0d.0: PME# supported from D1 D2 D3hot D3cold [ 0.082090] pci 0000:00:0d.0: PME# disabled [ 0.082117] pci 0000:00:0e.0: reg 10 io port: [0xd000-0xd007] [ 0.082125] pci 0000:00:0e.0: reg 14 io port: [0xb800-0xb807] [ 0.082133] pci 0000:00:0e.0: reg 18 io port: [0xb400-0xb407] [ 0.082141] pci 0000:00:0e.0: reg 1c io port: [0xb000-0xb007] [ 0.082150] pci 0000:00:0e.0: reg 20 io port: [0xa800-0xa83f] [ 0.082278] pci 0000:00:11.1: reg 20 io port: [0xa400-0xa40f] [ 0.082349] pci 0000:00:11.2: reg 20 io port: [0xa000-0xa01f] [ 0.082416] pci 0000:00:11.3: reg 20 io port: [0x9800-0x981f] [ 0.082491] pci 0000:01:00.0: reg 10 32bit mmio: [0xf5000000-0xf5ffffff] [ 0.082499] pci 0000:01:00.0: reg 14 32bit mmio pref: [0xf7000000-0xf7ffffff] [ 0.082518] pci 0000:01:00.0: reg 30 32bit mmio pref: [0xf6c00000-0xf6ffffff] [ 0.082563] pci 0000:00:01.0: bridge 32bit mmio: [0xf5000000-0xf6afffff] [ 0.082570] pci 0000:00:01.0: bridge 32bit mmio pref: [0xf6c00000-0xf7ffffff] [ 0.082580] pci_bus 0000:00: on NUMA node 0 [ 0.082587] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.082798] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] [ 0.084371] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) [ 0.084511] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.084641] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.084769] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. [ 0.084897] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 *12 14) [ 0.085137] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none [ 0.085148] vgaarb: loaded [ 0.085401] SCSI subsystem initialized [ 0.085446] libata version 3.00 loaded. [ 0.085559] usbcore: registered new interface driver usbfs [ 0.085651] usbcore: registered new interface driver hub [ 0.085713] usbcore: registered new device driver usb [ 0.085935] PCI: Using ACPI for IRQ routing [ 0.086174] Switching to clocksource tsc [ 0.086222] pnp: PnP ACPI init [ 0.086237] ACPI: bus type pnp registered [ 0.089090] pnp: PnP ACPI: found 13 devices [ 0.089101] ACPI: ACPI bus type pnp unregistered [ 0.089110] PnPBIOS: Disabled by ACPI PNP [ 0.089131] system 00:00: iomem range 0x0-0x9ffff could not be reserved [ 0.089141] system 00:00: iomem range 0xf0000-0xfffff could not be reserved [ 0.089151] system 00:00: iomem range 0x100000-0x1fffffff could not be reserved [ 0.089161] system 00:00: iomem range 0xfec00000-0xfec000ff could not be reserved [ 0.089171] system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.089186] system 00:02: ioport range 0xe400-0xe47f has been reserved [ 0.089195] system 00:02: ioport range 0xe800-0xe81f has been reserved [ 0.089204] system 00:02: iomem range 0xfff80000-0xffffffff could not be reserved [ 0.089215] system 00:02: iomem range 0xffb80000-0xffbfffff has been reserved [ 0.089229] system 00:03: ioport range 0x4d0-0x4d1 has been reserved [ 0.089243] system 00:0c: ioport range 0x290-0x291 has been reserved [ 0.089252] system 00:0c: ioport range 0x370-0x372 has been reserved [ 0.124519] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 [ 0.124531] pci 0000:00:01.0: IO window: disabled [ 0.124541] pci 0000:00:01.0: MEM window: 0xf5000000-0xf6afffff [ 0.124551] pci 0000:00:01.0: PREFETCH window: 0xf6c00000-0xf7ffffff [ 0.124575] pci 0000:00:01.0: setting latency timer to 64 [ 0.124583] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.124588] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] [ 0.124594] pci_bus 0000:01: resource 1 mem: [0xf5000000-0xf6afffff] [ 0.124598] pci_bus 0000:01: resource 2 pref mem [0xf6c00000-0xf7ffffff] [ 0.124669] NET: Registered protocol family 2 [ 0.124811] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.125268] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.125523] TCP bind hash table entries: 16384 (order: 4, 65536 bytes) [ 0.125677] TCP: Hash tables configured (established 16384 bind 16384) [ 0.125686] TCP reno registered [ 0.125774] NET: Registered protocol family 1 [ 0.125803] pci 0000:00:01.0: disabling DAC on VIA PCI bridge [ 0.125879] pci 0000:01:00.0: Boot video device [ 0.125952] Trying to unpack rootfs image as initramfs... [ 0.208623] Freeing initrd memory: 1591k freed [ 0.211713] Simple Boot Flag at 0x3a set to 0x1 [ 0.212259] Scanning for low memory corruption every 60 seconds [ 0.212789] HugeTLB registered 4 MB page size, pre-allocated 0 pages [ 0.212876] VFS: Disk quotas dquot_6.5.2 [ 0.212931] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.213030] msgmni has been set to 1007 [ 0.213222] alg: No test for stdrng (krng) [ 0.213295] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.213307] io scheduler noop registered [ 0.213313] io scheduler anticipatory registered [ 0.213319] io scheduler deadline registered [ 0.213334] io scheduler cfq registered (default) [ 0.213634] vesafb: framebuffer at 0xf7000000, mapped to 0xe0880000, using 3072k, total 4096k [ 0.213647] vesafb: mode is 1024x768x16, linelength=2048, pages=0 [ 0.213654] vesafb: protected mode interface info at c000:4d96 [ 0.213662] vesafb: pmi: set display start = c00c4dbd, set palette = c00c4e1f [ 0.213669] vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da [ 0.213695] vesafb: scrolling: redraw [ 0.213703] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 [ 0.255810] Console: switching to colour frame buffer device 128x48 [ 0.294071] fb0: VESA VGA frame buffer device [ 0.294513] isapnp: Scanning for PnP cards... [ 0.604838] isapnp: No Plug & Play device found [ 0.609060] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.609713] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.610367] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.611988] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.612627] 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.613234] serial 0000:00:0e.0: enabling device (0000 -> 0001) [ 0.613722] serial 0000:00:0e.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.614800] 0000:00:0e.0: ttyS4 at I/O 0xb800 (irq = 17) is a 16550A [ 0.615470] 0000:00:0e.0: ttyS5 at I/O 0xb400 (irq = 17) is a 16550A [ 0.616126] 0000:00:0e.0: ttyS6 at I/O 0xa800 (irq = 17) is a 16550A [ 0.616781] 0000:00:0e.0: ttyS7 at I/O 0xa808 (irq = 17) is a 16550A [ 0.617435] 0000:00:0e.0: ttyS8 at I/O 0xa810 (irq = 17) is a 16550A [ 0.618104] 0000:00:0e.0: ttyS9 at I/O 0xa818 (irq = 17) is a 16550A [ 0.618760] 0000:00:0e.0: ttyS10 at I/O 0xa820 (irq = 17) is a 16550A [ 0.619421] 0000:00:0e.0: ttyS11 at I/O 0xa828 (irq = 17) is a 16550A [ 0.634331] brd: module loaded [ 0.646800] Uniform Multi-Platform E-IDE driver [ 0.659519] pata_via 0000:00:11.1: version 0.3.4 [ 0.659542] pata_via 0000:00:11.1: can't derive routing for PCI INT A [ 0.672472] scsi0 : pata_via [ 0.685089] scsi1 : pata_via [ 0.698171] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xa400 irq 14 [ 0.710621] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xa408 irq 15 [ 0.722971] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.735356] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.747625] uhci_hcd: USB Universal Host Controller Interface driver [ 0.759775] uhci_hcd 0000:00:11.2: PCI INT D -> GSI 21 (level, low) -> IRQ 21 [ 0.772086] uhci_hcd 0000:00:11.2: UHCI Host Controller [ 0.784375] uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1 [ 0.796989] uhci_hcd 0000:00:11.2: irq 21, io base 0x0000a000 [ 0.809655] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.822356] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.834908] usb usb1: Product: UHCI Host Controller [ 0.847258] usb usb1: Manufacturer: Linux 2.6.32.15-1-k7 uhci_hcd [ 0.859693] usb usb1: SerialNumber: 0000:00:11.2 [ 0.872056] usb usb1: configuration #1 chosen from 1 choice [ 0.884381] hub 1-0:1.0: USB hub found [ 0.896370] hub 1-0:1.0: 2 ports detected [ 0.908358] uhci_hcd 0000:00:11.3: PCI INT D -> GSI 21 (level, low) -> IRQ 21 [ 0.920627] uhci_hcd 0000:00:11.3: UHCI Host Controller [ 0.932628] uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2 [ 0.944706] uhci_hcd 0000:00:11.3: irq 21, io base 0x00009800 [ 0.956755] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 0.969052] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 0.981321] usb usb2: Product: UHCI Host Controller [ 0.993447] usb usb2: Manufacturer: Linux 2.6.32.15-1-k7 uhci_hcd [ 1.005924] usb usb2: SerialNumber: 0000:00:11.3 [ 1.018338] usb usb2: configuration #1 chosen from 1 choice [ 1.031011] hub 2-0:1.0: USB hub found [ 1.043437] hub 2-0:1.0: 2 ports detected [ 1.055980] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 [ 1.068388] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp [ 1.082409] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.096006] mice: PS/2 mouse device common for all mice [ 1.109753] rtc_cmos 00:05: RTC can wake from S4 [ 1.123740] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 [ 1.137986] rtc0: alarms up to one month, 242 bytes nvram [ 1.152247] cpuidle: using governor ladder [ 1.167226] TCP cubic registered [ 1.181418] NET: Registered protocol family 17 [ 1.195695] Using IPI Shortcut mode [ 1.210442] rtc_cmos 00:05: setting system clock to 2010-06-24 19:16:40 UTC (1277407000) [ 1.231170] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 1.247813] ata1.00: ATA-5: WDC WD400BB-00GFA0, 09.01B09, max UDMA/100 [ 1.262977] ata1.00: 78165360 sectors, multi 16: LBA [ 1.278333] ata1.01: ATAPI: _NEC DVD_RW ND-1300A, 1.0B, max UDMA/33 [ 1.307200] ata1.00: configured for UDMA/100 [ 1.338124] ata1.01: configured for UDMA/33 [ 1.353435] scsi 0:0:0:0: Direct-Access ATA WDC WD400BB-00GF 09.0 PQ: 0 ANSI: 5 [ 1.372068] scsi 0:0:1:0: CD-ROM _NEC DVD_RW ND-1300A 1.0B PQ: 0 ANSI: 5 [ 1.556479] ata2.00: ATA-7: SAMSUNG SP1604N, TM100-24, max UDMA/100 [ 1.571827] ata2.00: 312581808 sectors, multi 16: LBA48 [ 1.587157] ata2.01: ATAPI: SONY SDX-260V, 0100, max UDMA/100 [ 1.608329] ata2.00: configured for UDMA/100 [ 1.636325] ata2.01: configured for UDMA/100 [ 1.686103] scsi 1:0:0:0: Direct-Access ATA SAMSUNG SP1604N TM10 PQ: 0 ANSI: 5 [ 1.702437] scsi 1:0:1:0: Sequential-Access SONY SDX-260V 0100 PQ: 0 ANSI: 2 [ 1.717867] Freeing unused kernel memory: 312k freed [ 1.808234] ide-gd driver 1.18 [ 2.168323] sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB) [ 2.190907] sd 1:0:0:0: [sdb] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 2.313215] sd 0:0:0:0: [sda] Write Protect is off [ 2.329746] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.352153] sd 1:0:0:0: [sdb] Write Protect is off [ 2.368286] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 2.426272] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.442895] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.459258] sda: [ 2.459656] sdb: sda1 sda2 < sdb1 [ 2.499411] sd 1:0:0:0: [sdb] Attached SCSI disk [ 2.515310] sda5 > [ 2.533429] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.906989] kjournald starting. Commit interval 5 seconds [ 2.922789] EXT3-fs: mounted filesystem with ordered data mode. [ 4.655342] udevd version 125 started [ 5.568123] Linux agpgart interface v0.103 [ 5.600657] input: PC Speaker as /devices/platform/pcspkr/input/input1 [ 5.767907] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 5.833714] Floppy drive(s): fd0 is 1.44M [ 5.886125] st: Version 20081215, fixed bufsize 32768, s/g segs 256 [ 5.934102] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray [ 5.950852] Uniform CD-ROM driver Revision: 3.20 [ 6.000418] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2 [ 6.018043] processor LNXCPU:00: registered as cooling_device0 [ 6.084130] r8169 0000:00:0d.0: enabling device (0014 -> 0017) [ 6.101104] r8169 0000:00:0d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 6.175788] FDC 0 is a post-1991 82077 [ 6.248132] ACPI: Power Button [PWRB] [ 6.480202] sr 0:0:1:0: Attached scsi CD-ROM sr0 [ 6.480502] st 1:0:1:0: Attached scsi tape st0 [ 6.497422] st 1:0:1:0: st0: try direct i/o: yes (alignment 4 B) [ 6.532194] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 [ 6.640551] r8169 0000:00:0d.0: no PCI Express capability [ 6.776113] ACPI: Power Button [PWRF] [ 6.844709] eth0: RTL8110s at 0xe0ca4000, 00:11:6b:35:bb:77, XID 04000000 IRQ 16 [ 6.904315] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 7.024535] osst :I: Tape driver with OnStream support version 0.99.4 [ 7.024538] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $ [ 7.100157] sr 0:0:1:0: Attached scsi generic sg1 type 5 [ 7.116873] agpgart: Detected VIA KT266/KY266x/KT333 chipset [ 7.273813] sd 1:0:0:0: Attached scsi generic sg2 type 0 [ 7.292097] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xf8000000 [ 7.484783] st 1:0:1:0: Attached scsi generic sg3 type 1 [ 8.702518] Adding 1510068k swap on /dev/sda5. Priority:-1 extents:1 across:1510068k [ 9.187772] EXT3 FS on sda1, internal journal [ 9.715330] loop: module loaded [ 10.414382] kjournald starting. Commit interval 5 seconds [ 10.431758] EXT3 FS on sdb1, internal journal [ 10.448988] EXT3-fs: mounted filesystem with ordered data mode. [ 11.652404] r8169: eth0: link up
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333] Subsystem: ASUSTeK Computer Inc. A7V333 Mainboard Flags: bus master, 66MHz, medium devsel, latency 0 Memory at f8000000 (32-bit, prefetchable) [size=64M] Capabilities: [a0] AGP version 2.0 Capabilities: [c0] Power Management version 2 Kernel driver in use: agpgart-via Kernel modules: via-agp 00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP] (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: f5000000-f6afffff Prefetchable memory behind bridge: f6c00000-f7ffffff Capabilities: [80] Power Management version 2 00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10) Subsystem: ASUSTeK Computer Inc. CMI8738 6ch-MX Flags: bus master, stepping, medium devsel, latency 32, IRQ 255 I/O ports at d800 [disabled] [size=256] Capabilities: [c0] Power Management version 2 00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 I/O ports at d400 [size=256] Memory at f4800000 (32-bit, non-prefetchable) [size=256] [virtual] Expansion ROM at 20000000 [disabled] [size=64K] Capabilities: [dc] Power Management version 2 Kernel driver in use: r8169 Kernel modules: r8169 00:0e.0 Serial controller: Titan Electronics Inc VScom 800L 8 port serial adaptor (prog-if 02 [16550]) Subsystem: Titan Electronics Inc VScom 800L 8 port serial adaptor Flags: medium devsel, IRQ 17 I/O ports at d000 [size=8] I/O ports at b800 [size=8] I/O ports at b400 [size=8] I/O ports at b000 [size=8] I/O ports at a800 [size=64] Kernel driver in use: serial 00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge Subsystem: ASUSTeK Computer Inc. A7V333 motherboard Flags: bus master, stepping, medium devsel, latency 0 Capabilities: [c0] Power Management version 2 Kernel modules: i2c-viapro 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP]) Subsystem: ASUSTeK Computer Inc. A7V8X / A7V333 motherboard Flags: bus master, medium devsel, latency 32 [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] I/O ports at a400 [size=16] Capabilities: [c0] Power Management version 2 Kernel driver in use: pata_via Kernel modules: via82cxxx 00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 23) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. VT6202 USB2.0 4 port controller Flags: bus master, medium devsel, latency 32, IRQ 21 I/O ports at a000 [size=32] Capabilities: [80] Power Management version 2 Kernel driver in use: uhci_hcd 00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 23) (prog-if 00 [UHCI]) Subsystem: ASUSTeK Computer Inc. VT6202 USB2.0 4 port controller Flags: bus master, medium devsel, latency 32, IRQ 21 I/O ports at 9800 [size=32] Capabilities: [80] Power Management version 2 Kernel driver in use: uhci_hcd 01:00.0 VGA compatible controller: NVidia / SGS Thomson (Joint Venture) Riva128 (rev 10) (prog-if 00 [VGA controller]) Subsystem: Elsa AG VICTORY Erazor Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11 Memory at f5000000 (32-bit, non-prefetchable) [size=16M] Memory at f7000000 (32-bit, prefetchable) [size=16M] Expansion ROM at f6c00000 [disabled] [size=4M] Capabilities: [44] AGP version 1.0
