Hi,
On 2/3/2016 3:39 PM, Arnd Bergmann wrote:
> On Wednesday 03 February 2016 15:01:34 Joao Pinto wrote:
>>
>> Hi Arnd,
>>
>> On 2/3/2016 12:54 PM, Arnd Bergmann wrote:
>>> On Wednesday 03 February 2016 11:28:26 Joao Pinto wrote:
>>>>
>>>> Signed-off-by: Joao Pinto <jpinto@xxxxxxxxxxxx>
>>>
>>> This needs a changelog comment, like every patch.
>>>
>>>> @@ -0,0 +1,16 @@
>>>> +* Universal Flash Storage (UFS) DesignWare Host Controller
>>>> +
>>>> +DWC_UFSHC nodes are defined to describe on-chip UFS host controllers.
>>>> +Each UFS controller instance should have its own node.
>>>> +
>>>> +Required properties:
>>>> +- compatible : compatible list, contains "snps,ufshcd"
>>>
>>> Are there multiple versions of this controller? Usually for designware
>>> parts the version is known, so we should document which versions exist
>>
>> This controller recent releases was 2.0, but we released last year 1.1. The
>> driver works with both. The driver must work with all DWC UFS versions.
>
> Ok, then make the driver match on the "snps,ufshcd-1.1" compatible
> string, but document both strings in the binding document, and make
> it mandatory to specify the 1.1 version as a compatible fallback.
>
> If we ever need to handle a quirk for the 2.0 version then, it can
> easily be done.
We need the driver to support UFS 2.0 because it is our latest release and is
the done that Synopsys is focused now. We could call it "snps, ufshcd-2.0" then.
What do you think?
>
>>>> +config SCSI_UFS_DWC_HOOKS
>>>> + bool "DesignWare hooks to UFS controller"
>>>> + depends on SCSI_UFSHCD
>>>> + ---help---
>>>> + This selects the DesignWare hooks for the UFS host controller.
>>>> +
>>>> + Select this if you have a DesignWare UFS controller.
>>>> + If unsure, say N.
>>>
>>> This could be a silent symbol that gets selected by SCSI_UFS_DWC_PLAT
>>
>> We could do that, but imagine that we select SCSI_UFS_QCOM, then the synopsys
>> hooks would be selected also which in my opinion is not very accurate.
>> In my opinion we should have a selectable DWC_HOOKS.
>
> I don't understand. At the moment, you can enable SCSI_UFS_DWC_HOOKS
> even if nothing uses it and you only have SCSI_UFS_QCOM enabled.
SCSI_UFS_QCOM is select if you are using a QCOM and PLAT is enabled.
We can do it the following way: If DWC Platform or DWC PCI are selected than
automatically select the HOOKS. What do you think?
>
> With my suggestion, the hooks would disappear unless they are
> actually used.
>
> Then again, with my later comments, we no longer need the hooks.
>
>
>>>> +/**
>>>> + * ufshcd_dwc_setup_mphy()
>>>> + * This function configures Local (host) Synopsys MPHY specific attributes
>>>> + *
>>>> + * @hba: Pointer to drivers structure
>>>> + *
>>>> + * Returns 0 on success non-zero value on failure
>>>> + */
>>>> +int ufshcd_dwc_setup_mphy(struct ufs_hba *hba)
>>>> +{
>>>> + int ret = 0;
>>>> +
>>>> +#ifdef CONFIG_SCSI_UFS_DWC_40BIT_RMMI
>>>> + dev_info(hba->dev, "Configuring MPHY 40-bit RMMI");
>>>> + ret = ufshcd_dwc_setup_40bit_rmmi(hba);
>>>> + if (ret) {
>>>> + dev_err(hba->dev, "40-bit RMMI configuration failed");
>>>> + goto out;
>>>> + }
>>>> +#else
>>>> +#ifdef CONFIG_SCSI_UFS_DWC_20BIT_RMMI
>>>> + dev_info(hba->dev, "Configuring MPHY 20-bit RMMI");
>>>> + ret = ufshcd_dwc_setup_20bit_rmmi(hba);
>>>> + if (ret) {
>>>> + dev_err(hba->dev, "20-bit RMMI configuration failed");
>>>> + goto out;
>>>> + }
>>>> +#endif
>>>> +#endif
>>>> + /* To write Shadow register bank to effective configuration block */
>>>> + ret = ufshcd_dme_set(hba, UIC_ARG_MIB(VS_MPHYCFGUPDT), 0x01);
>>>> + if (ret)
>>>> + goto out;
>>>> +
>>>> + /* To configure Debug OMC */
>>>> + ret = ufshcd_dme_set(hba, UIC_ARG_MIB(VS_DEBUGOMC), 0x01);
>>>> +
>>>> +out:
>>>> + return ret;
>>>> +}
>>>
>>> Try to use the generic PHY abstraction here and remove all the #ifdef etc.
>>
>> Could you please point an example for me to check?
>
> drivers/phy/phy-qcom-ufs-qmp-14nm.c is a phy driver, and it gets used through
> the generic devm_phy_get()/phy_power_on()/phy_power_off()/... interfaces.
>
> This should probably be moved into the generic UFS platform driver so the PHY
> handling can be shared between all backends.
>
I will check it out.
>>>> };
>>>
>>> I think you're better off with a separate PCI driver for this. Remove
>>> all the #ifdef mess here, put whatever is dwc specific into a new file,
>>> and perhaps move the common parts into a shared file that can be used
>>> by both the samsung and designware drivers.
>>
>> I have a branch with that approach, but honestly it would be a big change in the
>> UFS arch for the pci and I decided to make it simple. I sent that suggestion for
>> the scsi mailing list and the comments showed me that. Does anyone have anything
>> against putting ufshcd-pci.c as a pci common code and then have a ufs-dwc-pci.c
>> and a ufs-samsung-pci.c that uses that common code?
>
> Another approach would be to just rename the existing file to ufs-samsung-pci.c
> and start the ufs-dwc-pci.c as a copy of that. The file is not really all that
> large anyway.
>
Yes we can do that, it is less intrusive.
> Arnd
>
Joao
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
