On Mon, Oct 26, 2015 at 10:14:33PM +0800, John Garry wrote:
> Add devicetree bindings for HiSilicon SAS driver.
>
> Signed-off-by: John Garry <john.garry@xxxxxxxxxx>
> ---
> .../devicetree/bindings/scsi/hisilicon-sas.txt | 70 ++++++++++++++++++++++
> 1 file changed, 70 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/scsi/hisilicon-sas.txt
>
> diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt
> new file mode 100644
> index 0000000..d1e7b2a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt
> @@ -0,0 +1,70 @@
> +* HiSilicon SAS controller
> +
> +The HiSilicon SAS controller supports SAS/SATA.
> +
> +Main node required properties:
> + - compatible : value should be as follows:
> + (a) "hisilicon,sas-controller-v1" for v1 of HiSilicon SAS controller IP
> + - reg : Address and length of the SAS register
> + - hisilicon,sas-syscon: phandle of syscon used for sas control
> + - ctrl-reg : offset to the following SAS control registers (in order):
> + - reset assert
> + - clock disable
> + - reset status
> + - reset de-assert
> + - clock enable
This needs a better name, and it should probably be split up into
several properties.
However, it sounds like the syscon is actually a clock+reset
controller, and should be modelled as such. It's not actually a part of
the SAS controller as such.
> + - queue-count : number of delivery and completion queues in the controller
> + - phy-count : number of phys accessible by the controller
> + - interrupts : Interrupts for phys, completion queues, and fatal
> + interrupts:
> + - Each phy has 3 interrupt sources:
> + - broadcast
> + - phyup
> + - abnormal
> + - Each completion queue has 1 interrupt source
> + - Each controller has 2 fatal interrupt sources:
> + - ECC
> + - AXI bus
Please make the ordering explicit here (you might only need to add the
phrase "in order" in a few places).
Thanks,
Mark.
> +
> +* HiSilicon SAS syscon
> +
> +Required properties:
> +- compatible: should be "hisilicon,sas-ctrl", "syscon"
> +- reg: offset and length of the syscon sas-ctrl registers
> +
> +
> +Example:
> + sas_ctrl0: sas_ctrl@c0000000 {
> + compatible = "hisilicon,sas-ctrl", "syscon";
> + reg = <0x0 0xc0000000 0x0 0x10000>;
> + };
> +
> + sas0: sas@c1000000 {
> + compatible = "hisilicon,sas-controller-v1";
> + reg = <0x0 0xc1000000 0x0 0x10000>;
> + hisilicon,sas-syscon = <&sas_ctrl0>;
> + ctrl-reg = <0xa60 0x33c 0x5a30 0xa64 0x338>;
> + queue-count = <32>;
> + phy-count = <8>;
> + dma-coherent;
> + interrupt-parent = <&mbigen_dsa>;
> + interrupts = <259 4>, <263 4>,<264 4>,/* phy irq(0~79) */
> + <269 4>,<273 4>,<274 4>,/* phy irq(0~79) */
> + <279 4>,<283 4>,<284 4>,/* phy irq(0~79) */
> + <289 4>,<293 4>,<294 4>,/* phy irq(0~79) */
> + <299 4>,<303 4>,<304 4>,/* phy irq(0~79) */
> + <309 4>,<313 4>,<314 4>,/* phy irq(0~79) */
> + <319 4>,<323 4>,<324 4>,/* phy irq(0~79) */
> + <329 4>,<333 4>,<334 4>,/* phy irq(0~79) */
> + <336 1>,<337 1>,<338 1>,<339 1>,<340 1>,
> + <341 1>,<342 1>,<343 1>,/* cq irq (80~111) */
> + <344 1>,<345 1>,<346 1>,<347 1>,<348 1>,
> + <349 1>,<350 1>,<351 1>,/* cq irq (80~111) */
> + <352 1>,<353 1>,<354 1>,<355 1>,<356 1>,
> + <357 1>,<358 1>,<359 1>,/* cq irq (80~111) */
> + <360 1>,<361 1>,<362 1>,<363 1>,<364 1>,
> + <365 1>,<366 1>,<367 1>,/* cq irq (80~111) */
> + <376 4>,/* chip fatal error irq(120) */
> + <381 4>;/* chip fatal error irq(125) */
> + status = "disabled";
> + };
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
