This change depends on draviv [PATCH v3] series of 16 changes that was already uploaded. Soon draviv will uploaded again as [PATCH v4] that contain 17 patches, and this change will be dependent on this serie, Thanks, Yaniv -----Original Message----- From: Yaniv Gardi [mailto:ygardi@xxxxxxxxxxxxxx] Sent: Wednesday, September 17, 2014 7:22 PM To: James.Bottomley@xxxxxxxxxxxxxxxxxxxxx; hch@xxxxxxxxxxxxx Cc: linux-kernel@xxxxxxxxxxxxxxx; linux-scsi@xxxxxxxxxxxxxxx; linux-arm-msm@xxxxxxxxxxxxxxx; santoshsy@xxxxxxxxx; linux-scsi-owner@xxxxxxxxxxxxxxx; subhashj@xxxxxxxxxxxxxx; ygardi@xxxxxxxxxxxxxx; noag@xxxxxxxxxxxxxx; draviv@xxxxxxxxxxxxxx; Rob Herring; Pawel Moll; Mark Rutland; Ian Campbell; Kumar Gala; Kishon Vijay Abraham I; Vinayak Holikatti; James E.J. Bottomley; Grant Likely; Raviv Shvili; Sujit Reddy Thumma; Christoph Hellwig; Sahitya Tummala; open list:OPEN FIRMWARE AND... Subject: [PATCH v4] scsi: ufs: add support of generic PHY framework in Qualcomm MSM chips In this change we add support to the generic PHY framework. Two UFS phys are implemented: qmp-20nm and qmp-28nm. Also, the files in this change implement the UFS HW (controller & PHY) specific behavior in Qualcomm chips. Relocation of a few header files is needed in order to expose routines and data structures between PHY driver and UFS driver Signed-off-by: Yaniv Gardi <ygardi@xxxxxxxxxxxxxx> --- .../devicetree/bindings/phy/qcom-ufs-phy.txt | 37 + drivers/phy/Makefile | 3 + drivers/phy/phy-qcom-ufs-qmp-20nm.c | 259 ++++++ drivers/phy/phy-qcom-ufs-qmp-20nm.h | 216 +++++ drivers/phy/phy-qcom-ufs-qmp-28nm.c | 342 ++++++++ drivers/phy/phy-qcom-ufs-qmp-28nm.h | 738 ++++++++++++++++++ drivers/phy/phy-qcom-ufs.c | 661 ++++++++++++++++ drivers/scsi/ufs/Kconfig | 12 + drivers/scsi/ufs/Makefile | 1 + drivers/scsi/ufs/ufs-qcom.c | 866 +++++++++++++++++++++ drivers/scsi/ufs/ufs.h | 491 ------------ drivers/scsi/ufs/ufshcd-pci.c | 2 +- drivers/scsi/ufs/ufshcd-pltfrm.c | 2 +- drivers/scsi/ufs/ufshcd.c | 14 +- drivers/scsi/ufs/ufshcd.h | 595 -------------- drivers/scsi/ufs/unipro.h | 207 ----- include/linux/phy/phy-qcom-ufs.h | 202 +++++ include/linux/scsi/ufs/ufs-qcom.h | 156 ++++ include/linux/scsi/ufs/ufs.h | 491 ++++++++++++ include/linux/scsi/ufs/ufshcd.h | 635 +++++++++++++++ include/linux/scsi/ufs/unipro.h | 207 +++++ 21 files changed, 4840 insertions(+), 1297 deletions(-) create mode 100644 Documentation/devicetree/bindings/phy/qcom-ufs-phy.txt create mode 100644 drivers/phy/phy-qcom-ufs-qmp-20nm.c create mode 100644 drivers/phy/phy-qcom-ufs-qmp-20nm.h create mode 100644 drivers/phy/phy-qcom-ufs-qmp-28nm.c create mode 100644 drivers/phy/phy-qcom-ufs-qmp-28nm.h create mode 100644 drivers/phy/phy-qcom-ufs.c create mode 100644 drivers/scsi/ufs/ufs-qcom.c delete mode 100644 drivers/scsi/ufs/ufs.h delete mode 100644 drivers/scsi/ufs/ufshcd.h delete mode 100644 drivers/scsi/ufs/unipro.h create mode 100644 include/linux/phy/phy-qcom-ufs.h create mode 100644 include/linux/scsi/ufs/ufs-qcom.h create mode 100644 include/linux/scsi/ufs/ufs.h create mode 100644 include/linux/scsi/ufs/ufshcd.h create mode 100644 include/linux/scsi/ufs/unipro.h diff --git a/Documentation/devicetree/bindings/phy/qcom-ufs-phy.txt b/Documentation/devicetree/bindings/phy/qcom-ufs-phy.txt new file mode 100644 index 0000000..8a6798f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-ufs-phy.txt @@ -0,0 +1,37 @@ +* QCOM Universal Flash Storage (UFS) PHY + +UFSPHY nodes are defined to describe on-chip UFS PHY hardware macro. +Each UFS PHY node should have its own node. + +To bind UFS PHY with UFS host controller, the controller node should +contain a phandle reference to UFS PHY node. + +Required properties: +- compatible : compatible list, contains "qcom,ufs-phy-qmp-28nm" + or "qcom,ufs-phy-qmp-20nm" according to the relevant + phy in use +- reg : <registers mapping> +- #phy-cells : This property shall be set to 0 +- vdda-phy-supply : phandle to main PHY supply for analog domain +- vdda-pll-supply : phandle to PHY PLL and Power-Gen block power supply + +Optional properties: +- vdda-phy-max-microamp : specifies max. load that can be drawn from phy supply +- vdda-pll-max-microamp : specifies max. load that can be drawn from pll supply + +Example: + + ufsphy1: ufsphy@0xfc597000 { + compatible = "qcom,ufs-phy-qmp-28nm"; + reg = <0xfc597000 0x800>; + #phy-cells = <0>; + vdda-phy-supply = <&pma8084_l4>; + vdda-pll-supply = <&pma8084_l12>; + vdda-phy-max-microamp = <50000>; + vdda-pll-max-microamp = <1000>; + }; + + ufshc@0xfc598000 { + ... + phys = <&ufsphy1>; + }; diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index 95c69ed..eac4854 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -28,3 +28,6 @@ obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o obj-$(CONFIG_PHY_XGENE) += phy-xgene.o +obj-$(CONFIG_SCSI_UFS_QCOM) += phy-qcom-ufs.o +obj-$(CONFIG_SCSI_UFS_QCOM) += phy-qcom-ufs-qmp-28nm.o +obj-$(CONFIG_SCSI_UFS_QCOM) += phy-qcom-ufs-qmp-20nm.o diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.c b/drivers/phy/phy-qcom-ufs-qmp-20nm.c new file mode 100644 index 0000000..b6dcf2d --- /dev/null +++ b/drivers/phy/phy-qcom-ufs-qmp-20nm.c @@ -0,0 +1,259 @@ +/* + * Copyright (c) 2013-2014, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/time.h> +#include <linux/clk.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include <linux/phy/phy-qcom-ufs.h> +#include "phy-qcom-ufs-qmp-20nm.h" + +#define UFS_PHY_NAME "ufs_phy_qmp_20nm" + +static +int ufs_qcom_phy_qmp_20nm_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy) +{ + struct ufs_qcom_phy_calibration *tbl_A, *tbl_B; + int tbl_size_A, tbl_size_B; + int rate = UFS_QCOM_LIMIT_HS_RATE; + int err; + + tbl_size_A = ARRAY_SIZE(phy_cal_table_rate_A); + tbl_A = phy_cal_table_rate_A; + + tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B); + tbl_B = phy_cal_table_rate_B; + + err = ufs_qcom_phy_calibrate(ufs_qcom_phy, tbl_A, tbl_size_A, + tbl_B, tbl_size_B, rate); + + if (err) + dev_err(ufs_qcom_phy->dev, "%s: ufs_qcom_phy_calibrate() failed %d\n", + __func__, err); + + return err; +} + +static +void ufs_qcom_phy_qmp_20nm_advertise_quirks(struct ufs_qcom_phy *phy_common) +{ + phy_common->quirks = + UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE; +} + +static int ufs_qcom_phy_qmp_20nm_init(struct phy *generic_phy) +{ + struct ufs_qcom_phy_qmp_20nm *phy = phy_get_drvdata(generic_phy); + struct ufs_qcom_phy *phy_common = &phy->common_cfg; + int err = 0; + + err = ufs_qcom_phy_init_clks(generic_phy, phy_common); + if (err) { + dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_clks() failed %d\n", + __func__, err); + goto out; + } + + err = ufs_qcom_phy_init_vregulators(generic_phy, phy_common); + if (err) { + dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_vregulators() failed %d\n", + __func__, err); + goto out; + } + + ufs_qcom_phy_qmp_20nm_advertise_quirks(phy_common); + +out: + return err; +} + +static +void ufs_qcom_phy_qmp_20nm_power_control(struct ufs_qcom_phy *phy, bool val) +{ + bool hibern8_exit_after_pwr_collapse = phy->quirks & + UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE; + + if (val) { + writel_relaxed(0x1, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL); + /* + * Before any transactions involving PHY, ensure PHY knows + * that it's analog rail is powered ON. + */ + mb(); + + if (hibern8_exit_after_pwr_collapse) { + /* + * Give atleast 1us delay after restoring PHY analog + * power. + */ + usleep_range(1, 2); + writel_relaxed(0x0A, phy->mmio + + QSERDES_COM_SYSCLK_EN_SEL_TXBAND); + writel_relaxed(0x08, phy->mmio + + QSERDES_COM_SYSCLK_EN_SEL_TXBAND); + /* + * Make sure workaround is deactivated before proceeding + * with normal PHY operations. + */ + mb(); + } + } else { + if (hibern8_exit_after_pwr_collapse) { + writel_relaxed(0x0A, phy->mmio + + QSERDES_COM_SYSCLK_EN_SEL_TXBAND); + writel_relaxed(0x02, phy->mmio + + QSERDES_COM_SYSCLK_EN_SEL_TXBAND); + /* + * Make sure that above workaround is activated before + * PHY analog power collapse. + */ + mb(); + } + + writel_relaxed(0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL); + /* + * ensure that PHY knows its PHY analog rail is going + * to be powered down + */ + mb(); + } +} + +static +void ufs_qcom_phy_qmp_20nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val) +{ + writel_relaxed(val & UFS_PHY_TX_LANE_ENABLE_MASK, + phy->mmio + UFS_PHY_TX_LANE_ENABLE); + /* + * ensure that TX_LANE_ENABLE_MASK is written to PHY before it + * continues + */ + mb(); +} + +static inline void ufs_qcom_phy_qmp_20nm_start_serdes(struct ufs_qcom_phy *phy) +{ + u32 tmp; + + tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START); + tmp &= ~MASK_SERDES_START; + tmp |= (1 << OFFSET_SERDES_START); + writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START); + /* + * ensure that UFS_PHY_PHY_START is written to PHY before before it + * continues + */ + mb(); +} + +static int ufs_qcom_phy_qmp_20nm_is_pcs_ready(struct ufs_qcom_phy *phy_common) +{ + int err = 0; + u32 val; + + err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS, + val, (val & MASK_PCS_READY), 10, 1000000); + if (err) + dev_err(phy_common->dev, "%s: poll for pcs failed err = %d\n", + __func__, err); + return err; +} + +struct phy_ops ufs_qcom_phy_qmp_20nm_phy_ops = { + .init = ufs_qcom_phy_qmp_20nm_init, + .exit = ufs_qcom_phy_exit, + .power_on = ufs_qcom_phy_power_on, + .power_off = ufs_qcom_phy_power_off, + .owner = THIS_MODULE, +}; + +struct ufs_qcom_phy_specific_ops phy_20nm_ops = { + .calibrate_phy = ufs_qcom_phy_qmp_20nm_phy_calibrate, + .start_serdes = ufs_qcom_phy_qmp_20nm_start_serdes, + .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_20nm_is_pcs_ready, + .set_tx_lane_enable = ufs_qcom_phy_qmp_20nm_set_tx_lane_enable, + .power_control = ufs_qcom_phy_qmp_20nm_power_control, +}; + +static int ufs_qcom_phy_qmp_20nm_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct phy *generic_phy; + struct ufs_qcom_phy_qmp_20nm *phy; + int err = 0; + + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL); + if (!phy) { + err = -ENOMEM; + goto out; + } + + generic_phy = ufs_qcom_phy_generic_probe(pdev, &phy->common_cfg, + &ufs_qcom_phy_qmp_20nm_phy_ops, &phy_20nm_ops); + + if (!generic_phy) { + dev_err(dev, "%s: ufs_qcom_phy_generic_probe() failed\n", + __func__); + err = -EIO; + goto out; + } + + phy_set_drvdata(generic_phy, phy); + + strlcpy(phy->common_cfg.name, UFS_PHY_NAME, + sizeof(phy->common_cfg.name)); + +out: + return err; +} + +static int ufs_qcom_phy_qmp_20nm_remove(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct phy *generic_phy = to_phy(dev); + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + int err = 0; + + err = ufs_qcom_phy_remove(generic_phy, ufs_qcom_phy); + if (err) + dev_err(dev, "%s: ufs_qcom_phy_remove failed = %d\n", + __func__, err); + + return err; +} + +static const struct of_device_id ufs_qcom_phy_qmp_20nm_of_match[] = { + {.compatible = "qcom,ufs-phy-qmp-20nm"}, + {}, +}; +MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_20nm_of_match); + +static struct platform_driver ufs_qcom_phy_qmp_20nm_driver = { + .probe = ufs_qcom_phy_qmp_20nm_probe, + .remove = ufs_qcom_phy_qmp_20nm_remove, + .driver = { + .of_match_table = ufs_qcom_phy_qmp_20nm_of_match, + .name = "ufs_qcom_phy_qmp_20nm", + .owner = THIS_MODULE, + }, +}; + +module_platform_driver(ufs_qcom_phy_qmp_20nm_driver); + +MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 20nm"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/phy-qcom-ufs-qmp-20nm.h b/drivers/phy/phy-qcom-ufs-qmp-20nm.h new file mode 100644 index 0000000..189e0ed --- /dev/null +++ b/drivers/phy/phy-qcom-ufs-qmp-20nm.h @@ -0,0 +1,216 @@ +/* + * Copyright (c) 2013-2014, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef UFS_QCOM_PHY_QMP_20NM_H_ +#define UFS_QCOM_PHY_QMP_20NM_H_ + +#include <linux/phy/phy-qcom-ufs.h> + +/* QCOM UFS PHY control registers */ + +#define COM_OFF(x) (0x000 + x) +#define PHY_OFF(x) (0xC00 + x) +#define TX_OFF(n, x) (0x400 + (0x400 * n) + x) +#define RX_OFF(n, x) (0x600 + (0x400 * n) + x) + +/* UFS PHY PLL block registers */ +#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x0) +#define QSERDES_COM_PLL_VCOTAIL_EN COM_OFF(0x04) +#define QSERDES_COM_PLL_CNTRL COM_OFF(0x14) +#define QSERDES_COM_PLL_IP_SETI COM_OFF(0x24) +#define QSERDES_COM_CORE_CLK_IN_SYNC_SEL COM_OFF(0x28) +#define QSERDES_COM_PLL_CP_SETI COM_OFF(0x34) +#define QSERDES_COM_PLL_IP_SETP COM_OFF(0x38) +#define QSERDES_COM_PLL_CP_SETP COM_OFF(0x3C) +#define QSERDES_COM_SYSCLK_EN_SEL_TXBAND COM_OFF(0x48) +#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0x4C) +#define QSERDES_COM_RESETSM_CNTRL2 COM_OFF(0x50) +#define QSERDES_COM_PLLLOCK_CMP1 COM_OFF(0x90) +#define QSERDES_COM_PLLLOCK_CMP2 COM_OFF(0x94) +#define QSERDES_COM_PLLLOCK_CMP3 COM_OFF(0x98) +#define QSERDES_COM_PLLLOCK_CMP_EN COM_OFF(0x9C) +#define QSERDES_COM_BGTC COM_OFF(0xA0) +#define QSERDES_COM_DEC_START1 COM_OFF(0xAC) +#define QSERDES_COM_PLL_AMP_OS COM_OFF(0xB0) +#define QSERDES_COM_DIV_FRAC_START1 COM_OFF(0x100) +#define QSERDES_COM_DIV_FRAC_START2 COM_OFF(0x104) +#define QSERDES_COM_DIV_FRAC_START3 COM_OFF(0x108) +#define QSERDES_COM_DEC_START2 COM_OFF(0x10C) +#define QSERDES_COM_PLL_RXTXEPCLK_EN COM_OFF(0x110) +#define QSERDES_COM_PLL_CRCTRL COM_OFF(0x114) +#define QSERDES_COM_PLL_CLKEPDIV COM_OFF(0x118) + +/* TX LANE n (0, 1) registers */ +#define QSERDES_TX_EMP_POST1_LVL(n) TX_OFF(n, 0x08) +#define QSERDES_TX_DRV_LVL(n) TX_OFF(n, 0x0C) +#define QSERDES_TX_LANE_MODE(n) TX_OFF(n, 0x54) + +/* RX LANE n (0, 1) registers */ +#define QSERDES_RX_CDR_CONTROL1(n) RX_OFF(n, 0x0) +#define QSERDES_RX_CDR_CONTROL_HALF(n) RX_OFF(n, 0x8) +#define QSERDES_RX_RX_EQ_GAIN1_LSB(n) RX_OFF(n, 0xA8) +#define QSERDES_RX_RX_EQ_GAIN1_MSB(n) RX_OFF(n, 0xAC) +#define QSERDES_RX_RX_EQ_GAIN2_LSB(n) RX_OFF(n, 0xB0) +#define QSERDES_RX_RX_EQ_GAIN2_MSB(n) RX_OFF(n, 0xB4) +#define QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(n) RX_OFF(n, 0xBC) +#define QSERDES_RX_CDR_CONTROL_QUARTER(n) RX_OFF(n, 0xC) +#define QSERDES_RX_SIGDET_CNTRL(n) RX_OFF(n, 0x100) + +/* UFS PHY registers */ +#define UFS_PHY_PHY_START PHY_OFF(0x00) +#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x4) +#define UFS_PHY_TX_LANE_ENABLE PHY_OFF(0x44) +#define UFS_PHY_PWM_G1_CLK_DIVIDER PHY_OFF(0x08) +#define UFS_PHY_PWM_G2_CLK_DIVIDER PHY_OFF(0x0C) +#define UFS_PHY_PWM_G3_CLK_DIVIDER PHY_OFF(0x10) +#define UFS_PHY_PWM_G4_CLK_DIVIDER PHY_OFF(0x14) +#define UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER PHY_OFF(0x34) +#define UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER PHY_OFF(0x38) +#define UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER PHY_OFF(0x3C) +#define UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER PHY_OFF(0x40) +#define UFS_PHY_OMC_STATUS_RDVAL PHY_OFF(0x68) +#define UFS_PHY_LINE_RESET_TIME PHY_OFF(0x28) +#define UFS_PHY_LINE_RESET_GRANULARITY PHY_OFF(0x2C) +#define UFS_PHY_TSYNC_RSYNC_CNTL PHY_OFF(0x48) +#define UFS_PHY_PLL_CNTL PHY_OFF(0x50) +#define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x54) +#define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x5C) +#define UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL PHY_OFF(0x58) +#define UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL PHY_OFF(0x60) +#define UFS_PHY_CFG_CHANGE_CNT_VAL PHY_OFF(0x64) +#define UFS_PHY_RX_SYNC_WAIT_TIME PHY_OFF(0x6C) +#define UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB4) +#define UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE0) +#define UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB8) +#define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE4) +#define UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xBC) +#define UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xE8) +#define UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY PHY_OFF(0xFC) +#define UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY PHY_OFF(0x100) +#define UFS_PHY_RMMI_ATTR_CTRL PHY_OFF(0x160) +#define UFS_PHY_RMMI_RX_CFGUPDT_L1 (1 << 7) +#define UFS_PHY_RMMI_TX_CFGUPDT_L1 (1 << 6) +#define UFS_PHY_RMMI_CFGWR_L1 (1 << 5) +#define UFS_PHY_RMMI_CFGRD_L1 (1 << 4) +#define UFS_PHY_RMMI_RX_CFGUPDT_L0 (1 << 3) +#define UFS_PHY_RMMI_TX_CFGUPDT_L0 (1 << 2) +#define UFS_PHY_RMMI_CFGWR_L0 (1 << 1) +#define UFS_PHY_RMMI_CFGRD_L0 (1 << 0) +#define UFS_PHY_RMMI_ATTRID PHY_OFF(0x164) +#define UFS_PHY_RMMI_ATTRWRVAL PHY_OFF(0x168) +#define UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS PHY_OFF(0x16C) +#define UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS PHY_OFF(0x170) +#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x174) + +#define UFS_PHY_TX_LANE_ENABLE_MASK 0x3 + +/* + * This structure represents the 20nm specific phy. + * common_cfg MUST remain the first field in this structure + * in case extra fields are added. This way, when calling + * get_ufs_qcom_phy() of generic phy, we can extract the + * common phy structure (struct ufs_qcom_phy) out of it + * regardless of the relevant specific phy. + */ +struct ufs_qcom_phy_qmp_20nm { + struct ufs_qcom_phy common_cfg; +}; + +static struct ufs_qcom_phy_calibration phy_cal_table_rate_A[] = { + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_VCOTAIL_EN, 0xe1), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x1b), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(0), 0x2F), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(0), 0x20), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_EMP_POST1_LVL(1), 0x2F), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_DRV_LVL(1), 0x20), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc), +}; + +static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = { + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xcc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL_TXBAND, 0x08), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x98), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x40), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0x65), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x1e), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x90), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(0), 0xf2), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL1(1), 0xf2), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(0), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_LSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1_MSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_LSB(1), 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2_MSB(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x1b), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x68), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x68), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(1), 0xdc), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2(0), 0xdc), +}; + +#endif diff --git a/drivers/phy/phy-qcom-ufs-qmp-28nm.c b/drivers/phy/phy-qcom-ufs-qmp-28nm.c new file mode 100644 index 0000000..21594e1 --- /dev/null +++ b/drivers/phy/phy-qcom-ufs-qmp-28nm.c @@ -0,0 +1,342 @@ +/* + * Copyright (c) 2013-2014, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/time.h> +#include <linux/clk.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/phy/phy.h> + +#include <linux/phy/phy-qcom-ufs.h> +#include "phy-qcom-ufs-qmp-28nm.h" + +#define UFS_PHY_NAME "ufs_qcom_phy_qmp_28nm" + +static +void ufs_qcom_phy_qmp_28nm_power_control(struct ufs_qcom_phy *phy, bool val) +{ + if (val) { + writel_relaxed(0x1, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL); + /* + * Before any transactions involving PHY, ensure PHY knows + * that it's analog rail is powered ON. This also ensures + * that PHY is out of power collapse before enabling the + * SIGDET. + */ + mb(); + if (phy->quirks & UFS_QCOM_PHY_DIS_SIGDET_BEFORE_PWR_COLLAPSE) { + writel_relaxed(0xC0, + phy->mmio + QSERDES_RX_SIGDET_CNTRL(0)); + writel_relaxed(0xC0, + phy->mmio + QSERDES_RX_SIGDET_CNTRL(1)); + /* + * make sure that SIGDET is enabled before proceeding + * further. + */ + mb(); + } + } else { + if (phy->quirks & + UFS_QCOM_PHY_DIS_SIGDET_BEFORE_PWR_COLLAPSE) { + writel_relaxed(0x0, + phy->mmio + QSERDES_RX_SIGDET_CNTRL(0)); + writel_relaxed(0x0, + phy->mmio + QSERDES_RX_SIGDET_CNTRL(1)); + /* + * Ensure that SIGDET is disabled before PHY power + * collapse + */ + mb(); + } + writel_relaxed(0x0, phy->mmio + UFS_PHY_POWER_DOWN_CONTROL); + /* + * ensure that PHY knows its PHY analog rail is going + * to be powered down + */ + mb(); + } +} + +static +void ufs_qcom_phy_qmp_28nm_advertise_quirks(struct ufs_qcom_phy *phy_common) +{ + phy_common->quirks = UFS_QCOM_PHY_QUIRK_CFG_RESTORE + | UFS_QCOM_PHY_DIS_SIGDET_BEFORE_PWR_COLLAPSE; +} + +static int ufs_qcom_phy_qmp_28nm_init(struct phy *generic_phy) +{ + struct ufs_qcom_phy_qmp_28nm *phy = phy_get_drvdata(generic_phy); + struct ufs_qcom_phy *phy_common = &phy->common_cfg; + int err = 0; + + err = ufs_qcom_phy_init_clks(generic_phy, phy_common); + if (err) { + dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_clks() failed %d\n", + __func__, err); + goto out; + } + + err = ufs_qcom_phy_init_vregulators(generic_phy, phy_common); + if (err) { + dev_err(phy_common->dev, "%s: ufs_qcom_phy_init_vregulators() failed %d\n", + __func__, err); + goto out; + } + + ufs_qcom_phy_qmp_28nm_advertise_quirks(phy_common); + +out: + return err; +} + +static int ufs_qcom_phy_qmp_28nm_calibrate(struct ufs_qcom_phy *ufs_qcom_phy) +{ + struct ufs_qcom_phy_calibration *tbl_A, *tbl_B; + int tbl_size_A, tbl_size_B; + int rate = UFS_QCOM_LIMIT_HS_RATE; + u8 major = ufs_qcom_phy->host_ctrl_rev_major; + u16 minor = ufs_qcom_phy->host_ctrl_rev_minor; + u16 step = ufs_qcom_phy->host_ctrl_rev_step; + int err; + + if ((major == 0x1) && (minor == 0x001) && (step == 0x0000)) { + tbl_size_A = ARRAY_SIZE(phy_cal_table_ctrl_1_1_0_rate_A); + tbl_A = phy_cal_table_ctrl_1_1_0_rate_A; + } else if ((major == 0x1) && (minor == 0x001) && (step == 0x0001)) { + tbl_size_A = ARRAY_SIZE(phy_cal_table_ctrl_1_1_1_rate_A); + tbl_A = phy_cal_table_ctrl_1_1_1_rate_A; + } else { + tbl_size_A = 0; + tbl_A = NULL; + } + + tbl_B = phy_cal_table_rate_B; + tbl_size_B = ARRAY_SIZE(phy_cal_table_rate_B); + + err = ufs_qcom_phy_calibrate(ufs_qcom_phy, tbl_A, tbl_size_A, + tbl_B, tbl_size_B, rate); + if (err) + dev_err(ufs_qcom_phy->dev, "%s: ufs_qcom_phy_calibrate() failed %d\n", + __func__, err); + + return err; +} + +static +u32 ufs_qcom_phy_qmp_28nm_read_attr(struct ufs_qcom_phy *phy_common, u32 attr) + +{ + u32 l0, l1; + + writel_relaxed(attr, phy_common->mmio + UFS_PHY_RMMI_ATTRID); + /* Read attribute value for both lanes */ + writel_relaxed((UFS_PHY_RMMI_CFGRD_L0 | UFS_PHY_RMMI_CFGRD_L1), + phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL); + + l0 = readl_relaxed(phy_common->mmio + UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS); + l1 = readl_relaxed(phy_common->mmio + UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS); + /* Both lanes should have the same value for same attribute type */ + if (unlikely(l0 != l1)) + dev_warn(phy_common->dev, "%s: attr 0x%x values are not same for Lane-0 and Lane-1, l0=0x%x, l1=0x%x", + __func__, attr, l0, l1); + + /* must clear now */ + writel_relaxed(0x00, phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL); + + return l0; +} + +static void +ufs_qcom_phy_qmp_28nm_write_attr(struct ufs_qcom_phy *phy_common, + u32 attr, u32 val) +{ + writel_relaxed(attr, phy_common->mmio + UFS_PHY_RMMI_ATTRID); + writel_relaxed(val, phy_common->mmio + UFS_PHY_RMMI_ATTRWRVAL); + /* update attribute for both lanes */ + writel_relaxed((UFS_PHY_RMMI_CFGWR_L0 | UFS_PHY_RMMI_CFGWR_L1), + phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL); + if (is_mphy_tx_attr(attr)) + writel_relaxed((UFS_PHY_RMMI_TX_CFGUPDT_L0 | + UFS_PHY_RMMI_TX_CFGUPDT_L1), + phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL); + else + writel_relaxed((UFS_PHY_RMMI_RX_CFGUPDT_L0 | + UFS_PHY_RMMI_RX_CFGUPDT_L1), + phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL); + + writel_relaxed(0x00, phy_common->mmio + UFS_PHY_RMMI_ATTR_CTRL); +} + +static +void ufs_qcom_phy_qmp_28nm_save_configuration(struct ufs_qcom_phy *phy_common) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(cached_phy_regs); i++) + cached_phy_regs[i].cfg_value = + readl_relaxed(phy_common->mmio + + cached_phy_regs[i].reg_offset); + + for (i = 0; i < ARRAY_SIZE(cached_phy_attr); i++) + cached_phy_attr[i].value = + ufs_qcom_phy_qmp_28nm_read_attr(phy_common, + cached_phy_attr[i].att); +} + +static void +ufs_qcom_phy_qmp_28nm_restore_configuration(struct ufs_qcom_phy *phy_common) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(cached_phy_attr); i++) + ufs_qcom_phy_qmp_28nm_write_attr(phy_common, + cached_phy_attr[i].att, cached_phy_attr[i].value); +} + +static +void ufs_qcom_phy_qmp_28nm_set_tx_lane_enable(struct ufs_qcom_phy *phy, u32 val) +{ + writel_relaxed(val & UFS_PHY_TX_LANE_ENABLE_MASK, + phy->mmio + UFS_PHY_TX_LANE_ENABLE); + /* + * ensure that TX_LANE_ENABLE_MASK is written to PHY before it + * continues + */ + mb(); +} + +static inline void ufs_qcom_phy_qmp_28nm_start_serdes(struct ufs_qcom_phy *phy) +{ + u32 tmp; + + tmp = readl_relaxed(phy->mmio + UFS_PHY_PHY_START); + tmp &= ~MASK_SERDES_START; + tmp |= (1 << OFFSET_SERDES_START); + writel_relaxed(tmp, phy->mmio + UFS_PHY_PHY_START); + /* + * ensure that UFS_PHY_PHY_START is written to PHY before before it + * continues + */ + mb(); +} + +static int ufs_qcom_phy_qmp_28nm_is_pcs_ready(struct ufs_qcom_phy *phy_common) +{ + int err = 0; + u32 val; + + err = readl_poll_timeout(phy_common->mmio + UFS_PHY_PCS_READY_STATUS, + val, (val & MASK_PCS_READY), 10, 1000000); + if (err) + dev_err(phy_common->dev, "%s: phy init failed, %d\n", + __func__, err); + + return err; +} + +struct phy_ops ufs_qcom_phy_qmp_28nm_phy_ops = { + .init = ufs_qcom_phy_qmp_28nm_init, + .exit = ufs_qcom_phy_exit, + .power_on = ufs_qcom_phy_power_on, + .power_off = ufs_qcom_phy_power_off, + .owner = THIS_MODULE, +}; + +struct ufs_qcom_phy_specific_ops phy_28nm_ops = { + .calibrate_phy = ufs_qcom_phy_qmp_28nm_calibrate, + .start_serdes = ufs_qcom_phy_qmp_28nm_start_serdes, + .save_configuration = ufs_qcom_phy_qmp_28nm_save_configuration, + .restore_configuration = ufs_qcom_phy_qmp_28nm_restore_configuration, + .is_physical_coding_sublayer_ready = ufs_qcom_phy_qmp_28nm_is_pcs_ready, + .set_tx_lane_enable = ufs_qcom_phy_qmp_28nm_set_tx_lane_enable, + .power_control = ufs_qcom_phy_qmp_28nm_power_control, +}; + +static int ufs_qcom_phy_qmp_28nm_probe(struct platform_device *pdev) +{ + struct ufs_qcom_phy_qmp_28nm *phy; + struct device *dev = &pdev->dev; + int err = 0; + struct phy *generic_phy; + + phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL); + if (!phy) { + err = -ENOMEM; + dev_err(dev, "%s: failed to allocate phy\n", __func__); + goto out; + } + + phy->common_cfg.cached_regs = + (struct ufs_qcom_phy_calibration *)cached_phy_regs; + phy->common_cfg.cached_regs_table_size = + ARRAY_SIZE(cached_phy_regs); + + generic_phy = ufs_qcom_phy_generic_probe(pdev, &phy->common_cfg, + &ufs_qcom_phy_qmp_28nm_phy_ops, &phy_28nm_ops); + + if (!generic_phy) { + dev_err(dev, "%s: ufs_qcom_phy_generic_probe() failed\n", + __func__); + err = -EIO; + goto out; + } + + phy_set_drvdata(generic_phy, phy); + + strlcpy(phy->common_cfg.name, UFS_PHY_NAME, + sizeof(phy->common_cfg.name)); + +out: + return err; +} + +static int ufs_qcom_phy_qmp_28nm_remove(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct phy *generic_phy = to_phy(dev); + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + int err = 0; + + err = ufs_qcom_phy_remove(generic_phy, ufs_qcom_phy); + if (err) + dev_err(dev, "%s: ufs_qcom_phy_remove failed = %d\n", + __func__, err); + + return err; +} + +static const struct of_device_id ufs_qcom_phy_qmp_28nm_of_match[] = { + {.compatible = "qcom,ufs-phy-qmp-28nm"}, + {}, +}; +MODULE_DEVICE_TABLE(of, ufs_qcom_phy_qmp_28nm_of_match); + +static struct platform_driver ufs_qcom_phy_qmp_28nm_driver = { + .probe = ufs_qcom_phy_qmp_28nm_probe, + .remove = ufs_qcom_phy_qmp_28nm_remove, + .driver = { + .of_match_table = ufs_qcom_phy_qmp_28nm_of_match, + .name = "ufs_qcom_phy_qmp_28nm", + .owner = THIS_MODULE, + }, +}; + +module_platform_driver(ufs_qcom_phy_qmp_28nm_driver); + +MODULE_DESCRIPTION("Universal Flash Storage (UFS) QCOM PHY QMP 28nm"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/phy/phy-qcom-ufs-qmp-28nm.h b/drivers/phy/phy-qcom-ufs-qmp-28nm.h new file mode 100644 index 0000000..b406d99 --- /dev/null +++ b/drivers/phy/phy-qcom-ufs-qmp-28nm.h @@ -0,0 +1,738 @@ +/* + * Copyright (c) 2013-2014, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef UFS_QCOM_PHY_QMP_28NM_H_ +#define UFS_QCOM_PHY_QMP_28NM_H_ + +#include <linux/phy/phy-qcom-ufs.h> + +/* QCOM UFS PHY control registers */ + +#define COM_OFF(x) (0x000 + x) +#define PHY_OFF(x) (0x700 + x) +#define TX_OFF(n, x) (0x100 + (0x400 * n) + x) +#define RX_OFF(n, x) (0x200 + (0x400 * n) + x) + +/* UFS PHY PLL block registers */ +#define QSERDES_COM_SYS_CLK_CTRL COM_OFF(0x00) +#define QSERDES_COM_PLL_VCOTAIL_EN COM_OFF(0x04) +#define QSERDES_COM_CMN_MODE COM_OFF(0x08) +#define QSERDES_COM_IE_TRIM COM_OFF(0x0C) +#define QSERDES_COM_IP_TRIM COM_OFF(0x10) +#define QSERDES_COM_PLL_CNTRL COM_OFF(0x14) +#define QSERDES_COM_PLL_IP_SETI COM_OFF(0x18) +#define QSERDES_COM_CORE_CLK_IN_SYNC_SEL COM_OFF(0x1C) +#define QSERDES_COM_BIAS_EN_CLKBUFLR_EN COM_OFF(0x20) +#define QSERDES_COM_PLL_CP_SETI COM_OFF(0x24) +#define QSERDES_COM_PLL_IP_SETP COM_OFF(0x28) +#define QSERDES_COM_PLL_CP_SETP COM_OFF(0x2C) +#define QSERDES_COM_ATB_SEL1 COM_OFF(0x30) +#define QSERDES_COM_ATB_SEL2 COM_OFF(0x34) +#define QSERDES_COM_SYSCLK_EN_SEL COM_OFF(0x38) +#define QSERDES_COM_RES_CODE_TXBAND COM_OFF(0x3C) +#define QSERDES_COM_RESETSM_CNTRL COM_OFF(0x40) +#define QSERDES_COM_PLLLOCK_CMP1 COM_OFF(0x44) +#define QSERDES_COM_PLLLOCK_CMP2 COM_OFF(0x48) +#define QSERDES_COM_PLLLOCK_CMP3 COM_OFF(0x4C) +#define QSERDES_COM_PLLLOCK_CMP_EN COM_OFF(0x50) +#define QSERDES_COM_RES_TRIM_OFFSET COM_OFF(0x54) +#define QSERDES_COM_BGTC COM_OFF(0x58) +#define QSERDES_COM_PLL_TEST_UPDN_RESTRIMSTEP COM_OFF(0x5C) +#define QSERDES_COM_PLL_VCO_TUNE COM_OFF(0x60) +#define QSERDES_COM_DEC_START1 COM_OFF(0x64) +#define QSERDES_COM_PLL_AMP_OS COM_OFF(0x68) +#define QSERDES_COM_SSC_EN_CENTER COM_OFF(0x6C) +#define QSERDES_COM_SSC_ADJ_PER1 COM_OFF(0x70) +#define QSERDES_COM_SSC_ADJ_PER2 COM_OFF(0x74) +#define QSERDES_COM_SSC_PER1 COM_OFF(0x78) +#define QSERDES_COM_SSC_PER2 COM_OFF(0x7C) +#define QSERDES_COM_SSC_STEP_SIZE1 COM_OFF(0x80) +#define QSERDES_COM_SSC_STEP_SIZE2 COM_OFF(0x84) +#define QSERDES_COM_RES_TRIM_SEARCH COM_OFF(0x88) +#define QSERDES_COM_RES_TRIM_FREEZE COM_OFF(0x8C) +#define QSERDES_COM_RES_TRIM_EN_VCOCALDONE COM_OFF(0x90) +#define QSERDES_COM_FAUX_EN COM_OFF(0x94) +#define QSERDES_COM_DIV_FRAC_START1 COM_OFF(0x98) +#define QSERDES_COM_DIV_FRAC_START2 COM_OFF(0x9C) +#define QSERDES_COM_DIV_FRAC_START3 COM_OFF(0xA0) +#define QSERDES_COM_DEC_START2 COM_OFF(0xA4) +#define QSERDES_COM_PLL_RXTXEPCLK_EN COM_OFF(0xA8) +#define QSERDES_COM_PLL_CRCTRL COM_OFF(0xAC) +#define QSERDES_COM_PLL_CLKEPDIV COM_OFF(0xB0) +#define QSERDES_COM_PLL_FREQUPDATE COM_OFF(0xB4) +#define QSERDES_COM_PLL_VCO_HIGH COM_OFF(0xB8) +#define QSERDES_COM_RESET_SM COM_OFF(0xBC) + +/* UFS PHY registers */ +#define UFS_PHY_PHY_START PHY_OFF(0x00) +#define UFS_PHY_POWER_DOWN_CONTROL PHY_OFF(0x04) +#define UFS_PHY_PWM_G1_CLK_DIVIDER PHY_OFF(0x08) +#define UFS_PHY_PWM_G2_CLK_DIVIDER PHY_OFF(0x0C) +#define UFS_PHY_PWM_G3_CLK_DIVIDER PHY_OFF(0x10) +#define UFS_PHY_PWM_G4_CLK_DIVIDER PHY_OFF(0x14) +#define UFS_PHY_TIMER_100US_SYSCLK_STEPS_MSB PHY_OFF(0x18) +#define UFS_PHY_TIMER_100US_SYSCLK_STEPS_LSB PHY_OFF(0x1C) +#define UFS_PHY_TIMER_20US_CORECLK_STEPS_MSB PHY_OFF(0x20) +#define UFS_PHY_TIMER_20US_CORECLK_STEPS_LSB PHY_OFF(0x24) +#define UFS_PHY_LINE_RESET_TIME PHY_OFF(0x28) +#define UFS_PHY_LINE_RESET_GRANULARITY PHY_OFF(0x2C) +#define UFS_PHY_CONTROLSYM_ONE_HOT_DISABLE PHY_OFF(0x30) +#define UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER PHY_OFF(0x34) +#define UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER PHY_OFF(0x38) +#define UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER PHY_OFF(0x3C) +#define UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER PHY_OFF(0x40) +#define UFS_PHY_TX_LANE_ENABLE PHY_OFF(0x44) +#define UFS_PHY_TSYNC_RSYNC_CNTL PHY_OFF(0x48) +#define UFS_PHY_RETIME_BUFFER_EN PHY_OFF(0x4C) +#define UFS_PHY_PLL_CNTL PHY_OFF(0x50) +#define UFS_PHY_TX_LARGE_AMP_DRV_LVL PHY_OFF(0x54) +#define UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL PHY_OFF(0x58) +#define UFS_PHY_TX_SMALL_AMP_DRV_LVL PHY_OFF(0x5C) +#define UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL PHY_OFF(0x60) +#define UFS_PHY_CFG_CHANGE_CNT_VAL PHY_OFF(0x64) +#define UFS_PHY_OMC_STATUS_RDVAL PHY_OFF(0x68) +#define UFS_PHY_RX_SYNC_WAIT_TIME PHY_OFF(0x6C) +#define UFS_PHY_L0_BIST_CTRL PHY_OFF(0x70) +#define UFS_PHY_L1_BIST_CTRL PHY_OFF(0x74) +#define UFS_PHY_BIST_PRBS_POLY0 PHY_OFF(0x78) +#define UFS_PHY_BIST_PRBS_POLY1 PHY_OFF(0x7C) +#define UFS_PHY_BIST_PRBS_SEED0 PHY_OFF(0x80) +#define UFS_PHY_BIST_PRBS_SEED1 PHY_OFF(0x84) +#define UFS_PHY_BIST_FIXED_PAT_CTRL PHY_OFF(0x88) +#define UFS_PHY_BIST_FIXED_PAT0_DATA PHY_OFF(0x8C) +#define UFS_PHY_BIST_FIXED_PAT1_DATA PHY_OFF(0x90) +#define UFS_PHY_BIST_FIXED_PAT2_DATA PHY_OFF(0x94) +#define UFS_PHY_BIST_FIXED_PAT3_DATA PHY_OFF(0x98) +#define UFS_PHY_TX_HSGEAR_CAPABILITY PHY_OFF(0x9C) +#define UFS_PHY_TX_PWMGEAR_CAPABILITY PHY_OFF(0xA0) +#define UFS_PHY_TX_AMPLITUDE_CAPABILITY PHY_OFF(0xA4) +#define UFS_PHY_TX_EXTERNALSYNC_CAPABILITY PHY_OFF(0xA8) +#define UFS_PHY_TX_HS_UNTERMINATED_LINE_DRIVE_CAPABILITY PHY_OFF(0xAC) +#define UFS_PHY_TX_LS_TERMINATED_LINE_DRIVE_CAPABILITY PHY_OFF(0xB0) +#define UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB4) +#define UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xB8) +#define UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xBC) +#define UFS_PHY_TX_REF_CLOCK_SHARED_CAPABILITY PHY_OFF(0xC0) +#define UFS_PHY_TX_PHY_MAJORMINOR_RELEASE_CAPABILITY PHY_OFF(0xC4) +#define UFS_PHY_TX_PHY_EDITORIAL_RELEASE_CAPABILITY PHY_OFF(0xC8) +#define UFS_PHY_TX_HIBERN8TIME_CAPABILITY PHY_OFF(0xCC) +#define UFS_PHY_RX_HSGEAR_CAPABILITY PHY_OFF(0xD0) +#define UFS_PHY_RX_PWMGEAR_CAPABILITY PHY_OFF(0xD4) +#define UFS_PHY_RX_HS_UNTERMINATED_CAPABILITY PHY_OFF(0xD8) +#define UFS_PHY_RX_LS_TERMINATED_CAPABILITY PHY_OFF(0xDC) +#define UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE0) +#define UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY PHY_OFF(0xE4) +#define UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY PHY_OFF(0xE8) +#define UFS_PHY_RX_REF_CLOCK_SHARED_CAPABILITY PHY_OFF(0xEC) +#define UFS_PHY_RX_HS_G1_SYNC_LENGTH_CAPABILITY PHY_OFF(0xF0) +#define UFS_PHY_RX_HS_G1_PREPARE_LENGTH_CAPABILITY PHY_OFF(0xF4) +#define UFS_PHY_RX_LS_PREPARE_LENGTH_CAPABILITY PHY_OFF(0xF8) +#define UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY PHY_OFF(0xFC) +#define UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY PHY_OFF(0x100) +#define UFS_PHY_RX_PHY_MAJORMINOR_RELEASE_CAPABILITY PHY_OFF(0x104) +#define UFS_PHY_RX_PHY_EDITORIAL_RELEASE_CAPABILITY PHY_OFF(0x108) +#define UFS_PHY_RX_HIBERN8TIME_CAPABILITY PHY_OFF(0x10C) +#define UFS_PHY_RX_HS_G2_SYNC_LENGTH_CAPABILITY PHY_OFF(0x110) +#define UFS_PHY_RX_HS_G3_SYNC_LENGTH_CAPABILITY PHY_OFF(0x114) +#define UFS_PHY_RX_HS_G2_PREPARE_LENGTH_CAPABILITY PHY_OFF(0x118) +#define UFS_PHY_RX_HS_G3_PREPARE_LENGTH_CAPABILITY PHY_OFF(0x11C) +#define UFS_PHY_DEBUG_BUS_SEL PHY_OFF(0x120) +#define UFS_PHY_DEBUG_BUS_0_STATUS_CHK PHY_OFF(0x124) +#define UFS_PHY_DEBUG_BUS_1_STATUS_CHK PHY_OFF(0x128) +#define UFS_PHY_DEBUG_BUS_2_STATUS_CHK PHY_OFF(0x12C) +#define UFS_PHY_DEBUG_BUS_3_STATUS_CHK PHY_OFF(0x130) +#define UFS_PHY_PCS_READY_STATUS PHY_OFF(0x134) +#define UFS_PHY_L0_BIST_CHK_ERR_CNT_L_STATUS PHY_OFF(0x138) +#define UFS_PHY_L0_BIST_CHK_ERR_CNT_H_STATUS PHY_OFF(0x13C) +#define UFS_PHY_L1_BIST_CHK_ERR_CNT_L_STATUS PHY_OFF(0x140) +#define UFS_PHY_L1_BIST_CHK_ERR_CNT_H_STATUS PHY_OFF(0x144) +#define UFS_PHY_L0_BIST_CHK_STATUS PHY_OFF(0x148) +#define UFS_PHY_L1_BIST_CHK_STATUS PHY_OFF(0x14C) +#define UFS_PHY_DEBUG_BUS_0_STATUS PHY_OFF(0x150) +#define UFS_PHY_DEBUG_BUS_1_STATUS PHY_OFF(0x154) +#define UFS_PHY_DEBUG_BUS_2_STATUS PHY_OFF(0x158) +#define UFS_PHY_DEBUG_BUS_3_STATUS PHY_OFF(0x15C) +#define UFS_PHY_RMMI_ATTR_CTRL PHY_OFF(0x16C) +#define UFS_PHY_RMMI_RX_CFGUPDT_L1 (1 << 7) +#define UFS_PHY_RMMI_TX_CFGUPDT_L1 (1 << 6) +#define UFS_PHY_RMMI_CFGWR_L1 (1 << 5) +#define UFS_PHY_RMMI_CFGRD_L1 (1 << 4) +#define UFS_PHY_RMMI_RX_CFGUPDT_L0 (1 << 3) +#define UFS_PHY_RMMI_TX_CFGUPDT_L0 (1 << 2) +#define UFS_PHY_RMMI_CFGWR_L0 (1 << 1) +#define UFS_PHY_RMMI_CFGRD_L0 (1 << 0) +#define UFS_PHY_RMMI_ATTRID PHY_OFF(0x170) +#define UFS_PHY_RMMI_ATTRWRVAL PHY_OFF(0x174) +#define UFS_PHY_RMMI_ATTRRDVAL_L0_STATUS PHY_OFF(0x178) +#define UFS_PHY_RMMI_ATTRRDVAL_L1_STATUS PHY_OFF(0x17C) + +/* TX LANE n (0, 1) registers */ +#define QSERDES_TX_BIST_MODE_LANENO(n) TX_OFF(n, 0x00) +#define QSERDES_TX_CLKBUF_ENABLE(n) TX_OFF(n, 0x04) +#define QSERDES_TX_TX_EMP_POST1_LVL(n) TX_OFF(n, 0x08) +#define QSERDES_TX_TX_DRV_LVL(n) TX_OFF(n, 0x0C) +#define QSERDES_TX_RESET_TSYNC_EN(n) TX_OFF(n, 0x10) +#define QSERDES_TX_LPB_EN(n) TX_OFF(n, 0x14) +#define QSERDES_TX_RES_CODE(n) TX_OFF(n, 0x18) +#define QSERDES_TX_PERL_LENGTH1(n) TX_OFF(n, 0x1C) +#define QSERDES_TX_PERL_LENGTH2(n) TX_OFF(n, 0x20) +#define QSERDES_TX_SERDES_BYP_EN_OUT(n) TX_OFF(n, 0x24) +#define QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(n) TX_OFF(n, 0x28) +#define QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(n) TX_OFF(n, 0x2C) +#define QSERDES_TX_BIST_PATTERN1(n) TX_OFF(n, 0x30) +#define QSERDES_TX_BIST_PATTERN2(n) TX_OFF(n, 0x34) +#define QSERDES_TX_BIST_PATTERN3(n) TX_OFF(n, 0x38) +#define QSERDES_TX_BIST_PATTERN4(n) TX_OFF(n, 0x3C) +#define QSERDES_TX_BIST_PATTERN5(n) TX_OFF(n, 0x40) +#define QSERDES_TX_BIST_PATTERN6(n) TX_OFF(n, 0x44) +#define QSERDES_TX_BIST_PATTERN7(n) TX_OFF(n, 0x48) +#define QSERDES_TX_BIST_PATTERN8(n) TX_OFF(n, 0x4C) +#define QSERDES_TX_LANE_MODE(n) TX_OFF(n, 0x50) +#define QSERDES_TX_ATB_SEL(n) TX_OFF(n, 0x54) +#define QSERDES_TX_REC_DETECT_LVL(n) TX_OFF(n, 0x58) +#define QSERDES_TX_PRBS_SEED1(n) TX_OFF(n, 0x5C) +#define QSERDES_TX_PRBS_SEED2(n) TX_OFF(n, 0x60) +#define QSERDES_TX_PRBS_SEED3(n) TX_OFF(n, 0x64) +#define QSERDES_TX_PRBS_SEED4(n) TX_OFF(n, 0x68) +#define QSERDES_TX_RESET_GEN(n) TX_OFF(n, 0x6C) +#define QSERDES_TX_TRAN_DRVR_EMP_EN(n) TX_OFF(n, 0x70) +#define QSERDES_TX_TX_INTERFACE_MODE(n) TX_OFF(n, 0x74) +#define QSERDES_TX_BIST_STATUS(n) TX_OFF(n, 0x78) +#define QSERDES_TX_BIST_ERROR_COUNT1(n) TX_OFF(n, 0x7C) +#define QSERDES_TX_BIST_ERROR_COUNT2(n) TX_OFF(n, 0x80) + +/* RX LANE n (0, 1) registers */ +#define QSERDES_RX_CDR_CONTROL(n) RX_OFF(n, 0x00) +#define QSERDES_RX_AUX_CONTROL(n) RX_OFF(n, 0x04) +#define QSERDES_RX_AUX_DATA_TCODE(n) RX_OFF(n, 0x08) +#define QSERDES_RX_RCLK_AUXDATA_SEL(n) RX_OFF(n, 0x0C) +#define QSERDES_RX_EQ_CONTROL(n) RX_OFF(n, 0x10) +#define QSERDES_RX_RX_EQ_GAIN2(n) RX_OFF(n, 0x14) +#define QSERDES_RX_AC_JTAG_INIT(n) RX_OFF(n, 0x18) +#define QSERDES_RX_AC_JTAG_LVL_EN(n) RX_OFF(n, 0x1C) +#define QSERDES_RX_AC_JTAG_MODE(n) RX_OFF(n, 0x20) +#define QSERDES_RX_AC_JTAG_RESET(n) RX_OFF(n, 0x24) +#define QSERDES_RX_RX_IQ_RXDET_EN(n) RX_OFF(n, 0x28) +#define QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(n) RX_OFF(n, 0x2C) +#define QSERDES_RX_RX_EQ_GAIN1(n) RX_OFF(n, 0x30) +#define QSERDES_RX_SIGDET_CNTRL(n) RX_OFF(n, 0x34) +#define QSERDES_RX_RX_BAND(n) RX_OFF(n, 0x38) +#define QSERDES_RX_CDR_FREEZE_UP_DN(n) RX_OFF(n, 0x3C) +#define QSERDES_RX_RX_INTERFACE_MODE(n) RX_OFF(n, 0x40) +#define QSERDES_RX_JITTER_GEN_MODE(n) RX_OFF(n, 0x44) +#define QSERDES_RX_BUJ_AMP(n) RX_OFF(n, 0x48) +#define QSERDES_RX_SJ_AMP1(n) RX_OFF(n, 0x4C) +#define QSERDES_RX_SJ_AMP2(n) RX_OFF(n, 0x50) +#define QSERDES_RX_SJ_PER1(n) RX_OFF(n, 0x54) +#define QSERDES_RX_SJ_PER2(n) RX_OFF(n, 0x58) +#define QSERDES_RX_BUJ_STEP_FREQ1(n) RX_OFF(n, 0x5C) +#define QSERDES_RX_BUJ_STEP_FREQ2(n) RX_OFF(n, 0x60) +#define QSERDES_RX_PPM_OFFSET1(n) RX_OFF(n, 0x64) +#define QSERDES_RX_PPM_OFFSET2(n) RX_OFF(n, 0x68) +#define QSERDES_RX_SIGN_PPM_PERIOD1(n) RX_OFF(n, 0x6C) +#define QSERDES_RX_SIGN_PPM_PERIOD2(n) RX_OFF(n, 0x70) +#define QSERDES_RX_SSC_CTRL(n) RX_OFF(n, 0x74) +#define QSERDES_RX_SSC_COUNT1(n) RX_OFF(n, 0x78) +#define QSERDES_RX_SSC_COUNT2(n) RX_OFF(n, 0x7C) +#define QSERDES_RX_PWM_CNTRL1(n) RX_OFF(n, 0x80) +#define QSERDES_RX_PWM_CNTRL2(n) RX_OFF(n, 0x84) +#define QSERDES_RX_PWM_NDIV(n) RX_OFF(n, 0x88) +#define QSERDES_RX_SIGDET_CNTRL2(n) RX_OFF(n, 0x8C) +#define QSERDES_RX_UFS_CNTRL(n) RX_OFF(n, 0x90) +#define QSERDES_RX_CDR_CONTROL3(n) RX_OFF(n, 0x94) +#define QSERDES_RX_CDR_CONTROL_HALF(n) RX_OFF(n, 0x98) +#define QSERDES_RX_CDR_CONTROL_QUARTER(n) RX_OFF(n, 0x9C) +#define QSERDES_RX_CDR_CONTROL_EIGHTH(n) RX_OFF(n, 0xA0) +#define QSERDES_RX_UCDR_FO_GAIN(n) RX_OFF(n, 0xA4) +#define QSERDES_RX_UCDR_SO_GAIN(n) RX_OFF(n, 0xA8) +#define QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(n) RX_OFF(n, 0xAC) +#define QSERDES_RX_UCDR_FO_TO_SO_DELAY(n) RX_OFF(n, 0xB0) +#define QSERDES_RX_PI_CTRL1(n) RX_OFF(n, 0xB4) +#define QSERDES_RX_PI_CTRL2(n) RX_OFF(n, 0xB8) +#define QSERDES_RX_PI_QUAD(n) RX_OFF(n, 0xBC) +#define QSERDES_RX_IDATA1(n) RX_OFF(n, 0xC0) +#define QSERDES_RX_IDATA2(n) RX_OFF(n, 0xC4) +#define QSERDES_RX_AUX_DATA1(n) RX_OFF(n, 0xC8) +#define QSERDES_RX_AUX_DATA2(n) RX_OFF(n, 0xCC) +#define QSERDES_RX_AC_JTAG_OUTP(n) RX_OFF(n, 0xD0) +#define QSERDES_RX_AC_JTAG_OUTN(n) RX_OFF(n, 0xD4) +#define QSERDES_RX_RX_SIGDET_PWMDECSTATUS(n) RX_OFF(n, 0xD8) + +#define UFS_PHY_TX_LANE_ENABLE_MASK 0x3 + +/* + * This structure represents the 28nm specific phy. + * common_cfg MUST remain the first field in this structure + * in case extra fields are added. This way, when calling + * get_ufs_qcom_phy() of generic phy, we can extract the + * common phy structure (struct ufs_qcom_phy) out of it + * regardless of the relevant specific phy. + */ +struct ufs_qcom_phy_qmp_28nm { + struct ufs_qcom_phy common_cfg; +}; + +static struct ufs_qcom_phy_calibration phy_cal_table_ctrl_1_1_0_rate_A[] = { + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0xFF), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x24), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL, 0x08), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYS_CLK_CTRL, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x67), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x13), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_PWM_CNTRL1(0), 0x43), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_PWM_CNTRL1(1), 0x43), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL(0), 0x22), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x2a), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL(1), 0x22), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x2a), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL(0), 0xC0), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL(1), 0xC0), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL2(0), 0x07), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL2(1), 0x07), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G1_CLK_DIVIDER, 0x50), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G2_CLK_DIVIDER, 0x28), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G3_CLK_DIVIDER, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G4_CLK_DIVIDER, 0x08), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER, 0xa8), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER, 0x54), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER, 0x2a), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER, 0x15), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_OMC_STATUS_RDVAL, 0xff), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_LINE_RESET_TIME, 0x1f), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_LINE_RESET_GRANULARITY, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TSYNC_RSYNC_CNTL, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PLL_CNTL, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_DRV_LVL, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_DRV_LVL, 0x1a), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CFG_CHANGE_CNT_VAL, 0x09), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SYNC_WAIT_TIME, 0x30), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY, 0x08), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY, 0x04), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY, 0xc8), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1(0), 0x07), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2(0), 0x07), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1(1), 0x07), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2(1), 0x07), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL3(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL3(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x3f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_TRIM_OFFSET, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BGTC, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_AMP_OS, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_DRV_LVL(0), 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_DRV_LVL(1), 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_BIST_MODE_LANENO(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_BIST_MODE_LANENO(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_EMP_POST1_LVL(0), 0x04), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_EMP_POST1_LVL(1), 0x04), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(0), 0x05), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(1), 0x05), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_100US_SYSCLK_STEPS_MSB, 0x07), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_100US_SYSCLK_STEPS_LSB, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_20US_CORECLK_STEPS_MSB, 0x27), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_20US_CORECLK_STEPS_LSB, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CONTROLSYM_ONE_HOT_DISABLE, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RETIME_BUFFER_EN, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_HSGEAR_CAPABILITY, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_PWMGEAR_CAPABILITY, 0x04), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_AMPLITUDE_CAPABILITY, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_EXTERNALSYNC_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_HS_UNTERMINATED_LINE_DRIVE_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_LS_TERMINATED_LINE_DRIVE_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_REF_CLOCK_SHARED_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_HIBERN8TIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HSGEAR_CAPABILITY, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_PWMGEAR_CAPABILITY, 0x04), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_UNTERMINATED_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_LS_TERMINATED_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_REF_CLOCK_SHARED_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G1_SYNC_LENGTH_CAPABILITY, 0x48), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_HS_G1_PREPARE_LENGTH_CAPABILITY, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_LS_PREPARE_LENGTH_CAPABILITY, 0x09), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HIBERN8TIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G2_SYNC_LENGTH_CAPABILITY, 0x48), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G3_SYNC_LENGTH_CAPABILITY, 0x48), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_HS_G2_PREPARE_LENGTH_CAPABILITY, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_HS_G3_PREPARE_LENGTH_CAPABILITY, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_CLKBUF_ENABLE(0), 0x09), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RESET_TSYNC_EN(0), 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RES_CODE(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_SERDES_BYP_EN_OUT(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_REC_DETECT_LVL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TRAN_DRVR_EMP_EN(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_CONTROL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_DATA_TCODE(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RCLK_AUXDATA_SEL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_EQ_CONTROL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_IQ_RXDET_EN(0), 0x73), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(0), 0x05), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_FREEZE_UP_DN(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UFS_CNTRL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_EIGHTH(0), 0x22), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_GAIN(0), 0x0a), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_GAIN(0), 0x06), + UFS_QCOM_PHY_CAL_ENTRY( + QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(0), 0x35), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_TO_SO_DELAY(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_CLKBUF_ENABLE(1), 0x09), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RESET_TSYNC_EN(1), 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RES_CODE(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_SERDES_BYP_EN_OUT(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_REC_DETECT_LVL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TRAN_DRVR_EMP_EN(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_CONTROL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_DATA_TCODE(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RCLK_AUXDATA_SEL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_EQ_CONTROL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_IQ_RXDET_EN(1), 0x73), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(1), 0x05), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_FREEZE_UP_DN(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UFS_CNTRL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_EIGHTH(1), 0x22), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_GAIN(1), 0x0a), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_GAIN(1), 0x06), + UFS_QCOM_PHY_CAL_ENTRY( + QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(1), 0x35), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_TO_SO_DELAY(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_MODE, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_IE_TRIM, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_IP_TRIM, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORE_CLK_IN_SYNC_SEL, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_TEST_UPDN_RESTRIMSTEP, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_FAUX_EN, 0x00), +}; + +static struct ufs_qcom_phy_calibration phy_cal_table_ctrl_1_1_1_rate_A[] = { + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_POWER_DOWN_CONTROL, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CRCTRL, 0x43), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CNTRL, 0x24), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYSCLK_EN_SEL, 0x08), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_SYS_CLK_CTRL, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x82), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0xff), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x19), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RESETSM_CNTRL, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_RXTXEPCLK_EN, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_PWM_CNTRL1(0), 0x43), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_PWM_CNTRL1(1), 0x43), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL(0), 0x40), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(0), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(0), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL(1), 0x40), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_HALF(1), 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_QUARTER(1), 0x12), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL(0), 0xC0), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL(1), 0xC0), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL2(0), 0x07), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_SIGDET_CNTRL2(1), 0x07), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G1_CLK_DIVIDER, 0x30), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G2_CLK_DIVIDER, 0x18), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G3_CLK_DIVIDER, 0x0c), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PWM_G4_CLK_DIVIDER, 0x06), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER, 0xa8), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER, 0x54), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER, 0x2a), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER, 0x15), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_OMC_STATUS_RDVAL, 0xff), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_LINE_RESET_TIME, 0x1f), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_LINE_RESET_GRANULARITY, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TSYNC_RSYNC_CNTL, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_PLL_CNTL, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_DRV_LVL, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_DRV_LVL, 0x1a), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CFG_CHANGE_CNT_VAL, 0x09), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_SYNC_WAIT_TIME, 0x30), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY, 0x08), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY, 0x04), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY, 0xc8), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1(0), 0x1f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2(0), 0x17), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN1(1), 0x1f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_EQ_GAIN2(1), 0x17), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL3(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL3(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETI, 0x07), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETI, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_IP_SETP, 0x07), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CP_SETP, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_RES_TRIM_OFFSET, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BGTC, 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_AMP_OS, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_DRV_LVL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_DRV_LVL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_BIST_MODE_LANENO(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_BIST_MODE_LANENO(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_EMP_POST1_LVL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TX_EMP_POST1_LVL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(0), 0x05), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_EN(1), 0x05), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_100US_SYSCLK_STEPS_MSB, 0x07), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_100US_SYSCLK_STEPS_LSB, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_20US_CORECLK_STEPS_MSB, 0x27), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TIMER_20US_CORECLK_STEPS_LSB, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_CONTROLSYM_ONE_HOT_DISABLE, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RETIME_BUFFER_EN, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_HSGEAR_CAPABILITY, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_PWMGEAR_CAPABILITY, 0x04), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_AMPLITUDE_CAPABILITY, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_EXTERNALSYNC_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_HS_UNTERMINATED_LINE_DRIVE_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY( + UFS_PHY_TX_LS_TERMINATED_LINE_DRIVE_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_REF_CLOCK_SHARED_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_TX_HIBERN8TIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HSGEAR_CAPABILITY, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_PWMGEAR_CAPABILITY, 0x04), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_UNTERMINATED_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_LS_TERMINATED_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_REF_CLOCK_SHARED_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G1_SYNC_LENGTH_CAPABILITY, 0x48), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G1_PREPARE_LENGTH_CAPABILITY, + 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_LS_PREPARE_LENGTH_CAPABILITY, 0x0a), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HIBERN8TIME_CAPABILITY, 0x01), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G2_SYNC_LENGTH_CAPABILITY, 0x48), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G3_SYNC_LENGTH_CAPABILITY, 0x48), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G2_PREPARE_LENGTH_CAPABILITY, + 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(UFS_PHY_RX_HS_G3_PREPARE_LENGTH_CAPABILITY, + 0x0f), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_CLKBUF_ENABLE(0), 0x09), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RESET_TSYNC_EN(0), 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RES_CODE(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_SERDES_BYP_EN_OUT(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_REC_DETECT_LVL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TRAN_DRVR_EMP_EN(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_CONTROL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_DATA_TCODE(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RCLK_AUXDATA_SEL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_EQ_CONTROL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_IQ_RXDET_EN(0), 0x51), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(0), 0x05), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_FREEZE_UP_DN(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UFS_CNTRL(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_EIGHTH(0), 0x22), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_GAIN(0), 0x0a), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_GAIN(0), 0x06), + UFS_QCOM_PHY_CAL_ENTRY( + QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(0), 0x35), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_TO_SO_DELAY(0), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_CLKBUF_ENABLE(1), 0x09), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RESET_TSYNC_EN(1), 0x01), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_RES_CODE(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_SERDES_BYP_EN_OUT(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_REC_DETECT_LVL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_PARRATE_REC_DETECT_IDLE_EN(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_TRAN_DRVR_EMP_EN(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_CONTROL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_AUX_DATA_TCODE(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RCLK_AUXDATA_SEL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_EQ_CONTROL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_IQ_RXDET_EN(1), 0x51), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_RX_TERM_HIGHZ_CM_AC_COUPLE(1), 0x05), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_FREEZE_UP_DN(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UFS_CNTRL(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_CDR_CONTROL_EIGHTH(1), 0x22), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_GAIN(1), 0x0a), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_SO_GAIN(1), 0x06), + UFS_QCOM_PHY_CAL_ENTRY( + QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE(1), 0x35), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_RX_UCDR_FO_TO_SO_DELAY(1), 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CMN_MODE, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_IE_TRIM, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_IP_TRIM, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_CORE_CLK_IN_SYNC_SEL, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_TEST_UPDN_RESTRIMSTEP, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_FAUX_EN, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(0), 0x08), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_TX_LANE_MODE(1), 0x08), +}; + +static struct ufs_qcom_phy_calibration phy_cal_table_rate_B[] = { + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLL_CLKEPDIV, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START1, 0x98), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DEC_START2, 0x03), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START1, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START2, 0x80), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_DIV_FRAC_START3, 0x10), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP1, 0x65), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP2, 0x1E), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP3, 0x00), + UFS_QCOM_PHY_CAL_ENTRY(QSERDES_COM_PLLLOCK_CMP_EN, 0x03), +}; + +static struct ufs_qcom_phy_calibration cached_phy_regs[] = { + {QSERDES_COM_PLL_CRCTRL}, + {QSERDES_COM_PLL_CNTRL}, + {QSERDES_COM_SYSCLK_EN_SEL}, + {QSERDES_COM_SYS_CLK_CTRL}, + {QSERDES_COM_PLL_CLKEPDIV}, + {QSERDES_COM_DEC_START1}, + {QSERDES_COM_DEC_START2}, + {QSERDES_COM_DIV_FRAC_START1}, + {QSERDES_COM_DIV_FRAC_START2}, + {QSERDES_COM_DIV_FRAC_START3}, + {QSERDES_COM_PLLLOCK_CMP1}, + {QSERDES_COM_PLLLOCK_CMP2}, + {QSERDES_COM_PLLLOCK_CMP3}, + {QSERDES_COM_PLLLOCK_CMP_EN}, + {QSERDES_COM_RESETSM_CNTRL}, + {QSERDES_COM_PLL_RXTXEPCLK_EN}, + {QSERDES_RX_PWM_CNTRL1(0)}, + {QSERDES_RX_PWM_CNTRL1(1)}, + {QSERDES_RX_CDR_CONTROL(0)}, + {QSERDES_RX_CDR_CONTROL_HALF(0)}, + {QSERDES_RX_CDR_CONTROL_QUARTER(0)}, + {QSERDES_RX_CDR_CONTROL(1)}, + {QSERDES_RX_CDR_CONTROL_HALF(1)}, + {QSERDES_RX_CDR_CONTROL_QUARTER(1)}, + {QSERDES_RX_SIGDET_CNTRL(0)}, + {QSERDES_RX_SIGDET_CNTRL(1)}, + {QSERDES_RX_SIGDET_CNTRL2(0)}, + {QSERDES_RX_SIGDET_CNTRL2(1)}, + {QSERDES_RX_RX_EQ_GAIN1(0)}, + {QSERDES_RX_RX_EQ_GAIN2(0)}, + {QSERDES_RX_RX_EQ_GAIN1(1)}, + {QSERDES_RX_RX_EQ_GAIN2(1)}, + {QSERDES_COM_PLL_IP_SETI}, + {QSERDES_COM_PLL_CP_SETI}, + {QSERDES_COM_PLL_IP_SETP}, + {QSERDES_COM_PLL_CP_SETP}, + {UFS_PHY_PWM_G1_CLK_DIVIDER}, + {UFS_PHY_PWM_G2_CLK_DIVIDER}, + {UFS_PHY_PWM_G3_CLK_DIVIDER}, + {UFS_PHY_PWM_G4_CLK_DIVIDER}, + {UFS_PHY_CORECLK_PWM_G1_CLK_DIVIDER}, + {UFS_PHY_CORECLK_PWM_G2_CLK_DIVIDER}, + {UFS_PHY_CORECLK_PWM_G3_CLK_DIVIDER}, + {UFS_PHY_CORECLK_PWM_G4_CLK_DIVIDER}, + {UFS_PHY_OMC_STATUS_RDVAL}, + {UFS_PHY_LINE_RESET_TIME}, + {UFS_PHY_LINE_RESET_GRANULARITY}, + {UFS_PHY_TSYNC_RSYNC_CNTL}, + {UFS_PHY_PLL_CNTL}, + {UFS_PHY_TX_LARGE_AMP_DRV_LVL}, + {UFS_PHY_TX_SMALL_AMP_DRV_LVL}, + {UFS_PHY_TX_LARGE_AMP_POST_EMP_LVL}, + {UFS_PHY_TX_SMALL_AMP_POST_EMP_LVL}, + {UFS_PHY_CFG_CHANGE_CNT_VAL}, + {UFS_PHY_RX_SYNC_WAIT_TIME}, + {UFS_PHY_TX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY}, + {UFS_PHY_RX_MIN_SLEEP_NOCONFIG_TIME_CAPABILITY}, + {UFS_PHY_TX_MIN_STALL_NOCONFIG_TIME_CAPABILITY}, + {UFS_PHY_RX_MIN_STALL_NOCONFIG_TIME_CAPABILITY}, + {UFS_PHY_TX_MIN_SAVE_CONFIG_TIME_CAPABILITY}, + {UFS_PHY_RX_MIN_SAVE_CONFIG_TIME_CAPABILITY}, + {UFS_PHY_RX_PWM_BURST_CLOSURE_LENGTH_CAPABILITY}, + {UFS_PHY_RX_MIN_ACTIVATETIME_CAPABILITY}, + {QSERDES_RX_CDR_CONTROL3(0)}, + {QSERDES_RX_CDR_CONTROL3(1)}, + {QSERDES_COM_RES_TRIM_OFFSET}, + {QSERDES_COM_BGTC}, + {QSERDES_COM_PLL_AMP_OS}, +}; + +static struct ufs_qcom_phy_stored_attributes cached_phy_attr[] = { + {TX_MODE}, + {TX_HSRATE_SERIES}, + {TX_HSGEAR}, + {TX_PWMGEAR}, + {TX_AMPLITUDE}, + {TX_HS_SLEWRATE}, + {TX_SYNC_SOURCE}, + {TX_HS_PREPARE_LENGTH}, + {TX_LS_PREPARE_LENGTH}, + {TX_LCC_ENABLE}, + {TX_PWM_BURST_CLOSURE_EXTENSION}, + {TX_BYPASS_8B10B_ENABLE}, + {TX_DRIVER_POLARITY}, + {TX_HS_UNTERMINATED_LINE_DRIVE_ENABLE}, + {TX_LS_TERMINATED_LINE_DRIVE_ENABLE}, + {TX_LCC_SEQUENCER}, + {TX_MIN_ACTIVATETIME}, + {TX_PWM_G6_G7_SYNC_LENGTH}, + {RX_MODE}, + {RX_HSRATE_SERIES}, + {RX_HSGEAR}, + {RX_PWMGEAR}, + {RX_LS_TERMINATED_ENABLE}, + {RX_HS_UNTERMINATED_ENABLE}, + {RX_ENTER_HIBERN8}, + {RX_BYPASS_8B10B_ENABLE}, + {RX_TERMINATION_FORCE_ENABLE}, +}; + +#endif diff --git a/drivers/phy/phy-qcom-ufs.c b/drivers/phy/phy-qcom-ufs.c new file mode 100644 index 0000000..48af90f --- /dev/null +++ b/drivers/phy/phy-qcom-ufs.c @@ -0,0 +1,661 @@ +/* + * Copyright (c) 2013-2014, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/time.h> +#include <linux/clk.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include <linux/phy/phy-qcom-ufs.h> + +int ufs_qcom_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy, + struct ufs_qcom_phy_calibration *tbl_A, + int tbl_size_A, + struct ufs_qcom_phy_calibration *tbl_B, + int tbl_size_B, int rate) +{ + int i; + int ret = 0; + + if (!tbl_A) { + dev_err(ufs_qcom_phy->dev, "%s: tbl_A is NULL", __func__); + ret = EINVAL; + goto out; + } + + for (i = 0; i < tbl_size_A; i++) + writel_relaxed(tbl_A[i].cfg_value, + ufs_qcom_phy->mmio + tbl_A[i].reg_offset); + + /* + * In case we would like to work in rate B, we need + * to override a registers that were configured in rate A table + * with registers of rate B table. + * table. + */ + if (rate == PA_HS_MODE_B) { + if (!tbl_B) { + dev_err(ufs_qcom_phy->dev, "%s: tbl_B is NULL", + __func__); + ret = EINVAL; + goto out; + } + + for (i = 0; i < tbl_size_B; i++) + writel_relaxed(tbl_B[i].cfg_value, + ufs_qcom_phy->mmio + tbl_B[i].reg_offset); + } + + /* flush buffered writes */ + mb(); + +out: + return ret; +} + +struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev, + struct ufs_qcom_phy *common_cfg, + struct phy_ops *ufs_qcom_phy_gen_ops, + struct ufs_qcom_phy_specific_ops *phy_spec_ops) +{ + int err; + struct device *dev = &pdev->dev; + struct phy *generic_phy = NULL; + struct phy_provider *phy_provider; + + err = ufs_qcom_phy_base_init(pdev, common_cfg); + if (err) { + dev_err(dev, "%s: phy base init failed %d\n", __func__, err); + goto out; + } + + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + if (IS_ERR(phy_provider)) { + err = PTR_ERR(phy_provider); + dev_err(dev, "%s: failed to register phy %d\n", __func__, err); + goto out; + } + + generic_phy = devm_phy_create(dev, NULL, ufs_qcom_phy_gen_ops, NULL); + if (IS_ERR(generic_phy)) { + err = PTR_ERR(generic_phy); + dev_err(dev, "%s: failed to create phy %d\n", __func__, err); + goto out; + } + + common_cfg->phy_spec_ops = phy_spec_ops; + common_cfg->dev = dev; + +out: + return generic_phy; +} + +/* + * This assumes the embedded phy structure inside generic_phy is of type + * struct ufs_qcom_phy. In order to function properly it's crucial + * to keep the embedded struct "struct ufs_qcom_phy common_cfg" + * as the first inside generic_phy. + */ +struct ufs_qcom_phy *get_ufs_qcom_phy(struct phy *generic_phy) +{ + return (struct ufs_qcom_phy *)phy_get_drvdata(generic_phy); +} + +int ufs_qcom_phy_base_init(struct platform_device *pdev, + struct ufs_qcom_phy *phy_common) +{ + struct device *dev = &pdev->dev; + struct resource *res; + int err = 0; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(dev, "%s: platform_get_resource() failed. returned NULL\n", + __func__); + err = -ENOMEM; + goto out; + } + + phy_common->mmio = devm_ioremap_resource(dev, res); + if (IS_ERR(phy_common->mmio)) { + err = PTR_ERR(phy_common->mmio); + dev_err(dev, "ioremap resource failed %d\n", err); + } + +out: + return err; +} + +int ufs_qcom_phy_clk_get(struct phy *phy, + const char *name, struct clk **clk_out) +{ + struct clk *clk; + int err = 0; + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy); + struct device *dev = ufs_qcom_phy->dev; + + clk = devm_clk_get(dev, name); + if (IS_ERR(clk)) { + err = PTR_ERR(clk); + dev_err(dev, "failed to get %s err %d", name, err); + } else { + *clk_out = clk; + } + + return err; +} + +int +ufs_qcom_phy_init_clks(struct phy *generic_phy, + struct ufs_qcom_phy *phy_common) +{ + int err; + + err = ufs_qcom_phy_clk_get(generic_phy, "tx_iface_clk", + &phy_common->tx_iface_clk); + if (err) + goto out; + + err = ufs_qcom_phy_clk_get(generic_phy, "rx_iface_clk", + &phy_common->rx_iface_clk); + if (err) + goto out; + + err = ufs_qcom_phy_clk_get(generic_phy, "ref_clk_src", + &phy_common->ref_clk_src); + if (err) + goto out; + + err = ufs_qcom_phy_clk_get(generic_phy, "ref_clk_parent", + &phy_common->ref_clk_parent); + if (err) + goto out; + + err = ufs_qcom_phy_clk_get(generic_phy, "ref_clk", + &phy_common->ref_clk); + +out: + return err; +} + +int +ufs_qcom_phy_init_vregulators(struct phy *generic_phy, + struct ufs_qcom_phy *phy_common) +{ + int err; + + err = ufs_qcom_phy_init_vreg(generic_phy, &phy_common->vdda_pll, + "vdda-pll"); + if (err) + goto out; + + err = ufs_qcom_phy_init_vreg(generic_phy, &phy_common->vdda_phy, + "vdda-phy"); +out: + return err; +} + +int ufs_qcom_phy_init_vreg(struct phy *phy, + struct ufs_qcom_phy_vreg *vreg, const char *name) +{ + int err = 0; + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy); + struct device *dev = ufs_qcom_phy->dev; + + char prop_name[MAX_PROP_NAME]; + + vreg->name = kstrdup(name, GFP_KERNEL); + if (!vreg->name) { + err = -ENOMEM; + goto out; + } + + vreg->reg = devm_regulator_get(dev, name); + if (IS_ERR(vreg->reg)) { + err = PTR_ERR(vreg->reg); + dev_err(dev, "failed to get %s, %d\n", name, err); + goto out; + } + + if (dev->of_node) { + snprintf(prop_name, MAX_PROP_NAME, "%s-max-microamp", name); + err = of_property_read_u32(dev->of_node, + prop_name, &vreg->max_uA); + if (err && err != -EINVAL) { + dev_err(dev, "%s: failed to read %s\n", + __func__, prop_name); + goto out; + } else if (err == -EINVAL || !vreg->max_uA) { + if (regulator_count_voltages(vreg->reg) > 0) { + dev_err(dev, "%s: %s is mandatory\n", + __func__, prop_name); + goto out; + } + err = 0; + } + } + + if (!strcmp(name, "vdda-pll")) { + vreg->max_uV = VDDA_PLL_MAX_UV; + vreg->min_uV = VDDA_PLL_MIN_UV; + } else if (!strcmp(name, "vdda-phy")) { + vreg->max_uV = VDDA_PHY_MAX_UV; + vreg->min_uV = VDDA_PHY_MIN_UV; + } + +out: + if (err) + kfree(vreg->name); + return err; +} + +int ufs_qcom_phy_cfg_vreg(struct phy *phy, + struct ufs_qcom_phy_vreg *vreg, bool on) +{ + int ret = 0; + struct regulator *reg = vreg->reg; + const char *name = vreg->name; + int min_uV; + int uA_load; + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy); + struct device *dev = ufs_qcom_phy->dev; + + BUG_ON(!vreg); + + if (regulator_count_voltages(reg) > 0) { + min_uV = on ? vreg->min_uV : 0; + ret = regulator_set_voltage(reg, min_uV, vreg->max_uV); + if (ret) { + dev_err(dev, "%s: %s set voltage failed, err=%d\n", + __func__, name, ret); + goto out; + } + uA_load = on ? vreg->max_uA : 0; + ret = regulator_set_optimum_mode(reg, uA_load); + if (ret >= 0) { + /* + * regulator_set_optimum_mode() returns new regulator + * mode upon success. + */ + ret = 0; + } else { + dev_err(dev, "%s: %s set optimum mode(uA_load=%d) failed, err=%d\n", + __func__, name, uA_load, ret); + goto out; + } + } +out: + return ret; +} + +int ufs_qcom_phy_enable_vreg(struct phy *phy, + struct ufs_qcom_phy_vreg *vreg) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy); + struct device *dev = ufs_qcom_phy->dev; + int ret = 0; + + if (!vreg || vreg->enabled) + goto out; + + ret = ufs_qcom_phy_cfg_vreg(phy, vreg, true); + if (ret) { + dev_err(dev, "%s: ufs_qcom_phy_cfg_vreg() failed, err=%d\n", + __func__, ret); + goto out; + } + + ret = regulator_enable(vreg->reg); + if (ret) { + dev_err(dev, "%s: enable failed, err=%d\n", + __func__, ret); + goto out; + } + + vreg->enabled = true; +out: + return ret; +} + +int ufs_qcom_phy_enable_ref_clk(struct phy *generic_phy) +{ + int ret = 0; + struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy); + + if (phy->is_ref_clk_enabled) + goto out; + + /* + * reference clock is propagated in a daisy-chained manner from + * source to phy, so ungate them at each stage. + */ + ret = clk_prepare_enable(phy->ref_clk_src); + if (ret) { + dev_err(phy->dev, "%s: ref_clk_src enable failed %d\n", + __func__, ret); + goto out; + } + + ret = clk_prepare_enable(phy->ref_clk_parent); + if (ret) { + dev_err(phy->dev, "%s: ref_clk_parent enable failed %d\n", + __func__, ret); + goto out_disable_src; + } + + ret = clk_prepare_enable(phy->ref_clk); + if (ret) { + dev_err(phy->dev, "%s: ref_clk enable failed %d\n", + __func__, ret); + goto out_disable_parent; + } + + phy->is_ref_clk_enabled = true; + goto out; + +out_disable_parent: + clk_disable_unprepare(phy->ref_clk_parent); +out_disable_src: + clk_disable_unprepare(phy->ref_clk_src); +out: + return ret; +} + +int ufs_qcom_phy_disable_vreg(struct phy *phy, + struct ufs_qcom_phy_vreg *vreg) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy); + struct device *dev = ufs_qcom_phy->dev; + int ret = 0; + + if (!vreg || !vreg->enabled) + goto out; + + ret = regulator_disable(vreg->reg); + + if (!ret) { + /* ignore errors on applying disable config */ + ufs_qcom_phy_cfg_vreg(phy, vreg, false); + vreg->enabled = false; + } else { + dev_err(dev, "%s: %s disable failed, err=%d\n", + __func__, vreg->name, ret); + } +out: + return ret; +} + +void ufs_qcom_phy_disable_ref_clk(struct phy *generic_phy) +{ + struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy); + + if (phy->is_ref_clk_enabled) { + clk_disable_unprepare(phy->ref_clk); + clk_disable_unprepare(phy->ref_clk_parent); + clk_disable_unprepare(phy->ref_clk_src); + phy->is_ref_clk_enabled = false; + } +} + +void ufs_qcom_phy_restore_swi_regs(struct phy *generic_phy) +{ + int i; + struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy); + + for (i = 0; i < phy->cached_regs_table_size; i++) { + struct ufs_qcom_phy_calibration *table = + (struct ufs_qcom_phy_calibration *)phy->cached_regs; + writel_relaxed(table[i].cfg_value, phy->mmio + + table[i].reg_offset); + } + + /* flush buffered writes */ + mb(); +} + +/* Turn ON M-PHY RMMI interface clocks */ +int ufs_qcom_phy_enable_iface_clk(struct phy *generic_phy) +{ + struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy); + int ret = 0; + + if (phy->is_iface_clk_enabled) + goto out; + + ret = clk_prepare_enable(phy->tx_iface_clk); + if (ret) { + dev_err(phy->dev, "%s: tx_iface_clk enable failed %d\n", + __func__, ret); + goto out; + } + ret = clk_prepare_enable(phy->rx_iface_clk); + if (ret) { + clk_disable_unprepare(phy->tx_iface_clk); + dev_err(phy->dev, "%s: rx_iface_clk enable failed %d. disabling also tx_iface_clk\n", + __func__, ret); + goto out; + } + phy->is_iface_clk_enabled = true; + +out: + return ret; +} + +/* Turn OFF M-PHY RMMI interface clocks */ +void ufs_qcom_phy_disable_iface_clk(struct phy *generic_phy) +{ + struct ufs_qcom_phy *phy = get_ufs_qcom_phy(generic_phy); + + if (phy->is_iface_clk_enabled) { + clk_disable_unprepare(phy->tx_iface_clk); + clk_disable_unprepare(phy->rx_iface_clk); + phy->is_iface_clk_enabled = false; + } +} + +int ufs_qcom_phy_is_cfg_restore_quirk_enabled(struct phy *phy) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(phy); + + return ufs_qcom_phy->quirks & UFS_QCOM_PHY_QUIRK_CFG_RESTORE; +} + +int ufs_qcom_phy_start_serdes(struct phy *generic_phy) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + int ret = 0; + + if (!ufs_qcom_phy->phy_spec_ops->start_serdes) { + dev_err(ufs_qcom_phy->dev, "%s: start_serdes() callback is not supported\n", + __func__); + ret = -ENOTSUPP; + } else { + ufs_qcom_phy->phy_spec_ops->start_serdes(ufs_qcom_phy); + } + + return ret; +} + +int ufs_qcom_phy_set_tx_lane_enable(struct phy *generic_phy, u32 tx_lanes) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + int ret = 0; + + if (!ufs_qcom_phy->phy_spec_ops->set_tx_lane_enable) { + dev_err(ufs_qcom_phy->dev, "%s: set_tx_lane_enable() callback is not supported\n", + __func__); + ret = -ENOTSUPP; + } else { + ufs_qcom_phy->phy_spec_ops->set_tx_lane_enable(ufs_qcom_phy, + tx_lanes); + } + + return ret; +} + +void ufs_qcom_phy_save_controller_version(struct phy *generic_phy, + u8 major, u16 minor, u16 step) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + + ufs_qcom_phy->host_ctrl_rev_major = major; + ufs_qcom_phy->host_ctrl_rev_minor = minor; + ufs_qcom_phy->host_ctrl_rev_step = step; +} + +int ufs_qcom_phy_calibrate_phy(struct phy *generic_phy) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + int ret = 0; + + if (!ufs_qcom_phy->phy_spec_ops->calibrate_phy) { + dev_err(ufs_qcom_phy->dev, "%s: calibrate_phy() callback is not supported\n", + __func__); + ret = -ENOTSUPP; + } else { + ret = ufs_qcom_phy->phy_spec_ops-> + calibrate_phy(ufs_qcom_phy); + if (ret) + dev_err(ufs_qcom_phy->dev, "%s: calibrate_phy() failed %d\n", + __func__, ret); + } + + return ret; +} + +int ufs_qcom_phy_remove(struct phy *generic_phy, + struct ufs_qcom_phy *ufs_qcom_phy) +{ + phy_power_off(generic_phy); + + kfree(ufs_qcom_phy->vdda_pll.name); + kfree(ufs_qcom_phy->vdda_phy.name); + + return 0; +} + +int ufs_qcom_phy_exit(struct phy *generic_phy) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + + if (ufs_qcom_phy->is_powered_on) + phy_power_off(generic_phy); + + return 0; +} + +int ufs_qcom_phy_is_pcs_ready(struct phy *generic_phy) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + + if (!ufs_qcom_phy->phy_spec_ops->is_physical_coding_sublayer_ready) { + dev_err(ufs_qcom_phy->dev, "%s: is_physical_coding_sublayer_ready() callback is not supported\n", + __func__); + return -ENOTSUPP; + } + + return ufs_qcom_phy->phy_spec_ops-> + is_physical_coding_sublayer_ready(ufs_qcom_phy); +} + +int ufs_qcom_phy_save_configuration(struct phy *generic_phy) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + int ret = 0; + + if (!ufs_qcom_phy->phy_spec_ops->save_configuration) { + dev_err(ufs_qcom_phy->dev, "%s: save_configuration() callback is not supported\n", + __func__); + ret = -ENOTSUPP; + } else { + ufs_qcom_phy->phy_spec_ops->save_configuration(ufs_qcom_phy); + } + + return ret; +} + +int ufs_qcom_phy_restore_configuration(struct phy *generic_phy) +{ + struct ufs_qcom_phy *ufs_qcom_phy = get_ufs_qcom_phy(generic_phy); + int ret = 0; + + if (!ufs_qcom_phy->phy_spec_ops->restore_configuration) { + dev_err(ufs_qcom_phy->dev, "%s: restore_configuration() callback is not supported\n", + __func__); + ret = -ENOTSUPP; + } else { + ufs_qcom_phy->phy_spec_ops->restore_configuration(ufs_qcom_phy); + } + + return ret; +} + +int ufs_qcom_phy_power_on(struct phy *generic_phy) +{ + struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); + struct device *dev = phy_common->dev; + int err; + + err = ufs_qcom_phy_enable_vreg(generic_phy, &phy_common->vdda_phy); + if (err) { + dev_err(dev, "%s enable vdda_phy failed, err=%d\n", + __func__, err); + goto out; + } + + phy_common->phy_spec_ops->power_control(phy_common, true); + + /* vdda_pll also enables ref clock LDOs so enable it first */ + err = ufs_qcom_phy_enable_vreg(generic_phy, &phy_common->vdda_pll); + if (err) { + dev_err(dev, "%s enable vdda_pll failed, err=%d\n", + __func__, err); + goto out_disable_phy; + } + + err = ufs_qcom_phy_enable_ref_clk(generic_phy); + if (err) { + dev_err(dev, "%s enable phy ref clock failed, err=%d\n", + __func__, err); + goto out_disable_pll; + } + + phy_common->is_powered_on = true; + goto out; + +out_disable_pll: + ufs_qcom_phy_disable_vreg(generic_phy, &phy_common->vdda_pll); +out_disable_phy: + ufs_qcom_phy_disable_vreg(generic_phy, &phy_common->vdda_phy); +out: + return err; +} + +int ufs_qcom_phy_power_off(struct phy *generic_phy) +{ + struct ufs_qcom_phy *phy_common = get_ufs_qcom_phy(generic_phy); + + phy_common->phy_spec_ops->power_control(phy_common, false); + + ufs_qcom_phy_disable_ref_clk(generic_phy); + + ufs_qcom_phy_disable_vreg(generic_phy, &phy_common->vdda_pll); + ufs_qcom_phy_disable_vreg(generic_phy, &phy_common->vdda_phy); + phy_common->is_powered_on = false; + + return 0; +} diff --git a/drivers/scsi/ufs/Kconfig b/drivers/scsi/ufs/Kconfig index 6e07b2a..b7e426e 100644 --- a/drivers/scsi/ufs/Kconfig +++ b/drivers/scsi/ufs/Kconfig @@ -70,3 +70,15 @@ config SCSI_UFSHCD_PLATFORM If you have a controller with this interface, say Y or M here. If unsure, say N. + +config SCSI_UFS_QCOM + bool "QCOM specific hooks to UFS controller platform driver" + depends on SCSI_UFSHCD_PLATFORM && ARCH_MSM + help + This selects the QCOM specific additions to UFSHCD platform driver. + UFS host on QCOM needs some vendor specific configuration before + accessing the hardware which includes PHY configuration and vendor + specific registers. + + Select this if you have UFS controller on QCOM chipset. + If unsure, say N. \ No newline at end of file diff --git a/drivers/scsi/ufs/Makefile b/drivers/scsi/ufs/Makefile index 1e5bd48..8303bcc 100644 --- a/drivers/scsi/ufs/Makefile +++ b/drivers/scsi/ufs/Makefile @@ -1,4 +1,5 @@ # UFSHCD makefile +obj-$(CONFIG_SCSI_UFS_QCOM) += ufs-qcom.o obj-$(CONFIG_SCSI_UFSHCD) += ufshcd.o obj-$(CONFIG_SCSI_UFSHCD_PCI) += ufshcd-pci.o obj-$(CONFIG_SCSI_UFSHCD_PLATFORM) += ufshcd-pltfrm.o diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c new file mode 100644 index 0000000..47e55e8 --- /dev/null +++ b/drivers/scsi/ufs/ufs-qcom.c @@ -0,0 +1,866 @@ +/* + * Copyright (c) 2013-2014, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/time.h> +#include <linux/clk.h> +#include <linux/of.h> +#include <linux/platform_device.h> + +#include <linux/scsi/ufs/ufshcd.h> +#include <linux/scsi/ufs/ufs-qcom.h> +#include <linux/phy/phy-qcom-ufs.h> +#include "ufshci.h" + +static int ufs_qcom_get_connected_tx_lanes(struct ufs_hba *hba, u32 *tx_lanes) +{ + int err = 0; + + err = ufshcd_dme_get(hba, + UIC_ARG_MIB(PA_CONNECTEDTXDATALANES), tx_lanes); + if (err) + dev_err(hba->dev, "%s: couldn't read PA_CONNECTEDTXDATALANES %d\n", + __func__, err); + + return err; +} + +static int ufs_qcom_host_clk_get(struct device *dev, + const char *name, struct clk **clk_out) +{ + struct clk *clk; + int err = 0; + + clk = devm_clk_get(dev, name); + if (IS_ERR(clk)) { + err = PTR_ERR(clk); + dev_err(dev, "%s: failed to get %s err %d", + __func__, name, err); + } else { + *clk_out = clk; + } + + return err; +} + +static int ufs_qcom_host_clk_enable(struct device *dev, + const char *name, struct clk *clk) +{ + int err = 0; + + err = clk_prepare_enable(clk); + if (err) + dev_err(dev, "%s: %s enable failed %d\n", __func__, name, err); + + return err; +} + +static void ufs_qcom_disable_lane_clks(struct ufs_qcom_host *host) +{ + if (!host->is_lane_clks_enabled) + return; + + clk_disable_unprepare(host->tx_l1_sync_clk); + clk_disable_unprepare(host->tx_l0_sync_clk); + clk_disable_unprepare(host->rx_l1_sync_clk); + clk_disable_unprepare(host->rx_l0_sync_clk); + + host->is_lane_clks_enabled = false; +} + +static int ufs_qcom_enable_lane_clks(struct ufs_qcom_host *host) +{ + int err = 0; + struct device *dev = host->hba->dev; + + if (host->is_lane_clks_enabled) + return 0; + + err = ufs_qcom_host_clk_enable(dev, + "rx_lane0_sync_clk", host->rx_l0_sync_clk); + if (err) + goto out; + + err = ufs_qcom_host_clk_enable(dev, + "rx_lane1_sync_clk", host->rx_l1_sync_clk); + if (err) + goto disable_rx_l0; + + err = ufs_qcom_host_clk_enable(dev, + "tx_lane0_sync_clk", host->tx_l0_sync_clk); + if (err) + goto disable_rx_l1; + + err = ufs_qcom_host_clk_enable(dev, + "tx_lane1_sync_clk", host->tx_l1_sync_clk); + if (err) + goto disable_tx_l0; + + host->is_lane_clks_enabled = true; + goto out; + +disable_tx_l0: + clk_disable_unprepare(host->tx_l0_sync_clk); +disable_rx_l1: + clk_disable_unprepare(host->rx_l1_sync_clk); +disable_rx_l0: + clk_disable_unprepare(host->rx_l0_sync_clk); +out: + return err; +} + +static int ufs_qcom_init_lane_clks(struct ufs_qcom_host *host) +{ + int err = 0; + struct device *dev = host->hba->dev; + + err = ufs_qcom_host_clk_get(dev, + "rx_lane0_sync_clk", &host->rx_l0_sync_clk); + if (err) + goto out; + + err = ufs_qcom_host_clk_get(dev, + "rx_lane1_sync_clk", &host->rx_l1_sync_clk); + if (err) + goto out; + + err = ufs_qcom_host_clk_get(dev, + "tx_lane0_sync_clk", &host->tx_l0_sync_clk); + if (err) + goto out; + + err = ufs_qcom_host_clk_get(dev, + "tx_lane1_sync_clk", &host->tx_l1_sync_clk); +out: + return err; +} + +static int ufs_qcom_link_startup_post_change(struct ufs_hba *hba) +{ + struct ufs_qcom_host *host = hba->priv; + struct phy *phy = host->generic_phy; + u32 tx_lanes; + int err = 0; + + err = ufs_qcom_get_connected_tx_lanes(hba, &tx_lanes); + if (err) + goto out; + + err = ufs_qcom_phy_set_tx_lane_enable(phy, tx_lanes); + if (err) + dev_err(hba->dev, "%s: ufs_qcom_phy_set_tx_lane_enable failed\n", + __func__); + +out: + return err; +} + +static int ufs_qcom_check_hibern8(struct ufs_hba *hba) +{ + int err; + u32 tx_fsm_val = 0; + unsigned long timeout = jiffies + msecs_to_jiffies(HBRN8_POLL_TOUT_MS); + + do { + err = ufshcd_dme_get(hba, + UIC_ARG_MIB(MPHY_TX_FSM_STATE), &tx_fsm_val); + if (err || tx_fsm_val == TX_FSM_HIBERN8) + break; + + /* sleep for max. 200us */ + usleep_range(100, 200); + } while (time_before(jiffies, timeout)); + + /* + * we might have scheduled out for long during polling so + * check the state again. + */ + if (time_after(jiffies, timeout)) + err = ufshcd_dme_get(hba, + UIC_ARG_MIB(MPHY_TX_FSM_STATE), &tx_fsm_val); + + if (err) { + dev_err(hba->dev, "%s: unable to get TX_FSM_STATE, err %d\n", + __func__, err); + } else if (tx_fsm_val != TX_FSM_HIBERN8) { + err = tx_fsm_val; + dev_err(hba->dev, "%s: invalid TX_FSM_STATE = %d\n", + __func__, err); + } + + return err; +} + +static int ufs_qcom_power_up_sequence(struct ufs_hba *hba) +{ + struct ufs_qcom_host *host = hba->priv; + struct phy *phy = host->generic_phy; + int ret = 0; + u8 major; + u16 minor, step; + + /* Assert PHY reset and apply PHY calibration values */ + ufs_qcom_assert_reset(hba); + /* provide 1ms delay to let the reset pulse propagate */ + usleep_range(1000, 1100); + + ufs_qcom_get_controller_revision(hba, &major, &minor, &step); + ufs_qcom_phy_save_controller_version(phy, major, minor, step); + ret = ufs_qcom_phy_calibrate_phy(phy); + if (ret) { + dev_err(hba->dev, "%s: ufs_qcom_phy_calibrate_phy() failed, ret = %d\n", + __func__, ret); + goto out; + } + + /* De-assert PHY reset and start serdes */ + ufs_qcom_deassert_reset(hba); + + /* + * after reset deassertion, phy will need all ref clocks, + * voltage, current to settle down before starting serdes. + */ + usleep_range(1000, 1100); + ret = ufs_qcom_phy_start_serdes(phy); + if (ret) { + dev_err(hba->dev, "%s: ufs_qcom_phy_start_serdes() failed, ret = %d\n", + __func__, ret); + goto out; + } + + ret = ufs_qcom_phy_is_pcs_ready(phy); + if (ret) + dev_err(hba->dev, "%s: is_physical_coding_sublayer_ready() failed, ret = %d\n", + __func__, ret); + +out: + return ret; +} + +static int ufs_qcom_hce_enable_notify(struct ufs_hba *hba, bool status) +{ + struct ufs_qcom_host *host = hba->priv; + int err = 0; + + switch (status) { + case PRE_CHANGE: + ufs_qcom_power_up_sequence(hba); + /* + * The PHY PLL output is the source of tx/rx lane symbol + * clocks, hence, enable the lane clocks only after PHY + * is initialized. + */ + err = ufs_qcom_enable_lane_clks(host); + break; + case POST_CHANGE: + /* check if UFS PHY moved from DISABLED to HIBERN8 */ + err = ufs_qcom_check_hibern8(hba); + break; + default: + dev_err(hba->dev, "%s: invalid status %d\n", __func__, status); + err = -EINVAL; + break; + } + return err; +} + +/** + * Returns non-zero for success (which rate of core_clk) and 0 + * in case of a failure + */ +static unsigned long +ufs_qcom_cfg_timers(struct ufs_hba *hba, u32 gear, u32 hs, u32 rate) +{ + struct ufs_clk_info *clki; + u32 core_clk_period_in_ns; + u32 tx_clk_cycles_per_us = 0; + unsigned long core_clk_rate = 0; + u32 core_clk_cycles_per_us = 0; + + static u32 pwm_fr_table[][2] = { + {UFS_PWM_G1, 0x1}, + {UFS_PWM_G2, 0x1}, + {UFS_PWM_G3, 0x1}, + {UFS_PWM_G4, 0x1}, + }; + + static u32 hs_fr_table_rA[][2] = { + {UFS_HS_G1, 0x1F}, + {UFS_HS_G2, 0x3e}, + }; + + static u32 hs_fr_table_rB[][2] = { + {UFS_HS_G1, 0x24}, + {UFS_HS_G2, 0x49}, + }; + + if (gear == 0) { + dev_err(hba->dev, "%s: invalid gear = %d\n", __func__, gear); + goto out_error; + } + + list_for_each_entry(clki, &hba->clk_list_head, list) { + if (!strcmp(clki->name, "core_clk")) + core_clk_rate = clk_get_rate(clki->clk); + } + + /* If frequency is smaller than 1MHz, set to 1MHz */ + if (core_clk_rate < DEFAULT_CLK_RATE_HZ) + core_clk_rate = DEFAULT_CLK_RATE_HZ; + + core_clk_cycles_per_us = core_clk_rate / USEC_PER_SEC; + ufshcd_writel(hba, core_clk_cycles_per_us, REG_UFS_SYS1CLK_1US); + + core_clk_period_in_ns = NSEC_PER_SEC / core_clk_rate; + core_clk_period_in_ns <<= OFFSET_CLK_NS_REG; + core_clk_period_in_ns &= MASK_CLK_NS_REG; + + switch (hs) { + case FASTAUTO_MODE: + case FAST_MODE: + if (rate == PA_HS_MODE_A) { + if (gear > ARRAY_SIZE(hs_fr_table_rA)) { + dev_err(hba->dev, + "%s: index %d exceeds table size %zu\n", + __func__, gear, + ARRAY_SIZE(hs_fr_table_rA)); + goto out_error; + } + tx_clk_cycles_per_us = hs_fr_table_rA[gear-1][1]; + } else if (rate == PA_HS_MODE_B) { + if (gear > ARRAY_SIZE(hs_fr_table_rB)) { + dev_err(hba->dev, + "%s: index %d exceeds table size %zu\n", + __func__, gear, + ARRAY_SIZE(hs_fr_table_rB)); + goto out_error; + } + tx_clk_cycles_per_us = hs_fr_table_rB[gear-1][1]; + } else { + dev_err(hba->dev, "%s: invalid rate = %d\n", + __func__, rate); + goto out_error; + } + break; + case SLOWAUTO_MODE: + case SLOW_MODE: + if (gear > ARRAY_SIZE(pwm_fr_table)) { + dev_err(hba->dev, + "%s: index %d exceeds table size %zu\n", + __func__, gear, + ARRAY_SIZE(pwm_fr_table)); + goto out_error; + } + tx_clk_cycles_per_us = pwm_fr_table[gear-1][1]; + break; + case UNCHANGED: + default: + dev_err(hba->dev, "%s: invalid mode = %d\n", __func__, hs); + goto out_error; + } + + /* this register 2 fields shall be written at once */ + ufshcd_writel(hba, core_clk_period_in_ns | tx_clk_cycles_per_us, + REG_UFS_TX_SYMBOL_CLK_NS_US); + goto out; + +out_error: + core_clk_rate = 0; +out: + return core_clk_rate; +} + +static int ufs_qcom_link_startup_notify(struct ufs_hba *hba, bool status) +{ + unsigned long core_clk_rate = 0; + u32 core_clk_cycles_per_100ms; + + switch (status) { + case PRE_CHANGE: + core_clk_rate = ufs_qcom_cfg_timers(hba, UFS_PWM_G1, + SLOWAUTO_MODE, 0); + if (!core_clk_rate) { + dev_err(hba->dev, "%s: ufs_qcom_cfg_timers() failed\n", + __func__); + return -EINVAL; + } + core_clk_cycles_per_100ms = + (core_clk_rate / MSEC_PER_SEC) * 100; + ufshcd_writel(hba, core_clk_cycles_per_100ms, + REG_UFS_PA_LINK_STARTUP_TIMER); + break; + case POST_CHANGE: + ufs_qcom_link_startup_post_change(hba); + break; + default: + break; + } + + return 0; +} + +static int ufs_qcom_suspend(struct ufs_hba *hba, enum ufs_pm_op pm_op) +{ + struct ufs_qcom_host *host = hba->priv; + struct phy *phy = host->generic_phy; + int ret = 0; + + if (ufs_qcom_is_link_off(hba)) { + /* + * Disable the tx/rx lane symbol clocks before PHY is + * powered down as the PLL source should be disabled + * after downstream clocks are disabled. + */ + ufs_qcom_disable_lane_clks(host); + phy_power_off(phy); + + goto out; + } + + /* + * If UniPro link is not active, PHY ref_clk, main PHY analog power + * rail and low noise analog power rail for PLL can be switched off. + */ + if (!ufs_qcom_is_link_active(hba)) { + if (ufs_qcom_phy_is_cfg_restore_quirk_enabled(phy) && + ufs_qcom_is_link_hibern8(hba)) { + ret = ufs_qcom_phy_save_configuration(phy); + if (ret) + dev_err(hba->dev, "%s: failed ufs_qcom_phy_save_configuration %d\n", + __func__, ret); + } + phy_power_off(phy); + } + +out: + return ret; +} + +static bool ufs_qcom_is_phy_config_restore_required(struct ufs_hba *hba) +{ + struct ufs_qcom_host *host = hba->priv; + struct phy *phy = host->generic_phy; + + return ufs_qcom_phy_is_cfg_restore_quirk_enabled(phy) + && ufshcd_is_link_hibern8(hba) + && hba->is_sys_suspended; +} + +static int ufs_qcom_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op) +{ + struct ufs_qcom_host *host = hba->priv; + struct phy *phy = host->generic_phy; + int err; + + if (ufs_qcom_is_phy_config_restore_required(hba)) { + ufs_qcom_assert_reset(hba); + /* provide 1ms delay to let the reset pulse propagate */ + usleep_range(1000, 1100); + } + + err = phy_power_on(phy); + if (err) { + dev_err(hba->dev, "%s: failed enabling regs, err = %d\n", + __func__, err); + goto out; + } + + if (ufs_qcom_is_phy_config_restore_required(hba)) { + ufs_qcom_phy_restore_swi_regs(phy); + + /* De-assert PHY reset and start serdes */ + ufs_qcom_deassert_reset(hba); + + /* + * after reset deassertion, phy will need all ref clocks, + * voltage, current to settle down before starting serdes. + */ + usleep_range(1000, 1100); + + err = ufs_qcom_phy_start_serdes(phy); + if (err) { + dev_err(hba->dev, "%s: ufs_qcom_phy_start_serdes() failed, err = %d\n", + __func__, err); + goto out; + } + + err = ufs_qcom_phy_restore_configuration(phy); + if (err) { + dev_err(hba->dev, "%s: ufs_qcom_phy_restore_configuration() failed, err = %d\n", + __func__, err); + goto out; + } + + err = ufs_qcom_phy_is_pcs_ready(phy); + if (err) { + dev_err(hba->dev, "%s: is_physical_coding_sublayer_ready() failed, err = %d\n", + __func__, err); + goto out; + } + } + + hba->is_sys_suspended = false; +out: + return err; +} + +struct ufs_qcom_dev_params { + u32 pwm_rx_gear; /* pwm rx gear to work in */ + u32 pwm_tx_gear; /* pwm tx gear to work in */ + u32 hs_rx_gear; /* hs rx gear to work in */ + u32 hs_tx_gear; /* hs tx gear to work in */ + u32 rx_lanes; /* number of rx lanes */ + u32 tx_lanes; /* number of tx lanes */ + u32 rx_pwr_pwm; /* rx pwm working pwr */ + u32 tx_pwr_pwm; /* tx pwm working pwr */ + u32 rx_pwr_hs; /* rx hs working pwr */ + u32 tx_pwr_hs; /* tx hs working pwr */ + u32 hs_rate; /* rate A/B to work in HS */ + u32 desired_working_mode; +}; + +static int ufs_qcom_get_pwr_dev_param(struct ufs_qcom_dev_params *qcom_param, + struct ufs_pa_layer_attr *dev_max, + struct ufs_pa_layer_attr *agreed_pwr) +{ + int min_qcom_gear; + int min_dev_gear; + bool is_dev_sup_hs = false; + bool is_qcom_max_hs = false; + + if (dev_max->pwr_rx == FAST_MODE) + is_dev_sup_hs = true; + + if (qcom_param->desired_working_mode == FAST) { + is_qcom_max_hs = true; + min_qcom_gear = min_t(u32, qcom_param->hs_rx_gear, + qcom_param->hs_tx_gear); + } else { + min_qcom_gear = min_t(u32, qcom_param->pwm_rx_gear, + qcom_param->pwm_tx_gear); + } + + /* + * device doesn't support HS but qcom_param->desired_working_mode is + * HS, thus device and qcom_param don't agree + */ + if (!is_dev_sup_hs && is_qcom_max_hs) { + pr_err("%s: failed to agree on power mode (device doesn't support HS but requested power is HS)\n", + __func__); + return -ENOTSUPP; + } else if (is_dev_sup_hs && is_qcom_max_hs) { + /* + * since device supports HS, it supports FAST_MODE. + * since qcom_param->desired_working_mode is also HS + * then final decision (FAST/FASTAUTO) is done according + * to qcom_params as it is the restricting factor + */ + agreed_pwr->pwr_rx = agreed_pwr->pwr_tx = + qcom_param->rx_pwr_hs; + } else { + /* + * here qcom_param->desired_working_mode is PWM. + * it doesn't matter whether device supports HS or PWM, + * in both cases qcom_param->desired_working_mode will + * determine the mode + */ + agreed_pwr->pwr_rx = agreed_pwr->pwr_tx = + qcom_param->rx_pwr_pwm; + } + + /* + * we would like tx to work in the minimum number of lanes + * between device capability and vendor preferences. + * the same decision will be made for rx + */ + agreed_pwr->lane_tx = min_t(u32, dev_max->lane_tx, + qcom_param->tx_lanes); + agreed_pwr->lane_rx = min_t(u32, dev_max->lane_rx, + qcom_param->rx_lanes); + + /* device maximum gear is the minimum between device rx and tx gears */ + min_dev_gear = min_t(u32, dev_max->gear_rx, dev_max->gear_tx); + + /* + * if both device capabilities and vendor pre-defined preferences are + * both HS or both PWM then set the minimum gear to be the chosen + * working gear. + * if one is PWM and one is HS then the one that is PWM get to decide + * what is the gear, as it is the one that also decided previously what + * pwr the device will be configured to. + */ + if ((is_dev_sup_hs && is_qcom_max_hs) || + (!is_dev_sup_hs && !is_qcom_max_hs)) + agreed_pwr->gear_rx = agreed_pwr->gear_tx = + min_t(u32, min_dev_gear, min_qcom_gear); + else if (!is_dev_sup_hs) + agreed_pwr->gear_rx = agreed_pwr->gear_tx = min_dev_gear; + else + agreed_pwr->gear_rx = agreed_pwr->gear_tx = min_qcom_gear; + + agreed_pwr->hs_rate = qcom_param->hs_rate; + return 0; +} + +static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba, + bool status, + struct ufs_pa_layer_attr *dev_max_params, + struct ufs_pa_layer_attr *dev_req_params) +{ + u32 val; + struct ufs_qcom_host *host = hba->priv; + struct phy *phy = host->generic_phy; + struct ufs_qcom_dev_params ufs_qcom_cap; + int ret = 0; + int res = 0; + + if (!dev_req_params) { + pr_err("%s: incoming dev_req_params is NULL\n", __func__); + ret = -EINVAL; + goto out; + } + + switch (status) { + case PRE_CHANGE: + ufs_qcom_cap.tx_lanes = UFS_QCOM_LIMIT_NUM_LANES_TX; + ufs_qcom_cap.rx_lanes = UFS_QCOM_LIMIT_NUM_LANES_RX; + ufs_qcom_cap.hs_rx_gear = UFS_QCOM_LIMIT_HSGEAR_RX; + ufs_qcom_cap.hs_tx_gear = UFS_QCOM_LIMIT_HSGEAR_TX; + ufs_qcom_cap.pwm_rx_gear = UFS_QCOM_LIMIT_PWMGEAR_RX; + ufs_qcom_cap.pwm_tx_gear = UFS_QCOM_LIMIT_PWMGEAR_TX; + ufs_qcom_cap.rx_pwr_pwm = UFS_QCOM_LIMIT_RX_PWR_PWM; + ufs_qcom_cap.tx_pwr_pwm = UFS_QCOM_LIMIT_TX_PWR_PWM; + ufs_qcom_cap.rx_pwr_hs = UFS_QCOM_LIMIT_RX_PWR_HS; + ufs_qcom_cap.tx_pwr_hs = UFS_QCOM_LIMIT_TX_PWR_HS; + ufs_qcom_cap.hs_rate = UFS_QCOM_LIMIT_HS_RATE; + ufs_qcom_cap.desired_working_mode = + UFS_QCOM_LIMIT_DESIRED_MODE; + + ret = ufs_qcom_get_pwr_dev_param(&ufs_qcom_cap, + dev_max_params, + dev_req_params); + if (ret) { + pr_err("%s: failed to determine capabilities\n", + __func__); + goto out; + } + + break; + case POST_CHANGE: + if (!ufs_qcom_cfg_timers(hba, dev_req_params->gear_rx, + dev_req_params->pwr_rx, + dev_req_params->hs_rate)) { + dev_err(hba->dev, "%s: ufs_qcom_cfg_timers() failed\n", + __func__); + /* + * we return error code at the end of the routine, + * but continue to configure UFS_PHY_TX_LANE_ENABLE + * and bus voting as usual + */ + ret = -EINVAL; + } + + val = ~(MAX_U32 << dev_req_params->lane_tx); + res = ufs_qcom_phy_set_tx_lane_enable(phy, val); + if (res) { + dev_err(hba->dev, "%s: ufs_qcom_phy_set_tx_lane_enable() failed res = %d\n", + __func__, res); + ret = res; + } + + /* cache the power mode parameters to use internally */ + memcpy(&host->dev_req_params, + dev_req_params, sizeof(*dev_req_params)); + break; + default: + ret = -EINVAL; + break; + } +out: + return ret; +} + +/** + * ufs_qcom_advertise_quirks - advertise the known QCOM UFS controller quirks + * @hba: host controller instance + * + * QCOM UFS host controller might have some non standard behaviours (quirks) + * than what is specified by UFSHCI specification. Advertise all such + * quirks to standard UFS host controller driver so standard takes them into + * account. + */ +static void ufs_qcom_advertise_quirks(struct ufs_hba *hba) +{ + u8 major; + u16 minor, step; + + ufs_qcom_get_controller_revision(hba, &major, &minor, &step); + + if ((major == 0x1) && (minor == 0x001) && (step == 0x0001)) + hba->quirks |= (UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS + | UFSHCD_QUIRK_BROKEN_INTR_AGGR + | UFSHCD_QUIRK_BROKEN_PA_RXHSUNTERMCAP + | UFSHCD_QUIRK_BROKEN_LCC); + else if ((major == 0x1) && (minor == 0x002) && (step == 0x0000)) + hba->quirks |= (UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS + | UFSHCD_QUIRK_BROKEN_PA_RXHSUNTERMCAP + | UFSHCD_QUIRK_BROKEN_LCC); +} + +static int ufs_qcom_setup_clocks(struct ufs_hba *hba, bool on) +{ + struct ufs_qcom_host *host = hba->priv; + int err = 0; + int vote = 0; + + /* + * In case ufs_qcom_init() is not yet done, simply ignore. + * This ufs_qcom_setup_clocks() shall be called from + * ufs_qcom_init() after init is done. + */ + if (!host) + return 0; + + if (on) { + err = ufs_qcom_phy_enable_iface_clk(host->generic_phy); + if (err) + goto out; + + vote = host->bus_vote.saved_vote; + } else { + /* M-PHY RMMI interface clocks can be turned off */ + ufs_qcom_phy_disable_iface_clk(host->generic_phy); + vote = host->bus_vote.min_bw_vote; + } + +out: + return err; +} + +#define ANDROID_BOOT_DEV_MAX 30 +static char android_boot_dev[ANDROID_BOOT_DEV_MAX]; +static int get_android_boot_dev(char *str) +{ + strlcpy(android_boot_dev, str, ANDROID_BOOT_DEV_MAX); + return 1; +} +__setup("androidboot.bootdevice=", get_android_boot_dev); + +/** + * ufs_qcom_init - bind phy with controller + * @hba: host controller instance + * + * Binds PHY with controller and powers up PHY enabling clocks + * and regulators. + * + * Returns -EPROBE_DEFER if binding fails, returns negative error + * on phy power up failure and returns zero on success. + */ +static int ufs_qcom_init(struct ufs_hba *hba) +{ + int err; + struct device *dev = hba->dev; + struct ufs_qcom_host *host; + + if (strlen(android_boot_dev) && strcmp(android_boot_dev, dev_name(dev))) + return -ENODEV; + + host = devm_kzalloc(dev, sizeof(*host), GFP_KERNEL); + if (!host) { + err = -ENOMEM; + dev_err(dev, "%s: no memory for qcom ufs host\n", __func__); + goto out; + } + + host->hba = hba; + host->generic_phy = devm_phy_get(dev, "ufsphy"); + + if (IS_ERR(host->generic_phy)) { + err = PTR_ERR(host->generic_phy); + dev_err(dev, "PHY get failed %d\n", err); + goto out; + } + + hba->priv = (void *)host; + + phy_init(host->generic_phy); + err = phy_power_on(host->generic_phy); + if (err) + goto out_phy_exit; + + err = ufs_qcom_init_lane_clks(host); + if (err) + goto out_disable_phy; + + ufs_qcom_advertise_quirks(hba); + + hba->caps |= UFSHCD_CAP_CLK_GATING | UFSHCD_CAP_CLK_SCALING; + hba->caps |= UFSHCD_CAP_AUTO_BKOPS_SUSPEND; + hba->caps |= UFSHCD_CAP_HIBERN8_WITH_CLK_GATING; + ufs_qcom_setup_clocks(hba, true); + goto out; + +out_disable_phy: + phy_power_off(host->generic_phy); +out_phy_exit: + phy_exit(host->generic_phy); + devm_kfree(dev, host); + hba->priv = NULL; +out: + return err; +} + +static void ufs_qcom_exit(struct ufs_hba *hba) +{ + struct ufs_qcom_host *host = hba->priv; + + ufs_qcom_disable_lane_clks(host); + phy_power_off(host->generic_phy); +} + + +void ufs_qcom_clk_scale_notify(struct ufs_hba *hba) +{ + struct ufs_qcom_host *host = hba->priv; + struct ufs_pa_layer_attr *dev_req_params = &host->dev_req_params; + + if (!dev_req_params) + return; + + ufs_qcom_cfg_timers(hba, dev_req_params->gear_rx, + dev_req_params->pwr_rx, + dev_req_params->hs_rate); +} + +/** + * struct ufs_hba_qcom_vops - UFS QCOM specific variant operations + * + * The variant operations configure the necessary controller and PHY + * handshake during initializaiton. + */ +const struct ufs_hba_variant_ops ufs_hba_qcom_vops = { + .name = "qcom", + .init = ufs_qcom_init, + .exit = ufs_qcom_exit, + .clk_scale_notify = ufs_qcom_clk_scale_notify, + .setup_clocks = ufs_qcom_setup_clocks, + .hce_enable_notify = ufs_qcom_hce_enable_notify, + .link_startup_notify = ufs_qcom_link_startup_notify, + .pwr_change_notify = ufs_qcom_pwr_change_notify, + .suspend = ufs_qcom_suspend, + .resume = ufs_qcom_resume, +}; +EXPORT_SYMBOL(ufs_hba_qcom_vops); diff --git a/drivers/scsi/ufs/ufs.h b/drivers/scsi/ufs/ufs.h deleted file mode 100644 index 42c459a..0000000 --- a/drivers/scsi/ufs/ufs.h +++ /dev/null @@ -1,491 +0,0 @@ -/* - * Universal Flash Storage Host controller driver - * - * This code is based on drivers/scsi/ufs/ufs.h - * Copyright (C) 2011-2013 Samsung India Software Operations - * - * Authors: - * Santosh Yaraganavi <santosh.sy@xxxxxxxxxxx> - * Vinayak Holikatti <h.vinayak@xxxxxxxxxxx> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * See the COPYING file in the top-level directory or visit - * <http://www.gnu.org/licenses/gpl-2.0.html> - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * This program is provided "AS IS" and "WITH ALL FAULTS" and - * without warranty of any kind. You are solely responsible for - * determining the appropriateness of using and distributing - * the program and assume all risks associated with your exercise - * of rights with respect to the program, including but not limited - * to infringement of third party rights, the risks and costs of - * program errors, damage to or loss of data, programs or equipment, - * and unavailability or interruption of operations. Under no - * circumstances will the contributor of this Program be liable for - * any damages of any kind arising from your use or distribution of - * this program. - */ - -#ifndef _UFS_H -#define _UFS_H - -#include <linux/mutex.h> -#include <linux/types.h> - -#define MAX_CDB_SIZE 16 -#define GENERAL_UPIU_REQUEST_SIZE 32 -#define QUERY_DESC_MAX_SIZE 255 -#define QUERY_DESC_MIN_SIZE 2 -#define QUERY_OSF_SIZE (GENERAL_UPIU_REQUEST_SIZE - \ - (sizeof(struct utp_upiu_header))) - -#define UPIU_HEADER_DWORD(byte3, byte2, byte1, byte0)\ - cpu_to_be32((byte3 << 24) | (byte2 << 16) |\ - (byte1 << 8) | (byte0)) -/* - * UFS device may have standard LUs and LUN id could be from 0x00 to - * 0x7F. Standard LUs use "Peripheral Device Addressing Format". - * UFS device may also have the Well Known LUs (also referred as W-LU) - * which again could be from 0x00 to 0x7F. For W-LUs, device only use - * the "Extended Addressing Format" which means the W-LUNs would be - * from 0xc100 (SCSI_W_LUN_BASE) onwards. - * This means max. LUN number reported from UFS device could be 0xC17F. - */ -#define UFS_UPIU_MAX_UNIT_NUM_ID 0x7F -#define UFS_MAX_LUNS (SCSI_W_LUN_BASE + UFS_UPIU_MAX_UNIT_NUM_ID) -#define UFS_UPIU_WLUN_ID (1 << 7) -#define UFS_UPIU_MAX_GENERAL_LUN 8 - -/* Well known logical unit id in LUN field of UPIU */ -enum { - UFS_UPIU_REPORT_LUNS_WLUN = 0x81, - UFS_UPIU_UFS_DEVICE_WLUN = 0xD0, - UFS_UPIU_BOOT_WLUN = 0xB0, - UFS_UPIU_RPMB_WLUN = 0xC4, -}; - -/* - * UFS Protocol Information Unit related definitions - */ - -/* Task management functions */ -enum { - UFS_ABORT_TASK = 0x01, - UFS_ABORT_TASK_SET = 0x02, - UFS_CLEAR_TASK_SET = 0x04, - UFS_LOGICAL_RESET = 0x08, - UFS_QUERY_TASK = 0x80, - UFS_QUERY_TASK_SET = 0x81, -}; - -/* UTP UPIU Transaction Codes Initiator to Target */ -enum { - UPIU_TRANSACTION_NOP_OUT = 0x00, - UPIU_TRANSACTION_COMMAND = 0x01, - UPIU_TRANSACTION_DATA_OUT = 0x02, - UPIU_TRANSACTION_TASK_REQ = 0x04, - UPIU_TRANSACTION_QUERY_REQ = 0x16, -}; - -/* UTP UPIU Transaction Codes Target to Initiator */ -enum { - UPIU_TRANSACTION_NOP_IN = 0x20, - UPIU_TRANSACTION_RESPONSE = 0x21, - UPIU_TRANSACTION_DATA_IN = 0x22, - UPIU_TRANSACTION_TASK_RSP = 0x24, - UPIU_TRANSACTION_READY_XFER = 0x31, - UPIU_TRANSACTION_QUERY_RSP = 0x36, - UPIU_TRANSACTION_REJECT_UPIU = 0x3F, -}; - -/* UPIU Read/Write flags */ -enum { - UPIU_CMD_FLAGS_NONE = 0x00, - UPIU_CMD_FLAGS_WRITE = 0x20, - UPIU_CMD_FLAGS_READ = 0x40, -}; - -/* UPIU Task Attributes */ -enum { - UPIU_TASK_ATTR_SIMPLE = 0x00, - UPIU_TASK_ATTR_ORDERED = 0x01, - UPIU_TASK_ATTR_HEADQ = 0x02, - UPIU_TASK_ATTR_ACA = 0x03, -}; - -/* UPIU Query request function */ -enum { - UPIU_QUERY_FUNC_STANDARD_READ_REQUEST = 0x01, - UPIU_QUERY_FUNC_STANDARD_WRITE_REQUEST = 0x81, -}; - -/* Flag idn for Query Requests*/ -enum flag_idn { - QUERY_FLAG_IDN_FDEVICEINIT = 0x01, - QUERY_FLAG_IDN_PWR_ON_WPE = 0x03, - QUERY_FLAG_IDN_BKOPS_EN = 0x04, -}; - -/* Attribute idn for Query requests */ -enum attr_idn { - QUERY_ATTR_IDN_ACTIVE_ICC_LVL = 0x03, - QUERY_ATTR_IDN_BKOPS_STATUS = 0x05, - QUERY_ATTR_IDN_EE_CONTROL = 0x0D, - QUERY_ATTR_IDN_EE_STATUS = 0x0E, -}; - -/* Descriptor idn for Query requests */ -enum desc_idn { - QUERY_DESC_IDN_DEVICE = 0x0, - QUERY_DESC_IDN_CONFIGURAION = 0x1, - QUERY_DESC_IDN_UNIT = 0x2, - QUERY_DESC_IDN_RFU_0 = 0x3, - QUERY_DESC_IDN_INTERCONNECT = 0x4, - QUERY_DESC_IDN_STRING = 0x5, - QUERY_DESC_IDN_RFU_1 = 0x6, - QUERY_DESC_IDN_GEOMETRY = 0x7, - QUERY_DESC_IDN_POWER = 0x8, - QUERY_DESC_IDN_MAX, -}; - -enum desc_header_offset { - QUERY_DESC_LENGTH_OFFSET = 0x00, - QUERY_DESC_DESC_TYPE_OFFSET = 0x01, -}; - -enum ufs_desc_max_size { - QUERY_DESC_DEVICE_MAX_SIZE = 0x1F, - QUERY_DESC_CONFIGURAION_MAX_SIZE = 0x90, - QUERY_DESC_UNIT_MAX_SIZE = 0x23, - QUERY_DESC_INTERCONNECT_MAX_SIZE = 0x06, - /* - * Max. 126 UNICODE characters (2 bytes per character) plus 2 bytes - * of descriptor header. - */ - QUERY_DESC_STRING_MAX_SIZE = 0xFE, - QUERY_DESC_GEOMETRY_MAZ_SIZE = 0x44, - QUERY_DESC_POWER_MAX_SIZE = 0x62, - QUERY_DESC_RFU_MAX_SIZE = 0x00, -}; - -/* Unit descriptor parameters offsets in bytes*/ -enum unit_desc_param { - UNIT_DESC_PARAM_LEN = 0x0, - UNIT_DESC_PARAM_TYPE = 0x1, - UNIT_DESC_PARAM_UNIT_INDEX = 0x2, - UNIT_DESC_PARAM_LU_ENABLE = 0x3, - UNIT_DESC_PARAM_BOOT_LUN_ID = 0x4, - UNIT_DESC_PARAM_LU_WR_PROTECT = 0x5, - UNIT_DESC_PARAM_LU_Q_DEPTH = 0x6, - UNIT_DESC_PARAM_MEM_TYPE = 0x8, - UNIT_DESC_PARAM_DATA_RELIABILITY = 0x9, - UNIT_DESC_PARAM_LOGICAL_BLK_SIZE = 0xA, - UNIT_DESC_PARAM_LOGICAL_BLK_COUNT = 0xB, - UNIT_DESC_PARAM_ERASE_BLK_SIZE = 0x13, - UNIT_DESC_PARAM_PROVISIONING_TYPE = 0x17, - UNIT_DESC_PARAM_PHY_MEM_RSRC_CNT = 0x18, - UNIT_DESC_PARAM_CTX_CAPABILITIES = 0x20, - UNIT_DESC_PARAM_LARGE_UNIT_SIZE_M1 = 0x22, -}; - -/* - * Logical Unit Write Protect - * 00h: LU not write protected - * 01h: LU write protected when fPowerOnWPEn =1 - * 02h: LU permanently write protected when fPermanentWPEn =1 - */ -enum ufs_lu_wp_type { - UFS_LU_NO_WP = 0x00, - UFS_LU_POWER_ON_WP = 0x01, - UFS_LU_PERM_WP = 0x02, -}; - -/* bActiveICCLevel parameter current units */ -enum { - UFSHCD_NANO_AMP = 0, - UFSHCD_MICRO_AMP = 1, - UFSHCD_MILI_AMP = 2, - UFSHCD_AMP = 3, -}; - -#define POWER_DESC_MAX_SIZE 0x62 -#define POWER_DESC_MAX_ACTV_ICC_LVLS 16 - -/* Attribute bActiveICCLevel parameter bit masks definitions */ -#define ATTR_ICC_LVL_UNIT_OFFSET 14 -#define ATTR_ICC_LVL_UNIT_MASK (0x3 << ATTR_ICC_LVL_UNIT_OFFSET) -#define ATTR_ICC_LVL_VALUE_MASK 0x3FF - -/* Power descriptor parameters offsets in bytes */ -enum power_desc_param_offset { - PWR_DESC_LEN = 0x0, - PWR_DESC_TYPE = 0x1, - PWR_DESC_ACTIVE_LVLS_VCC_0 = 0x2, - PWR_DESC_ACTIVE_LVLS_VCCQ_0 = 0x22, - PWR_DESC_ACTIVE_LVLS_VCCQ2_0 = 0x42, -}; - -/* Exception event mask values */ -enum { - MASK_EE_STATUS = 0xFFFF, - MASK_EE_URGENT_BKOPS = (1 << 2), -}; - -/* Background operation status */ -enum bkops_status { - BKOPS_STATUS_NO_OP = 0x0, - BKOPS_STATUS_NON_CRITICAL = 0x1, - BKOPS_STATUS_PERF_IMPACT = 0x2, - BKOPS_STATUS_CRITICAL = 0x3, - BKOPS_STATUS_MAX = BKOPS_STATUS_CRITICAL, -}; - -/* UTP QUERY Transaction Specific Fields OpCode */ -enum query_opcode { - UPIU_QUERY_OPCODE_NOP = 0x0, - UPIU_QUERY_OPCODE_READ_DESC = 0x1, - UPIU_QUERY_OPCODE_WRITE_DESC = 0x2, - UPIU_QUERY_OPCODE_READ_ATTR = 0x3, - UPIU_QUERY_OPCODE_WRITE_ATTR = 0x4, - UPIU_QUERY_OPCODE_READ_FLAG = 0x5, - UPIU_QUERY_OPCODE_SET_FLAG = 0x6, - UPIU_QUERY_OPCODE_CLEAR_FLAG = 0x7, - UPIU_QUERY_OPCODE_TOGGLE_FLAG = 0x8, -}; - -/* Query response result code */ -enum { - QUERY_RESULT_SUCCESS = 0x00, - QUERY_RESULT_NOT_READABLE = 0xF6, - QUERY_RESULT_NOT_WRITEABLE = 0xF7, - QUERY_RESULT_ALREADY_WRITTEN = 0xF8, - QUERY_RESULT_INVALID_LENGTH = 0xF9, - QUERY_RESULT_INVALID_VALUE = 0xFA, - QUERY_RESULT_INVALID_SELECTOR = 0xFB, - QUERY_RESULT_INVALID_INDEX = 0xFC, - QUERY_RESULT_INVALID_IDN = 0xFD, - QUERY_RESULT_INVALID_OPCODE = 0xFE, - QUERY_RESULT_GENERAL_FAILURE = 0xFF, -}; - -/* UTP Transfer Request Command Type (CT) */ -enum { - UPIU_COMMAND_SET_TYPE_SCSI = 0x0, - UPIU_COMMAND_SET_TYPE_UFS = 0x1, - UPIU_COMMAND_SET_TYPE_QUERY = 0x2, -}; - -/* UTP Transfer Request Command Offset */ -#define UPIU_COMMAND_TYPE_OFFSET 28 - -/* Offset of the response code in the UPIU header */ -#define UPIU_RSP_CODE_OFFSET 8 - -enum { - MASK_SCSI_STATUS = 0xFF, - MASK_TASK_RESPONSE = 0xFF00, - MASK_RSP_UPIU_RESULT = 0xFFFF, - MASK_QUERY_DATA_SEG_LEN = 0xFFFF, - MASK_RSP_UPIU_DATA_SEG_LEN = 0xFFFF, - MASK_RSP_EXCEPTION_EVENT = 0x10000, -}; - -/* Task management service response */ -enum { - UPIU_TASK_MANAGEMENT_FUNC_COMPL = 0x00, - UPIU_TASK_MANAGEMENT_FUNC_NOT_SUPPORTED = 0x04, - UPIU_TASK_MANAGEMENT_FUNC_SUCCEEDED = 0x08, - UPIU_TASK_MANAGEMENT_FUNC_FAILED = 0x05, - UPIU_INCORRECT_LOGICAL_UNIT_NO = 0x09, -}; - -/* UFS device power modes */ -enum ufs_dev_pwr_mode { - UFS_ACTIVE_PWR_MODE = 1, - UFS_SLEEP_PWR_MODE = 2, - UFS_POWERDOWN_PWR_MODE = 3, -}; - -/** - * struct utp_upiu_header - UPIU header structure - * @dword_0: UPIU header DW-0 - * @dword_1: UPIU header DW-1 - * @dword_2: UPIU header DW-2 - */ -struct utp_upiu_header { - __be32 dword_0; - __be32 dword_1; - __be32 dword_2; -}; - -/** - * struct utp_upiu_cmd - Command UPIU structure - * @data_transfer_len: Data Transfer Length DW-3 - * @cdb: Command Descriptor Block CDB DW-4 to DW-7 - */ -struct utp_upiu_cmd { - __be32 exp_data_transfer_len; - u8 cdb[MAX_CDB_SIZE]; -}; - -/** - * struct utp_upiu_query - upiu request buffer structure for - * query request. - * @opcode: command to perform B-0 - * @idn: a value that indicates the particular type of data B-1 - * @index: Index to further identify data B-2 - * @selector: Index to further identify data B-3 - * @reserved_osf: spec reserved field B-4,5 - * @length: number of descriptor bytes to read/write B-6,7 - * @value: Attribute value to be written DW-5 - * @reserved: spec reserved DW-6,7 - */ -struct utp_upiu_query { - u8 opcode; - u8 idn; - u8 index; - u8 selector; - __be16 reserved_osf; - __be16 length; - __be32 value; - __be32 reserved[2]; -}; - -/** - * struct utp_upiu_req - general upiu request structure - * @header:UPIU header structure DW-0 to DW-2 - * @sc: fields structure for scsi command DW-3 to DW-7 - * @qr: fields structure for query request DW-3 to DW-7 - */ -struct utp_upiu_req { - struct utp_upiu_header header; - union { - struct utp_upiu_cmd sc; - struct utp_upiu_query qr; - }; -}; - -/** - * struct utp_cmd_rsp - Response UPIU structure - * @residual_transfer_count: Residual transfer count DW-3 - * @reserved: Reserved double words DW-4 to DW-7 - * @sense_data_len: Sense data length DW-8 U16 - * @sense_data: Sense data field DW-8 to DW-12 - */ -struct utp_cmd_rsp { - __be32 residual_transfer_count; - __be32 reserved[4]; - __be16 sense_data_len; - u8 sense_data[18]; -}; - -/** - * struct utp_upiu_rsp - general upiu response structure - * @header: UPIU header structure DW-0 to DW-2 - * @sr: fields structure for scsi command DW-3 to DW-12 - * @qr: fields structure for query request DW-3 to DW-7 - */ -struct utp_upiu_rsp { - struct utp_upiu_header header; - union { - struct utp_cmd_rsp sr; - struct utp_upiu_query qr; - }; -}; - -/** - * struct utp_upiu_task_req - Task request UPIU structure - * @header - UPIU header structure DW0 to DW-2 - * @input_param1: Input parameter 1 DW-3 - * @input_param2: Input parameter 2 DW-4 - * @input_param3: Input parameter 3 DW-5 - * @reserved: Reserved double words DW-6 to DW-7 - */ -struct utp_upiu_task_req { - struct utp_upiu_header header; - __be32 input_param1; - __be32 input_param2; - __be32 input_param3; - __be32 reserved[2]; -}; - -/** - * struct utp_upiu_task_rsp - Task Management Response UPIU structure - * @header: UPIU header structure DW0-DW-2 - * @output_param1: Ouput parameter 1 DW3 - * @output_param2: Output parameter 2 DW4 - * @reserved: Reserved double words DW-5 to DW-7 - */ -struct utp_upiu_task_rsp { - struct utp_upiu_header header; - __be32 output_param1; - __be32 output_param2; - __be32 reserved[3]; -}; - -/** - * struct ufs_query_req - parameters for building a query request - * @query_func: UPIU header query function - * @upiu_req: the query request data - */ -struct ufs_query_req { - u8 query_func; - struct utp_upiu_query upiu_req; -}; - -/** - * struct ufs_query_resp - UPIU QUERY - * @response: device response code - * @upiu_res: query response data - */ -struct ufs_query_res { - u8 response; - struct utp_upiu_query upiu_res; -}; - -#define UFS_VREG_VCC_MIN_UV 2700000 /* uV */ -#define UFS_VREG_VCC_MAX_UV 3600000 /* uV */ -#define UFS_VREG_VCC_1P8_MIN_UV 1700000 /* uV */ -#define UFS_VREG_VCC_1P8_MAX_UV 1950000 /* uV */ -#define UFS_VREG_VCCQ_MIN_UV 1100000 /* uV */ -#define UFS_VREG_VCCQ_MAX_UV 1300000 /* uV */ -#define UFS_VREG_VCCQ2_MIN_UV 1650000 /* uV */ -#define UFS_VREG_VCCQ2_MAX_UV 1950000 /* uV */ - -/* - * VCCQ & VCCQ2 current requirement when UFS device is in sleep state - * and link is in Hibern8 state. - */ -#define UFS_VREG_LPM_LOAD_UA 1000 /* uA */ - -struct ufs_vreg { - struct regulator *reg; - const char *name; - bool enabled; - int min_uV; - int max_uV; - int min_uA; - int max_uA; -}; - -struct ufs_vreg_info { - struct ufs_vreg *vcc; - struct ufs_vreg *vccq; - struct ufs_vreg *vccq2; - struct ufs_vreg *vdd_hba; -}; - -struct ufs_dev_info { - bool f_power_on_wp_en; - /* Keeps information if any of the LU is power on write protected */ - bool is_lu_power_on_wp; -}; - -#endif /* End of Header */ diff --git a/drivers/scsi/ufs/ufshcd-pci.c b/drivers/scsi/ufs/ufshcd-pci.c index 955ed55..2a18b8e 100644 --- a/drivers/scsi/ufs/ufshcd-pci.c +++ b/drivers/scsi/ufs/ufshcd-pci.c @@ -33,7 +33,7 @@ * this program. */ -#include "ufshcd.h" +#include <linux/scsi/ufs/ufshcd.h> #include <linux/pci.h> #include <linux/pm_runtime.h> diff --git a/drivers/scsi/ufs/ufshcd-pltfrm.c b/drivers/scsi/ufs/ufshcd-pltfrm.c index 8adf067..d2b0ae6 100644 --- a/drivers/scsi/ufs/ufshcd-pltfrm.c +++ b/drivers/scsi/ufs/ufshcd-pltfrm.c @@ -37,7 +37,7 @@ #include <linux/pm_runtime.h> #include <linux/of.h> -#include "ufshcd.h" +#include <linux/scsi/ufs/ufshcd.h> static const struct of_device_id ufs_of_match[]; static struct ufs_hba_variant_ops *get_variant_ops(struct device *dev) diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c index a0a6d1a..e03a114 100644 --- a/drivers/scsi/ufs/ufshcd.c +++ b/drivers/scsi/ufs/ufshcd.c @@ -40,8 +40,9 @@ #include <linux/async.h> #include <linux/devfreq.h> -#include "ufshcd.h" -#include "unipro.h" +#include <linux/scsi/ufs/ufshcd.h> +#include <linux/scsi/ufs/unipro.h> +#include "ufshci.h" #define UFSHCD_ENABLE_INTRS (UTP_TRANSFER_REQ_COMPL |\ UTP_TASK_REQ_COMPL |\ @@ -2490,6 +2491,15 @@ out: } /** + * ufshcd_hba_stop - Send controller to reset state + * @hba: per adapter instance + */ +static inline void ufshcd_hba_stop(struct ufs_hba *hba) +{ + ufshcd_writel(hba, CONTROLLER_DISABLE, REG_CONTROLLER_ENABLE); +} + +/** * ufshcd_hba_enable - initialize the controller * @hba: per adapter instance * diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h deleted file mode 100644 index d502d70..0000000 --- a/drivers/scsi/ufs/ufshcd.h +++ /dev/null @@ -1,595 +0,0 @@ -/* - * Universal Flash Storage Host controller driver - * - * This code is based on drivers/scsi/ufs/ufshcd.h - * Copyright (C) 2011-2013 Samsung India Software Operations - * - * Authors: - * Santosh Yaraganavi <santosh.sy@xxxxxxxxxxx> - * Vinayak Holikatti <h.vinayak@xxxxxxxxxxx> - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * See the COPYING file in the top-level directory or visit - * <http://www.gnu.org/licenses/gpl-2.0.html> - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * This program is provided "AS IS" and "WITH ALL FAULTS" and - * without warranty of any kind. You are solely responsible for - * determining the appropriateness of using and distributing - * the program and assume all risks associated with your exercise - * of rights with respect to the program, including but not limited - * to infringement of third party rights, the risks and costs of - * program errors, damage to or loss of data, programs or equipment, - * and unavailability or interruption of operations. Under no - * circumstances will the contributor of this Program be liable for - * any damages of any kind arising from your use or distribution of - * this program. - */ - -#ifndef _UFSHCD_H -#define _UFSHCD_H - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/io.h> -#include <linux/delay.h> -#include <linux/slab.h> -#include <linux/spinlock.h> -#include <linux/workqueue.h> -#include <linux/errno.h> -#include <linux/types.h> -#include <linux/wait.h> -#include <linux/bitops.h> -#include <linux/pm_runtime.h> -#include <linux/clk.h> -#include <linux/completion.h> -#include <linux/regulator/consumer.h> - -#include <asm/irq.h> -#include <asm/byteorder.h> -#include <scsi/scsi.h> -#include <scsi/scsi_cmnd.h> -#include <scsi/scsi_host.h> -#include <scsi/scsi_tcq.h> -#include <scsi/scsi_dbg.h> -#include <scsi/scsi_eh.h> - -#include "ufs.h" -#include "ufshci.h" - -#define UFSHCD "ufshcd" -#define UFSHCD_DRIVER_VERSION "0.2" - -struct ufs_hba; - -enum dev_cmd_type { - DEV_CMD_TYPE_NOP = 0x0, - DEV_CMD_TYPE_QUERY = 0x1, -}; - -/** - * struct uic_command - UIC command structure - * @command: UIC command - * @argument1: UIC command argument 1 - * @argument2: UIC command argument 2 - * @argument3: UIC command argument 3 - * @cmd_active: Indicate if UIC command is outstanding - * @result: UIC command result - * @done: UIC command completion - */ -struct uic_command { - u32 command; - u32 argument1; - u32 argument2; - u32 argument3; - int cmd_active; - int result; - struct completion done; -}; - -/* Used to differentiate the power management options */ -enum ufs_pm_op { - UFS_RUNTIME_PM, - UFS_SYSTEM_PM, - UFS_SHUTDOWN_PM, -}; - -#define ufshcd_is_runtime_pm(op) ((op) == UFS_RUNTIME_PM) -#define ufshcd_is_system_pm(op) ((op) == UFS_SYSTEM_PM) -#define ufshcd_is_shutdown_pm(op) ((op) == UFS_SHUTDOWN_PM) - -/* Host <-> Device UniPro Link state */ -enum uic_link_state { - UIC_LINK_OFF_STATE = 0, /* Link powered down or disabled */ - UIC_LINK_ACTIVE_STATE = 1, /* Link is in Fast/Slow/Sleep state */ - UIC_LINK_HIBERN8_STATE = 2, /* Link is in Hibernate state */ -}; - -#define ufshcd_is_link_off(hba) ((hba)->uic_link_state == UIC_LINK_OFF_STATE) -#define ufshcd_is_link_active(hba) ((hba)->uic_link_state == \ - UIC_LINK_ACTIVE_STATE) -#define ufshcd_is_link_hibern8(hba) ((hba)->uic_link_state == \ - UIC_LINK_HIBERN8_STATE) -#define ufshcd_set_link_off(hba) ((hba)->uic_link_state = UIC_LINK_OFF_STATE) -#define ufshcd_set_link_active(hba) ((hba)->uic_link_state = \ - UIC_LINK_ACTIVE_STATE) -#define ufshcd_set_link_hibern8(hba) ((hba)->uic_link_state = \ - UIC_LINK_HIBERN8_STATE) - -/* - * UFS Power management levels. - * Each level is in increasing order of power savings. - */ -enum ufs_pm_level { - UFS_PM_LVL_0, /* UFS_ACTIVE_PWR_MODE, UIC_LINK_ACTIVE_STATE */ - UFS_PM_LVL_1, /* UFS_ACTIVE_PWR_MODE, UIC_LINK_HIBERN8_STATE */ - UFS_PM_LVL_2, /* UFS_SLEEP_PWR_MODE, UIC_LINK_ACTIVE_STATE */ - UFS_PM_LVL_3, /* UFS_SLEEP_PWR_MODE, UIC_LINK_HIBERN8_STATE */ - UFS_PM_LVL_4, /* UFS_POWERDOWN_PWR_MODE, UIC_LINK_HIBERN8_STATE */ - UFS_PM_LVL_5, /* UFS_POWERDOWN_PWR_MODE, UIC_LINK_OFF_STATE */ - UFS_PM_LVL_MAX -}; - -struct ufs_pm_lvl_states { - enum ufs_dev_pwr_mode dev_state; - enum uic_link_state link_state; -}; - -/** - * struct ufshcd_lrb - local reference block - * @utr_descriptor_ptr: UTRD address of the command - * @ucd_req_ptr: UCD address of the command - * @ucd_rsp_ptr: Response UPIU address for this command - * @ucd_prdt_ptr: PRDT address of the command - * @cmd: pointer to SCSI command - * @sense_buffer: pointer to sense buffer address of the SCSI command - * @sense_bufflen: Length of the sense buffer - * @scsi_status: SCSI status of the command - * @command_type: SCSI, UFS, Query. - * @task_tag: Task tag of the command - * @lun: LUN of the command - * @intr_cmd: Interrupt command (doesn't participate in interrupt aggregation) - */ -struct ufshcd_lrb { - struct utp_transfer_req_desc *utr_descriptor_ptr; - struct utp_upiu_req *ucd_req_ptr; - struct utp_upiu_rsp *ucd_rsp_ptr; - struct ufshcd_sg_entry *ucd_prdt_ptr; - - struct scsi_cmnd *cmd; - u8 *sense_buffer; - unsigned int sense_bufflen; - int scsi_status; - - int command_type; - int task_tag; - u8 lun; /* UPIU LUN id field is only 8-bit wide */ - bool intr_cmd; -}; - -/** - * struct ufs_query - holds relevent data structures for query request - * @request: request upiu and function - * @descriptor: buffer for sending/receiving descriptor - * @response: response upiu and response - */ -struct ufs_query { - struct ufs_query_req request; - u8 *descriptor; - struct ufs_query_res response; -}; - -/** - * struct ufs_dev_cmd - all assosiated fields with device management commands - * @type: device management command type - Query, NOP OUT - * @lock: lock to allow one command at a time - * @complete: internal commands completion - * @tag_wq: wait queue until free command slot is available - */ -struct ufs_dev_cmd { - enum dev_cmd_type type; - struct mutex lock; - struct completion *complete; - wait_queue_head_t tag_wq; - struct ufs_query query; -}; - -/** - * struct ufs_clk_info - UFS clock related info - * @list: list headed by hba->clk_list_head - * @clk: clock node - * @name: clock name - * @max_freq: maximum frequency supported by the clock - * @min_freq: min frequency that can be used for clock scaling - * @curr_freq: indicates the current frequency that it is set to - * @enabled: variable to check against multiple enable/disable - */ -struct ufs_clk_info { - struct list_head list; - struct clk *clk; - const char *name; - u32 max_freq; - u32 min_freq; - u32 curr_freq; - bool enabled; -}; - -#define PRE_CHANGE 0 -#define POST_CHANGE 1 - -struct ufs_pa_layer_attr { - u32 gear_rx; - u32 gear_tx; - u32 lane_rx; - u32 lane_tx; - u32 pwr_rx; - u32 pwr_tx; - u32 hs_rate; -}; - -struct ufs_pwr_mode_info { - bool is_valid; - struct ufs_pa_layer_attr info; -}; - -/** - * struct ufs_hba_variant_ops - variant specific callbacks - * @name: variant name - * @init: called when the driver is initialized - * @exit: called to cleanup everything done in init - * @clk_scale_notify: notifies that clks are scaled up/down - * @setup_clocks: called before touching any of the controller registers - * @setup_regulators: called before accessing the host controller - * @hce_enable_notify: called before and after HCE enable bit is set to allow - * variant specific Uni-Pro initialization. - * @link_startup_notify: called before and after Link startup is carried out - * to allow variant specific Uni-Pro initialization. - * @pwr_change_notify: called before and after a power mode change - * is carried out to allow vendor spesific capabilities - * to be set. - * @suspend: called during host controller PM callback - * @resume: called during host controller PM callback - */ -struct ufs_hba_variant_ops { - const char *name; - int (*init)(struct ufs_hba *); - void (*exit)(struct ufs_hba *); - void (*clk_scale_notify)(struct ufs_hba *); - int (*setup_clocks)(struct ufs_hba *, bool); - int (*setup_regulators)(struct ufs_hba *, bool); - int (*hce_enable_notify)(struct ufs_hba *, bool); - int (*link_startup_notify)(struct ufs_hba *, bool); - int (*pwr_change_notify)(struct ufs_hba *, - bool, struct ufs_pa_layer_attr *, - struct ufs_pa_layer_attr *); - int (*suspend)(struct ufs_hba *, enum ufs_pm_op); - int (*resume)(struct ufs_hba *, enum ufs_pm_op); -}; - -/* clock gating state */ -enum clk_gating_state { - CLKS_OFF, - CLKS_ON, - REQ_CLKS_OFF, - REQ_CLKS_ON, -}; - -/** - * struct ufs_clk_gating - UFS clock gating related info - * @gate_work: worker to turn off clocks after some delay as specified in - * delay_ms - * @ungate_work: worker to turn on clocks that will be used in case of - * interrupt context - * @state: the current clocks state - * @delay_ms: gating delay in ms - * @is_suspended: clk gating is suspended when set to 1 which can be used - * during suspend/resume - * @delay_attr: sysfs attribute to control delay_attr - * @active_reqs: number of requests that are pending and should be waited for - * completion before gating clocks. - */ -struct ufs_clk_gating { - struct delayed_work gate_work; - struct work_struct ungate_work; - enum clk_gating_state state; - unsigned long delay_ms; - bool is_suspended; - struct device_attribute delay_attr; - int active_reqs; -}; - -struct ufs_clk_scaling { - ktime_t busy_start_t; - bool is_busy_started; - unsigned long tot_busy_t; - unsigned long window_start_t; -}; - -/** - * struct ufs_init_prefetch - contains data that is pre-fetched once during - * initialization - * @icc_level: icc level which was read during initialization - */ -struct ufs_init_prefetch { - u32 icc_level; -}; - -/** - * struct ufs_hba - per adapter private structure - * @mmio_base: UFSHCI base register address - * @ucdl_base_addr: UFS Command Descriptor base address - * @utrdl_base_addr: UTP Transfer Request Descriptor base address - * @utmrdl_base_addr: UTP Task Management Descriptor base address - * @ucdl_dma_addr: UFS Command Descriptor DMA address - * @utrdl_dma_addr: UTRDL DMA address - * @utmrdl_dma_addr: UTMRDL DMA address - * @host: Scsi_Host instance of the driver - * @dev: device handle - * @lrb: local reference block - * @lrb_in_use: lrb in use - * @outstanding_tasks: Bits representing outstanding task requests - * @outstanding_reqs: Bits representing outstanding transfer requests - * @capabilities: UFS Controller Capabilities - * @nutrs: Transfer Request Queue depth supported by controller - * @nutmrs: Task Management Queue depth supported by controller - * @ufs_version: UFS Version to which controller complies - * @vops: pointer to variant specific operations - * @priv: pointer to variant specific private data - * @irq: Irq number of the controller - * @active_uic_cmd: handle of active UIC command - * @uic_cmd_mutex: mutex for uic command - * @tm_wq: wait queue for task management - * @tm_tag_wq: wait queue for free task management slots - * @tm_slots_in_use: bit map of task management request slots in use - * @pwr_done: completion for power mode change - * @tm_condition: condition variable for task management - * @ufshcd_state: UFSHCD states - * @eh_flags: Error handling flags - * @intr_mask: Interrupt Mask Bits - * @ee_ctrl_mask: Exception event control mask - * @is_powered: flag to check if HBA is powered - * @is_init_prefetch: flag to check if data was pre-fetched in initialization - * @init_prefetch_data: data pre-fetched during initialization - * @eh_work: Worker to handle UFS errors that require s/w attention - * @eeh_work: Worker to handle exception events - * @errors: HBA errors - * @uic_error: UFS interconnect layer error status - * @saved_err: sticky error mask - * @saved_uic_err: sticky UIC error mask - * @dev_cmd: ufs device management command information - * @auto_bkops_enabled: to track whether bkops is enabled in device - * @vreg_info: UFS device voltage regulator information - * @clk_list_head: UFS host controller clocks list node head - * @pwr_info: holds current power mode - * @max_pwr_info: keeps the device max valid pwm - */ -struct ufs_hba { - void __iomem *mmio_base; - - /* Virtual memory reference */ - struct utp_transfer_cmd_desc *ucdl_base_addr; - struct utp_transfer_req_desc *utrdl_base_addr; - struct utp_task_req_desc *utmrdl_base_addr; - - /* DMA memory reference */ - dma_addr_t ucdl_dma_addr; - dma_addr_t utrdl_dma_addr; - dma_addr_t utmrdl_dma_addr; - - struct Scsi_Host *host; - struct device *dev; - /* - * This field is to keep a reference to "scsi_device" corresponding to - * "UFS device" W-LU. - */ - struct scsi_device *sdev_ufs_device; - enum ufs_dev_pwr_mode curr_dev_pwr_mode; - enum uic_link_state uic_link_state; - /* Desired UFS power management level during runtime PM */ - enum ufs_pm_level rpm_lvl; - /* Desired UFS power management level during system PM */ - enum ufs_pm_level spm_lvl; - int pm_op_in_progress; - - struct ufshcd_lrb *lrb; - unsigned long lrb_in_use; - - unsigned long outstanding_tasks; - unsigned long outstanding_reqs; - - u32 capabilities; - int nutrs; - int nutmrs; - u32 ufs_version; - struct ufs_hba_variant_ops *vops; - void *priv; - unsigned int irq; - bool is_irq_enabled; - - - wait_queue_head_t tm_wq; - wait_queue_head_t tm_tag_wq; - unsigned long tm_condition; - unsigned long tm_slots_in_use; - - struct uic_command *active_uic_cmd; - struct mutex uic_cmd_mutex; - struct completion *uic_async_done; - - u32 ufshcd_state; - u32 eh_flags; - u32 intr_mask; - u16 ee_ctrl_mask; - bool is_powered; - bool is_init_prefetch; - struct ufs_init_prefetch init_prefetch_data; - - /* Work Queues */ - struct work_struct eh_work; - struct work_struct eeh_work; - - /* HBA Errors */ - u32 errors; - u32 uic_error; - u32 saved_err; - u32 saved_uic_err; - - /* Device management request data */ - struct ufs_dev_cmd dev_cmd; - - /* Keeps information of the UFS device connected to this host */ - struct ufs_dev_info dev_info; - bool auto_bkops_enabled; - struct ufs_vreg_info vreg_info; - struct list_head clk_list_head; - - bool wlun_dev_clr_ua; - - struct ufs_pa_layer_attr pwr_info; - struct ufs_pwr_mode_info max_pwr_info; - - struct ufs_clk_gating clk_gating; - /* Control to enable/disable host capabilities */ - u32 caps; - /* Allow dynamic clk gating */ -#define UFSHCD_CAP_CLK_GATING (1 << 0) - /* Allow hiberb8 with clk gating */ -#define UFSHCD_CAP_HIBERN8_WITH_CLK_GATING (1 << 1) - /* Allow dynamic clk scaling */ -#define UFSHCD_CAP_CLK_SCALING (1 << 2) - /* Allow auto bkops to enabled during runtime suspend */ -#define UFSHCD_CAP_AUTO_BKOPS_SUSPEND (1 << 3) - - struct devfreq *devfreq; - struct ufs_clk_scaling clk_scaling; - bool is_sys_suspended; -}; - -/* Returns true if clocks can be gated. Otherwise false */ -static inline bool ufshcd_is_clkgating_allowed(struct ufs_hba *hba) -{ - return hba->caps & UFSHCD_CAP_CLK_GATING; -} -static inline bool ufshcd_can_hibern8_during_gating(struct ufs_hba *hba) -{ - return hba->caps & UFSHCD_CAP_HIBERN8_WITH_CLK_GATING; -} -static inline int ufshcd_is_clkscaling_enabled(struct ufs_hba *hba) -{ - return hba->caps & UFSHCD_CAP_CLK_SCALING; -} -static inline bool ufshcd_can_autobkops_during_suspend(struct ufs_hba *hba) -{ - return hba->caps & UFSHCD_CAP_AUTO_BKOPS_SUSPEND; -} - -#define ufshcd_writel(hba, val, reg) \ - writel((val), (hba)->mmio_base + (reg)) -#define ufshcd_readl(hba, reg) \ - readl((hba)->mmio_base + (reg)) - -/** - * ufshcd_rmwl - read modify write into a register - * @hba - per adapter instance - * @mask - mask to apply on read value - * @val - actual value to write - * @reg - register address - */ -static inline void ufshcd_rmwl(struct ufs_hba *hba, u32 mask, u32 val, u32 reg) -{ - u32 tmp; - - tmp = ufshcd_readl(hba, reg); - tmp &= ~mask; - tmp |= (val & mask); - ufshcd_writel(hba, tmp, reg); -} - -int ufshcd_alloc_host(struct device *, struct ufs_hba **); -int ufshcd_init(struct ufs_hba * , void __iomem * , unsigned int); -void ufshcd_remove(struct ufs_hba *); - -/** - * ufshcd_hba_stop - Send controller to reset state - * @hba: per adapter instance - */ -static inline void ufshcd_hba_stop(struct ufs_hba *hba) -{ - ufshcd_writel(hba, CONTROLLER_DISABLE, REG_CONTROLLER_ENABLE); -} - -static inline void check_upiu_size(void) -{ - BUILD_BUG_ON(ALIGNED_UPIU_SIZE < - GENERAL_UPIU_REQUEST_SIZE + QUERY_DESC_MAX_SIZE); -} - -extern int ufshcd_runtime_suspend(struct ufs_hba *hba); -extern int ufshcd_runtime_resume(struct ufs_hba *hba); -extern int ufshcd_runtime_idle(struct ufs_hba *hba); -extern int ufshcd_system_suspend(struct ufs_hba *hba); -extern int ufshcd_system_resume(struct ufs_hba *hba); -extern int ufshcd_shutdown(struct ufs_hba *hba); -extern int ufshcd_dme_set_attr(struct ufs_hba *hba, u32 attr_sel, - u8 attr_set, u32 mib_val, u8 peer); -extern int ufshcd_dme_get_attr(struct ufs_hba *hba, u32 attr_sel, - u32 *mib_val, u8 peer); - -/* UIC command interfaces for DME primitives */ -#define DME_LOCAL 0 -#define DME_PEER 1 -#define ATTR_SET_NOR 0 /* NORMAL */ -#define ATTR_SET_ST 1 /* STATIC */ - -static inline int ufshcd_dme_set(struct ufs_hba *hba, u32 attr_sel, - u32 mib_val) -{ - return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR, - mib_val, DME_LOCAL); -} - -static inline int ufshcd_dme_st_set(struct ufs_hba *hba, u32 attr_sel, - u32 mib_val) -{ - return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_ST, - mib_val, DME_LOCAL); -} - -static inline int ufshcd_dme_peer_set(struct ufs_hba *hba, u32 attr_sel, - u32 mib_val) -{ - return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR, - mib_val, DME_PEER); -} - -static inline int ufshcd_dme_peer_st_set(struct ufs_hba *hba, u32 attr_sel, - u32 mib_val) -{ - return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_ST, - mib_val, DME_PEER); -} - -static inline int ufshcd_dme_get(struct ufs_hba *hba, - u32 attr_sel, u32 *mib_val) -{ - return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_LOCAL); -} - -static inline int ufshcd_dme_peer_get(struct ufs_hba *hba, - u32 attr_sel, u32 *mib_val) -{ - return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_PEER); -} - -int ufshcd_hold(struct ufs_hba *hba, bool async); -void ufshcd_release(struct ufs_hba *hba); -#endif /* End of Header */ diff --git a/drivers/scsi/ufs/unipro.h b/drivers/scsi/ufs/unipro.h deleted file mode 100644 index 3fc3e21..0000000 --- a/drivers/scsi/ufs/unipro.h +++ /dev/null @@ -1,207 +0,0 @@ -/* - * drivers/scsi/ufs/unipro.h - * - * Copyright (C) 2013 Samsung Electronics Co., Ltd. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ - -#ifndef _UNIPRO_H_ -#define _UNIPRO_H_ - -/* - * M-TX Configuration Attributes - */ -#define TX_MODE 0x0021 -#define TX_HSRATE_SERIES 0x0022 -#define TX_HSGEAR 0x0023 -#define TX_PWMGEAR 0x0024 -#define TX_AMPLITUDE 0x0025 -#define TX_HS_SLEWRATE 0x0026 -#define TX_SYNC_SOURCE 0x0027 -#define TX_HS_SYNC_LENGTH 0x0028 -#define TX_HS_PREPARE_LENGTH 0x0029 -#define TX_LS_PREPARE_LENGTH 0x002A -#define TX_HIBERN8_CONTROL 0x002B -#define TX_LCC_ENABLE 0x002C -#define TX_PWM_BURST_CLOSURE_EXTENSION 0x002D -#define TX_BYPASS_8B10B_ENABLE 0x002E -#define TX_DRIVER_POLARITY 0x002F -#define TX_HS_UNTERMINATED_LINE_DRIVE_ENABLE 0x0030 -#define TX_LS_TERMINATED_LINE_DRIVE_ENABLE 0x0031 -#define TX_LCC_SEQUENCER 0x0032 -#define TX_MIN_ACTIVATETIME 0x0033 -#define TX_PWM_G6_G7_SYNC_LENGTH 0x0034 - -/* - * M-RX Configuration Attributes - */ -#define RX_MODE 0x00A1 -#define RX_HSRATE_SERIES 0x00A2 -#define RX_HSGEAR 0x00A3 -#define RX_PWMGEAR 0x00A4 -#define RX_LS_TERMINATED_ENABLE 0x00A5 -#define RX_HS_UNTERMINATED_ENABLE 0x00A6 -#define RX_ENTER_HIBERN8 0x00A7 -#define RX_BYPASS_8B10B_ENABLE 0x00A8 -#define RX_TERMINATION_FORCE_ENABLE 0x0089 - -#define is_mphy_tx_attr(attr) (attr < RX_MODE) -/* - * PHY Adpater attributes - */ -#define PA_ACTIVETXDATALANES 0x1560 -#define PA_ACTIVERXDATALANES 0x1580 -#define PA_TXTRAILINGCLOCKS 0x1564 -#define PA_PHY_TYPE 0x1500 -#define PA_AVAILTXDATALANES 0x1520 -#define PA_AVAILRXDATALANES 0x1540 -#define PA_MINRXTRAILINGCLOCKS 0x1543 -#define PA_TXPWRSTATUS 0x1567 -#define PA_RXPWRSTATUS 0x1582 -#define PA_TXFORCECLOCK 0x1562 -#define PA_TXPWRMODE 0x1563 -#define PA_LEGACYDPHYESCDL 0x1570 -#define PA_MAXTXSPEEDFAST 0x1521 -#define PA_MAXTXSPEEDSLOW 0x1522 -#define PA_MAXRXSPEEDFAST 0x1541 -#define PA_MAXRXSPEEDSLOW 0x1542 -#define PA_TXLINKSTARTUPHS 0x1544 -#define PA_TXSPEEDFAST 0x1565 -#define PA_TXSPEEDSLOW 0x1566 -#define PA_REMOTEVERINFO 0x15A0 -#define PA_TXGEAR 0x1568 -#define PA_TXTERMINATION 0x1569 -#define PA_HSSERIES 0x156A -#define PA_PWRMODE 0x1571 -#define PA_RXGEAR 0x1583 -#define PA_RXTERMINATION 0x1584 -#define PA_MAXRXPWMGEAR 0x1586 -#define PA_MAXRXHSGEAR 0x1587 -#define PA_RXHSUNTERMCAP 0x15A5 -#define PA_RXLSTERMCAP 0x15A6 -#define PA_PACPREQTIMEOUT 0x1590 -#define PA_PACPREQEOBTIMEOUT 0x1591 -#define PA_HIBERN8TIME 0x15A7 -#define PA_LOCALVERINFO 0x15A9 -#define PA_TACTIVATE 0x15A8 -#define PA_PACPFRAMECOUNT 0x15C0 -#define PA_PACPERRORCOUNT 0x15C1 -#define PA_PHYTESTCONTROL 0x15C2 -#define PA_PWRMODEUSERDATA0 0x15B0 -#define PA_PWRMODEUSERDATA1 0x15B1 -#define PA_PWRMODEUSERDATA2 0x15B2 -#define PA_PWRMODEUSERDATA3 0x15B3 -#define PA_PWRMODEUSERDATA4 0x15B4 -#define PA_PWRMODEUSERDATA5 0x15B5 -#define PA_PWRMODEUSERDATA6 0x15B6 -#define PA_PWRMODEUSERDATA7 0x15B7 -#define PA_PWRMODEUSERDATA8 0x15B8 -#define PA_PWRMODEUSERDATA9 0x15B9 -#define PA_PWRMODEUSERDATA10 0x15BA -#define PA_PWRMODEUSERDATA11 0x15BB -#define PA_CONNECTEDTXDATALANES 0x1561 -#define PA_CONNECTEDRXDATALANES 0x1581 -#define PA_LOGICALLANEMAP 0x15A1 -#define PA_SLEEPNOCONFIGTIME 0x15A2 -#define PA_STALLNOCONFIGTIME 0x15A3 -#define PA_SAVECONFIGTIME 0x15A4 - -/* PA power modes */ -enum { - FAST_MODE = 1, - SLOW_MODE = 2, - FASTAUTO_MODE = 4, - SLOWAUTO_MODE = 5, - UNCHANGED = 7, -}; - -/* PA TX/RX Frequency Series */ -enum { - PA_HS_MODE_A = 1, - PA_HS_MODE_B = 2, -}; - -enum ufs_pwm_gear_tag { - UFS_PWM_DONT_CHANGE, /* Don't change Gear */ - UFS_PWM_G1, /* PWM Gear 1 (default for reset) */ - UFS_PWM_G2, /* PWM Gear 2 */ - UFS_PWM_G3, /* PWM Gear 3 */ - UFS_PWM_G4, /* PWM Gear 4 */ - UFS_PWM_G5, /* PWM Gear 5 */ - UFS_PWM_G6, /* PWM Gear 6 */ - UFS_PWM_G7, /* PWM Gear 7 */ -}; - -enum ufs_hs_gear_tag { - UFS_HS_DONT_CHANGE, /* Don't change Gear */ - UFS_HS_G1, /* HS Gear 1 (default for reset) */ - UFS_HS_G2, /* HS Gear 2 */ - UFS_HS_G3, /* HS Gear 3 */ -}; - -/* - * Data Link Layer Attributes - */ -#define DL_TC0TXFCTHRESHOLD 0x2040 -#define DL_FC0PROTTIMEOUTVAL 0x2041 -#define DL_TC0REPLAYTIMEOUTVAL 0x2042 -#define DL_AFC0REQTIMEOUTVAL 0x2043 -#define DL_AFC0CREDITTHRESHOLD 0x2044 -#define DL_TC0OUTACKTHRESHOLD 0x2045 -#define DL_TC1TXFCTHRESHOLD 0x2060 -#define DL_FC1PROTTIMEOUTVAL 0x2061 -#define DL_TC1REPLAYTIMEOUTVAL 0x2062 -#define DL_AFC1REQTIMEOUTVAL 0x2063 -#define DL_AFC1CREDITTHRESHOLD 0x2064 -#define DL_TC1OUTACKTHRESHOLD 0x2065 -#define DL_TXPREEMPTIONCAP 0x2000 -#define DL_TC0TXMAXSDUSIZE 0x2001 -#define DL_TC0RXINITCREDITVAL 0x2002 -#define DL_TC0TXBUFFERSIZE 0x2005 -#define DL_PEERTC0PRESENT 0x2046 -#define DL_PEERTC0RXINITCREVAL 0x2047 -#define DL_TC1TXMAXSDUSIZE 0x2003 -#define DL_TC1RXINITCREDITVAL 0x2004 -#define DL_TC1TXBUFFERSIZE 0x2006 -#define DL_PEERTC1PRESENT 0x2066 -#define DL_PEERTC1RXINITCREVAL 0x2067 - -/* - * Network Layer Attributes - */ -#define N_DEVICEID 0x3000 -#define N_DEVICEID_VALID 0x3001 -#define N_TC0TXMAXSDUSIZE 0x3020 -#define N_TC1TXMAXSDUSIZE 0x3021 - -/* - * Transport Layer Attributes - */ -#define T_NUMCPORTS 0x4000 -#define T_NUMTESTFEATURES 0x4001 -#define T_CONNECTIONSTATE 0x4020 -#define T_PEERDEVICEID 0x4021 -#define T_PEERCPORTID 0x4022 -#define T_TRAFFICCLASS 0x4023 -#define T_PROTOCOLID 0x4024 -#define T_CPORTFLAGS 0x4025 -#define T_TXTOKENVALUE 0x4026 -#define T_RXTOKENVALUE 0x4027 -#define T_LOCALBUFFERSPACE 0x4028 -#define T_PEERBUFFERSPACE 0x4029 -#define T_CREDITSTOSEND 0x402A -#define T_CPORTMODE 0x402B -#define T_TC0TXMAXSDUSIZE 0x4060 -#define T_TC1TXMAXSDUSIZE 0x4061 - -/* Boolean attribute values */ -enum { - FALSE = 0, - TRUE, -}; - -#endif /* _UNIPRO_H_ */ diff --git a/include/linux/phy/phy-qcom-ufs.h b/include/linux/phy/phy-qcom-ufs.h new file mode 100644 index 0000000..f8eeb4c --- /dev/null +++ b/include/linux/phy/phy-qcom-ufs.h @@ -0,0 +1,202 @@ +/* + * Copyright (c) 2013-2014, Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef UFS_QCOM_PHY_H_ +#define UFS_QCOM_PHY_H_ + +#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/time.h> +#include <linux/clk.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/phy/phy.h> + +#include <linux/scsi/ufs/ufshcd.h> +#include <linux/scsi/ufs/unipro.h> +#include <linux/scsi/ufs/ufs-qcom.h> + +#define UFS_QCOM_PHY_CAL_ENTRY(reg, val) \ + { \ + .reg_offset = reg, \ + .cfg_value = val, \ + } + +#define UFS_QCOM_PHY_NAME_LEN 30 + +enum { + MASK_SERDES_START = 0x1, + MASK_PCS_READY = 0x1, +}; + +enum { + OFFSET_SERDES_START = 0x0, +}; + +struct ufs_qcom_phy_stored_attributes { + u32 att; + u32 value; +}; + +struct ufs_qcom_phy_calibration { + u32 reg_offset; + u32 cfg_value; +}; + +struct ufs_qcom_phy { + struct list_head list; + struct device *dev; + void __iomem *mmio; + struct clk *tx_iface_clk; + struct clk *rx_iface_clk; + bool is_iface_clk_enabled; + struct clk *ref_clk_src; + struct clk *ref_clk_parent; + struct clk *ref_clk; + bool is_ref_clk_enabled; + struct ufs_qcom_phy_vreg vdda_pll; + struct ufs_qcom_phy_vreg vdda_phy; + unsigned int quirks; + u8 host_ctrl_rev_major; + u16 host_ctrl_rev_minor; + u16 host_ctrl_rev_step; + + /* + * As part of UFS power management, UFS link would be put in hibernate + * and UFS device would be put in SLEEP mode as part of runtime/system + * suspend callback. But when system goes into suspend with VDD + * minimization, UFS PHY states are being reset which means UFS link + * hibernate exit command on system resume would fail. + * If this quirk is enabled then above issue is workaround by saving + * the UFS PHY state information before system goes into suspend and + * restoring the saved state information during system resume but + * before executing the hibern8 exit command. + * Note that this quirk will help restoring the PHY state if even when + * link in not kept in hibern8 during suspend. + * + * Here is the list of steps to save/restore the configuration: + * Before entering into system suspend: + * 1. Read Critical PCS SWI Registers + less critical PHY CSR + * 2. Read RMMI Attributes + * Enter into system suspend + * After exiting from system suspend: + * 1. Set UFS_PHY_SOFT_RESET bit in UFS_CFG1 register of the UFS + * Controller + * 2. Write 0x01 to the UFS_PHY_POWER_DOWN_CONTROL register in the + * UFS PHY + * 3. Write back the values of the PHY SWI registers + * 4. Clear UFS_PHY_SOFT_RESET bit in UFS_CFG1 register of the UFS + * Controller + * 5. Write 0x01 to the UFS_PHY_PHY_START in the UFS PHY. This will + * start the PLL calibration and bring-up of the PHY. + * 6. Write back the values to the PHY RMMI Attributes + * 7. Wait for UFS_PHY_PCS_READY_STATUS[0] to be '1' + */ + #define UFS_QCOM_PHY_QUIRK_CFG_RESTORE (1 << 0) + + /* + * If UFS PHY power down is deasserted and power is restored to analog + * circuits, the rx_sigdet can glitch. If the glitch is wide enough, + * it can trigger the digital logic to think it saw a DIF-N and cause + * it to exit Hibern8. Disabling the rx_sigdet during power-up masks + * the glitch. + */ + #define UFS_QCOM_PHY_DIS_SIGDET_BEFORE_PWR_COLLAPSE (1 << 1) + + /* + * If UFS link is put into Hibern8 and if UFS PHY analog hardware is + * power collapsed (by clearing UFS_PHY_POWER_DOWN_CONTROL), Hibern8 + * exit might fail even after powering on UFS PHY analog hardware. + * Enabling this quirk will help to solve above issue by doing + * custom PHY settings just before PHY analog power collapse. + */ + #define UFS_QCOM_PHY_QUIRK_HIBERN8_EXIT_AFTER_PHY_PWR_COLLAPSE (1 << 2) + + char name[UFS_QCOM_PHY_NAME_LEN]; + struct ufs_qcom_phy_calibration *cached_regs; + int cached_regs_table_size; + bool is_powered_on; + struct ufs_qcom_phy_specific_ops *phy_spec_ops; +}; + +/** + * struct ufs_qcom_phy_specific_ops - set of pointers to functions which have a + * specific implementation per phy. Each UFS phy, should implement + * those functions according to its spec and requirements + * @calibrate_phy: pointer to a function that calibrate the phy + * @start_serdes: pointer to a function that starts the serdes + * @save_configuration: pointer to a function that saves phy + * configuration + * @is_physical_coding_sublayer_ready: pointer to a function that + * checks pcs readiness + * @set_tx_lane_enable: pointer to a function that enable tx lanes + * @power_control: pointer to a function that controls analog rail of phy + * and writes to QSERDES_RX_SIGDET_CNTRL attribute + */ +struct ufs_qcom_phy_specific_ops { + int (*calibrate_phy)(struct ufs_qcom_phy *phy); + void (*start_serdes)(struct ufs_qcom_phy *phy); + void (*save_configuration)(struct ufs_qcom_phy *phy); + void (*restore_configuration)(struct ufs_qcom_phy *phy); + int (*is_physical_coding_sublayer_ready)(struct ufs_qcom_phy *phy); + void (*set_tx_lane_enable)(struct ufs_qcom_phy *phy, u32 val); + void (*power_control)(struct ufs_qcom_phy *phy, bool val); +}; + +int ufs_qcom_phy_init_vreg(struct phy *phy, + struct ufs_qcom_phy_vreg *vreg, const char *name); +int ufs_qcom_phy_cfg_vreg(struct phy *phy, + struct ufs_qcom_phy_vreg *vreg, bool on); +int ufs_qcom_phy_enable_vreg(struct phy *phy, + struct ufs_qcom_phy_vreg *vreg); +int ufs_qcom_phy_disable_vreg(struct phy *phy, + struct ufs_qcom_phy_vreg *vreg); +int ufs_qcom_phy_enable_ref_clk(struct phy *phy); +void ufs_qcom_phy_disable_ref_clk(struct phy *phy); +int ufs_qcom_phy_enable_iface_clk(struct phy *phy); +void ufs_qcom_phy_disable_iface_clk(struct phy *phy); +void ufs_qcom_phy_restore_swi_regs(struct phy *phy); +int ufs_qcom_phy_link_startup_post_change(struct phy *phy, + struct ufs_hba *hba); +int ufs_qcom_phy_base_init(struct platform_device *pdev, + struct ufs_qcom_phy *ufs_qcom_phy_ops); +int ufs_qcom_phy_is_cfg_restore_quirk_enabled(struct phy *phy); +struct ufs_qcom_phy *get_ufs_qcom_phy(struct phy *generic_phy); +int ufs_qcom_phy_start_serdes(struct phy *generic_phy); +int ufs_qcom_phy_set_tx_lane_enable(struct phy *generic_phy, u32 tx_lanes); +int ufs_qcom_phy_calibrate_phy(struct phy *generic_phy); +int ufs_qcom_phy_is_pcs_ready(struct phy *generic_phy); +int ufs_qcom_phy_save_configuration(struct phy *generic_phy); +int ufs_qcom_phy_restore_configuration(struct phy *generic_phy); +void ufs_qcom_phy_save_controller_version(struct phy *generic_phy, + u8 major, u16 minor, u16 step); +int ufs_qcom_phy_power_on(struct phy *generic_phy); +int ufs_qcom_phy_power_off(struct phy *generic_phy); +int ufs_qcom_phy_exit(struct phy *generic_phy); +int ufs_qcom_phy_init_clks(struct phy *generic_phy, + struct ufs_qcom_phy *phy_common); +int ufs_qcom_phy_init_vregulators(struct phy *generic_phy, + struct ufs_qcom_phy *phy_common); +int ufs_qcom_phy_remove(struct phy *generic_phy, + struct ufs_qcom_phy *ufs_qcom_phy); +struct phy *ufs_qcom_phy_generic_probe(struct platform_device *pdev, + struct ufs_qcom_phy *common_cfg, + struct phy_ops *ufs_qcom_phy_gen_ops, + struct ufs_qcom_phy_specific_ops *phy_spec_ops); +int ufs_qcom_phy_calibrate(struct ufs_qcom_phy *ufs_qcom_phy, + struct ufs_qcom_phy_calibration *tbl_A, int tbl_size_A, + struct ufs_qcom_phy_calibration *tbl_B, int tbl_size_B, + int rate); +#endif diff --git a/include/linux/scsi/ufs/ufs-qcom.h b/include/linux/scsi/ufs/ufs-qcom.h new file mode 100644 index 0000000..d32a3af --- /dev/null +++ b/include/linux/scsi/ufs/ufs-qcom.h @@ -0,0 +1,156 @@ +/* Copyright (c) 2013-2014, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef UFS_QCOM_H_ +#define UFS_QCOM_H_ + +#include <linux/phy/phy.h> + +#define MAX_U32 (~(u32)0) +#define MPHY_TX_FSM_STATE 0x41 +#define TX_FSM_HIBERN8 0x1 +#define HBRN8_POLL_TOUT_MS 100 +#define DEFAULT_CLK_RATE_HZ 1000000 +#define BUS_VECTOR_NAME_LEN 32 + +#define UFS_HW_VER_MAJOR_SHFT (28) +#define UFS_HW_VER_MAJOR_MASK (0x000F << UFS_HW_VER_MAJOR_SHFT) +#define UFS_HW_VER_MINOR_SHFT (16) +#define UFS_HW_VER_MINOR_MASK (0x0FFF << UFS_HW_VER_MINOR_SHFT) +#define UFS_HW_VER_STEP_SHFT (0) +#define UFS_HW_VER_STEP_MASK (0xFFFF << UFS_HW_VER_STEP_SHFT) + +/* vendor specific pre-defined parameters */ +#define SLOW 1 +#define FAST 2 + +#define UFS_QCOM_LIMIT_NUM_LANES_RX 2 +#define UFS_QCOM_LIMIT_NUM_LANES_TX 2 +#define UFS_QCOM_LIMIT_HSGEAR_RX UFS_HS_G2 +#define UFS_QCOM_LIMIT_HSGEAR_TX UFS_HS_G2 +#define UFS_QCOM_LIMIT_PWMGEAR_RX UFS_PWM_G4 +#define UFS_QCOM_LIMIT_PWMGEAR_TX UFS_PWM_G4 +#define UFS_QCOM_LIMIT_RX_PWR_PWM SLOW_MODE +#define UFS_QCOM_LIMIT_TX_PWR_PWM SLOW_MODE +#define UFS_QCOM_LIMIT_RX_PWR_HS FAST_MODE +#define UFS_QCOM_LIMIT_TX_PWR_HS FAST_MODE +#define UFS_QCOM_LIMIT_HS_RATE PA_HS_MODE_B +#define UFS_QCOM_LIMIT_DESIRED_MODE FAST + +/* QCOM UFS host controller vendor specific registers */ +enum { + REG_UFS_SYS1CLK_1US = 0xC0, + REG_UFS_TX_SYMBOL_CLK_NS_US = 0xC4, + REG_UFS_LOCAL_PORT_ID_REG = 0xC8, + REG_UFS_PA_ERR_CODE = 0xCC, + REG_UFS_RETRY_TIMER_REG = 0xD0, + REG_UFS_PA_LINK_STARTUP_TIMER = 0xD8, + REG_UFS_CFG1 = 0xDC, + REG_UFS_CFG2 = 0xE0, + REG_UFS_HW_VERSION = 0xE4, +}; + +/* bit offset */ +enum { + OFFSET_UFS_PHY_SOFT_RESET = 1, + OFFSET_CLK_NS_REG = 10, +}; + +/* bit masks */ +enum { + MASK_UFS_PHY_SOFT_RESET = 0x2, + MASK_TX_SYMBOL_CLK_1US_REG = 0x3FF, + MASK_CLK_NS_REG = 0xFFFC00, +}; + +enum ufs_qcom_phy_init_type { + UFS_PHY_INIT_FULL, + UFS_PHY_INIT_CFG_RESTORE, +}; + +struct ufs_qcom_phy_vreg { + const char *name; + struct regulator *reg; + int max_uA; + int min_uV; + int max_uV; + bool enabled; +}; + +static inline void +ufs_qcom_get_controller_revision(struct ufs_hba *hba, + u8 *major, u16 *minor, u16 *step) +{ + u32 ver = ufshcd_readl(hba, REG_UFS_HW_VERSION); + + *major = (ver & UFS_HW_VER_MAJOR_MASK) >> UFS_HW_VER_MAJOR_SHFT; + *minor = (ver & UFS_HW_VER_MINOR_MASK) >> UFS_HW_VER_MINOR_SHFT; + *step = (ver & UFS_HW_VER_STEP_MASK) >> UFS_HW_VER_STEP_SHFT; +}; + +static inline void ufs_qcom_assert_reset(struct ufs_hba *hba) +{ + ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, + 1 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1); + /* + * ensure that controller writes MASK_UFS_PHY_SOFT_RESET + * before it continues + */ + mb(); +} + +static inline void ufs_qcom_deassert_reset(struct ufs_hba *hba) +{ + ufshcd_rmwl(hba, MASK_UFS_PHY_SOFT_RESET, + 0 << OFFSET_UFS_PHY_SOFT_RESET, REG_UFS_CFG1); + /* + * ensure that controller writes MASK_UFS_PHY_SOFT_RESET + * before it continues + */ + mb(); +} + +struct ufs_qcom_bus_vote { + uint32_t client_handle; + uint32_t curr_vote; + int min_bw_vote; + int max_bw_vote; + int saved_vote; + bool is_max_bw_needed; + struct device_attribute max_bus_bw; +}; + +struct ufs_qcom_host { + struct phy *generic_phy; + struct ufs_hba *hba; + struct ufs_qcom_bus_vote bus_vote; + struct ufs_pa_layer_attr dev_req_params; + struct clk *rx_l0_sync_clk; + struct clk *tx_l0_sync_clk; + struct clk *rx_l1_sync_clk; + struct clk *tx_l1_sync_clk; + bool is_lane_clks_enabled; + bool sec_cfg_updated; +}; + +#define ufs_qcom_is_link_off(hba) ufshcd_is_link_off(hba) +#define ufs_qcom_is_link_active(hba) ufshcd_is_link_active(hba) +#define ufs_qcom_is_link_hibern8(hba) ufshcd_is_link_hibern8(hba) + +#define MAX_PROP_NAME 32 +#define VDDA_PHY_MIN_UV 1000000 +#define VDDA_PHY_MAX_UV 1000000 +#define VDDA_PLL_MIN_UV 1800000 +#define VDDA_PLL_MAX_UV 1800000 + +#endif /* UFS_QCOM_H_ */ diff --git a/include/linux/scsi/ufs/ufs.h b/include/linux/scsi/ufs/ufs.h new file mode 100644 index 0000000..42c459a --- /dev/null +++ b/include/linux/scsi/ufs/ufs.h @@ -0,0 +1,491 @@ +/* + * Universal Flash Storage Host controller driver + * + * This code is based on drivers/scsi/ufs/ufs.h + * Copyright (C) 2011-2013 Samsung India Software Operations + * + * Authors: + * Santosh Yaraganavi <santosh.sy@xxxxxxxxxxx> + * Vinayak Holikatti <h.vinayak@xxxxxxxxxxx> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * See the COPYING file in the top-level directory or visit + * <http://www.gnu.org/licenses/gpl-2.0.html> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * This program is provided "AS IS" and "WITH ALL FAULTS" and + * without warranty of any kind. You are solely responsible for + * determining the appropriateness of using and distributing + * the program and assume all risks associated with your exercise + * of rights with respect to the program, including but not limited + * to infringement of third party rights, the risks and costs of + * program errors, damage to or loss of data, programs or equipment, + * and unavailability or interruption of operations. Under no + * circumstances will the contributor of this Program be liable for + * any damages of any kind arising from your use or distribution of + * this program. + */ + +#ifndef _UFS_H +#define _UFS_H + +#include <linux/mutex.h> +#include <linux/types.h> + +#define MAX_CDB_SIZE 16 +#define GENERAL_UPIU_REQUEST_SIZE 32 +#define QUERY_DESC_MAX_SIZE 255 +#define QUERY_DESC_MIN_SIZE 2 +#define QUERY_OSF_SIZE (GENERAL_UPIU_REQUEST_SIZE - \ + (sizeof(struct utp_upiu_header))) + +#define UPIU_HEADER_DWORD(byte3, byte2, byte1, byte0)\ + cpu_to_be32((byte3 << 24) | (byte2 << 16) |\ + (byte1 << 8) | (byte0)) +/* + * UFS device may have standard LUs and LUN id could be from 0x00 to + * 0x7F. Standard LUs use "Peripheral Device Addressing Format". + * UFS device may also have the Well Known LUs (also referred as W-LU) + * which again could be from 0x00 to 0x7F. For W-LUs, device only use + * the "Extended Addressing Format" which means the W-LUNs would be + * from 0xc100 (SCSI_W_LUN_BASE) onwards. + * This means max. LUN number reported from UFS device could be 0xC17F. + */ +#define UFS_UPIU_MAX_UNIT_NUM_ID 0x7F +#define UFS_MAX_LUNS (SCSI_W_LUN_BASE + UFS_UPIU_MAX_UNIT_NUM_ID) +#define UFS_UPIU_WLUN_ID (1 << 7) +#define UFS_UPIU_MAX_GENERAL_LUN 8 + +/* Well known logical unit id in LUN field of UPIU */ +enum { + UFS_UPIU_REPORT_LUNS_WLUN = 0x81, + UFS_UPIU_UFS_DEVICE_WLUN = 0xD0, + UFS_UPIU_BOOT_WLUN = 0xB0, + UFS_UPIU_RPMB_WLUN = 0xC4, +}; + +/* + * UFS Protocol Information Unit related definitions + */ + +/* Task management functions */ +enum { + UFS_ABORT_TASK = 0x01, + UFS_ABORT_TASK_SET = 0x02, + UFS_CLEAR_TASK_SET = 0x04, + UFS_LOGICAL_RESET = 0x08, + UFS_QUERY_TASK = 0x80, + UFS_QUERY_TASK_SET = 0x81, +}; + +/* UTP UPIU Transaction Codes Initiator to Target */ +enum { + UPIU_TRANSACTION_NOP_OUT = 0x00, + UPIU_TRANSACTION_COMMAND = 0x01, + UPIU_TRANSACTION_DATA_OUT = 0x02, + UPIU_TRANSACTION_TASK_REQ = 0x04, + UPIU_TRANSACTION_QUERY_REQ = 0x16, +}; + +/* UTP UPIU Transaction Codes Target to Initiator */ +enum { + UPIU_TRANSACTION_NOP_IN = 0x20, + UPIU_TRANSACTION_RESPONSE = 0x21, + UPIU_TRANSACTION_DATA_IN = 0x22, + UPIU_TRANSACTION_TASK_RSP = 0x24, + UPIU_TRANSACTION_READY_XFER = 0x31, + UPIU_TRANSACTION_QUERY_RSP = 0x36, + UPIU_TRANSACTION_REJECT_UPIU = 0x3F, +}; + +/* UPIU Read/Write flags */ +enum { + UPIU_CMD_FLAGS_NONE = 0x00, + UPIU_CMD_FLAGS_WRITE = 0x20, + UPIU_CMD_FLAGS_READ = 0x40, +}; + +/* UPIU Task Attributes */ +enum { + UPIU_TASK_ATTR_SIMPLE = 0x00, + UPIU_TASK_ATTR_ORDERED = 0x01, + UPIU_TASK_ATTR_HEADQ = 0x02, + UPIU_TASK_ATTR_ACA = 0x03, +}; + +/* UPIU Query request function */ +enum { + UPIU_QUERY_FUNC_STANDARD_READ_REQUEST = 0x01, + UPIU_QUERY_FUNC_STANDARD_WRITE_REQUEST = 0x81, +}; + +/* Flag idn for Query Requests*/ +enum flag_idn { + QUERY_FLAG_IDN_FDEVICEINIT = 0x01, + QUERY_FLAG_IDN_PWR_ON_WPE = 0x03, + QUERY_FLAG_IDN_BKOPS_EN = 0x04, +}; + +/* Attribute idn for Query requests */ +enum attr_idn { + QUERY_ATTR_IDN_ACTIVE_ICC_LVL = 0x03, + QUERY_ATTR_IDN_BKOPS_STATUS = 0x05, + QUERY_ATTR_IDN_EE_CONTROL = 0x0D, + QUERY_ATTR_IDN_EE_STATUS = 0x0E, +}; + +/* Descriptor idn for Query requests */ +enum desc_idn { + QUERY_DESC_IDN_DEVICE = 0x0, + QUERY_DESC_IDN_CONFIGURAION = 0x1, + QUERY_DESC_IDN_UNIT = 0x2, + QUERY_DESC_IDN_RFU_0 = 0x3, + QUERY_DESC_IDN_INTERCONNECT = 0x4, + QUERY_DESC_IDN_STRING = 0x5, + QUERY_DESC_IDN_RFU_1 = 0x6, + QUERY_DESC_IDN_GEOMETRY = 0x7, + QUERY_DESC_IDN_POWER = 0x8, + QUERY_DESC_IDN_MAX, +}; + +enum desc_header_offset { + QUERY_DESC_LENGTH_OFFSET = 0x00, + QUERY_DESC_DESC_TYPE_OFFSET = 0x01, +}; + +enum ufs_desc_max_size { + QUERY_DESC_DEVICE_MAX_SIZE = 0x1F, + QUERY_DESC_CONFIGURAION_MAX_SIZE = 0x90, + QUERY_DESC_UNIT_MAX_SIZE = 0x23, + QUERY_DESC_INTERCONNECT_MAX_SIZE = 0x06, + /* + * Max. 126 UNICODE characters (2 bytes per character) plus 2 bytes + * of descriptor header. + */ + QUERY_DESC_STRING_MAX_SIZE = 0xFE, + QUERY_DESC_GEOMETRY_MAZ_SIZE = 0x44, + QUERY_DESC_POWER_MAX_SIZE = 0x62, + QUERY_DESC_RFU_MAX_SIZE = 0x00, +}; + +/* Unit descriptor parameters offsets in bytes*/ +enum unit_desc_param { + UNIT_DESC_PARAM_LEN = 0x0, + UNIT_DESC_PARAM_TYPE = 0x1, + UNIT_DESC_PARAM_UNIT_INDEX = 0x2, + UNIT_DESC_PARAM_LU_ENABLE = 0x3, + UNIT_DESC_PARAM_BOOT_LUN_ID = 0x4, + UNIT_DESC_PARAM_LU_WR_PROTECT = 0x5, + UNIT_DESC_PARAM_LU_Q_DEPTH = 0x6, + UNIT_DESC_PARAM_MEM_TYPE = 0x8, + UNIT_DESC_PARAM_DATA_RELIABILITY = 0x9, + UNIT_DESC_PARAM_LOGICAL_BLK_SIZE = 0xA, + UNIT_DESC_PARAM_LOGICAL_BLK_COUNT = 0xB, + UNIT_DESC_PARAM_ERASE_BLK_SIZE = 0x13, + UNIT_DESC_PARAM_PROVISIONING_TYPE = 0x17, + UNIT_DESC_PARAM_PHY_MEM_RSRC_CNT = 0x18, + UNIT_DESC_PARAM_CTX_CAPABILITIES = 0x20, + UNIT_DESC_PARAM_LARGE_UNIT_SIZE_M1 = 0x22, +}; + +/* + * Logical Unit Write Protect + * 00h: LU not write protected + * 01h: LU write protected when fPowerOnWPEn =1 + * 02h: LU permanently write protected when fPermanentWPEn =1 + */ +enum ufs_lu_wp_type { + UFS_LU_NO_WP = 0x00, + UFS_LU_POWER_ON_WP = 0x01, + UFS_LU_PERM_WP = 0x02, +}; + +/* bActiveICCLevel parameter current units */ +enum { + UFSHCD_NANO_AMP = 0, + UFSHCD_MICRO_AMP = 1, + UFSHCD_MILI_AMP = 2, + UFSHCD_AMP = 3, +}; + +#define POWER_DESC_MAX_SIZE 0x62 +#define POWER_DESC_MAX_ACTV_ICC_LVLS 16 + +/* Attribute bActiveICCLevel parameter bit masks definitions */ +#define ATTR_ICC_LVL_UNIT_OFFSET 14 +#define ATTR_ICC_LVL_UNIT_MASK (0x3 << ATTR_ICC_LVL_UNIT_OFFSET) +#define ATTR_ICC_LVL_VALUE_MASK 0x3FF + +/* Power descriptor parameters offsets in bytes */ +enum power_desc_param_offset { + PWR_DESC_LEN = 0x0, + PWR_DESC_TYPE = 0x1, + PWR_DESC_ACTIVE_LVLS_VCC_0 = 0x2, + PWR_DESC_ACTIVE_LVLS_VCCQ_0 = 0x22, + PWR_DESC_ACTIVE_LVLS_VCCQ2_0 = 0x42, +}; + +/* Exception event mask values */ +enum { + MASK_EE_STATUS = 0xFFFF, + MASK_EE_URGENT_BKOPS = (1 << 2), +}; + +/* Background operation status */ +enum bkops_status { + BKOPS_STATUS_NO_OP = 0x0, + BKOPS_STATUS_NON_CRITICAL = 0x1, + BKOPS_STATUS_PERF_IMPACT = 0x2, + BKOPS_STATUS_CRITICAL = 0x3, + BKOPS_STATUS_MAX = BKOPS_STATUS_CRITICAL, +}; + +/* UTP QUERY Transaction Specific Fields OpCode */ +enum query_opcode { + UPIU_QUERY_OPCODE_NOP = 0x0, + UPIU_QUERY_OPCODE_READ_DESC = 0x1, + UPIU_QUERY_OPCODE_WRITE_DESC = 0x2, + UPIU_QUERY_OPCODE_READ_ATTR = 0x3, + UPIU_QUERY_OPCODE_WRITE_ATTR = 0x4, + UPIU_QUERY_OPCODE_READ_FLAG = 0x5, + UPIU_QUERY_OPCODE_SET_FLAG = 0x6, + UPIU_QUERY_OPCODE_CLEAR_FLAG = 0x7, + UPIU_QUERY_OPCODE_TOGGLE_FLAG = 0x8, +}; + +/* Query response result code */ +enum { + QUERY_RESULT_SUCCESS = 0x00, + QUERY_RESULT_NOT_READABLE = 0xF6, + QUERY_RESULT_NOT_WRITEABLE = 0xF7, + QUERY_RESULT_ALREADY_WRITTEN = 0xF8, + QUERY_RESULT_INVALID_LENGTH = 0xF9, + QUERY_RESULT_INVALID_VALUE = 0xFA, + QUERY_RESULT_INVALID_SELECTOR = 0xFB, + QUERY_RESULT_INVALID_INDEX = 0xFC, + QUERY_RESULT_INVALID_IDN = 0xFD, + QUERY_RESULT_INVALID_OPCODE = 0xFE, + QUERY_RESULT_GENERAL_FAILURE = 0xFF, +}; + +/* UTP Transfer Request Command Type (CT) */ +enum { + UPIU_COMMAND_SET_TYPE_SCSI = 0x0, + UPIU_COMMAND_SET_TYPE_UFS = 0x1, + UPIU_COMMAND_SET_TYPE_QUERY = 0x2, +}; + +/* UTP Transfer Request Command Offset */ +#define UPIU_COMMAND_TYPE_OFFSET 28 + +/* Offset of the response code in the UPIU header */ +#define UPIU_RSP_CODE_OFFSET 8 + +enum { + MASK_SCSI_STATUS = 0xFF, + MASK_TASK_RESPONSE = 0xFF00, + MASK_RSP_UPIU_RESULT = 0xFFFF, + MASK_QUERY_DATA_SEG_LEN = 0xFFFF, + MASK_RSP_UPIU_DATA_SEG_LEN = 0xFFFF, + MASK_RSP_EXCEPTION_EVENT = 0x10000, +}; + +/* Task management service response */ +enum { + UPIU_TASK_MANAGEMENT_FUNC_COMPL = 0x00, + UPIU_TASK_MANAGEMENT_FUNC_NOT_SUPPORTED = 0x04, + UPIU_TASK_MANAGEMENT_FUNC_SUCCEEDED = 0x08, + UPIU_TASK_MANAGEMENT_FUNC_FAILED = 0x05, + UPIU_INCORRECT_LOGICAL_UNIT_NO = 0x09, +}; + +/* UFS device power modes */ +enum ufs_dev_pwr_mode { + UFS_ACTIVE_PWR_MODE = 1, + UFS_SLEEP_PWR_MODE = 2, + UFS_POWERDOWN_PWR_MODE = 3, +}; + +/** + * struct utp_upiu_header - UPIU header structure + * @dword_0: UPIU header DW-0 + * @dword_1: UPIU header DW-1 + * @dword_2: UPIU header DW-2 + */ +struct utp_upiu_header { + __be32 dword_0; + __be32 dword_1; + __be32 dword_2; +}; + +/** + * struct utp_upiu_cmd - Command UPIU structure + * @data_transfer_len: Data Transfer Length DW-3 + * @cdb: Command Descriptor Block CDB DW-4 to DW-7 + */ +struct utp_upiu_cmd { + __be32 exp_data_transfer_len; + u8 cdb[MAX_CDB_SIZE]; +}; + +/** + * struct utp_upiu_query - upiu request buffer structure for + * query request. + * @opcode: command to perform B-0 + * @idn: a value that indicates the particular type of data B-1 + * @index: Index to further identify data B-2 + * @selector: Index to further identify data B-3 + * @reserved_osf: spec reserved field B-4,5 + * @length: number of descriptor bytes to read/write B-6,7 + * @value: Attribute value to be written DW-5 + * @reserved: spec reserved DW-6,7 + */ +struct utp_upiu_query { + u8 opcode; + u8 idn; + u8 index; + u8 selector; + __be16 reserved_osf; + __be16 length; + __be32 value; + __be32 reserved[2]; +}; + +/** + * struct utp_upiu_req - general upiu request structure + * @header:UPIU header structure DW-0 to DW-2 + * @sc: fields structure for scsi command DW-3 to DW-7 + * @qr: fields structure for query request DW-3 to DW-7 + */ +struct utp_upiu_req { + struct utp_upiu_header header; + union { + struct utp_upiu_cmd sc; + struct utp_upiu_query qr; + }; +}; + +/** + * struct utp_cmd_rsp - Response UPIU structure + * @residual_transfer_count: Residual transfer count DW-3 + * @reserved: Reserved double words DW-4 to DW-7 + * @sense_data_len: Sense data length DW-8 U16 + * @sense_data: Sense data field DW-8 to DW-12 + */ +struct utp_cmd_rsp { + __be32 residual_transfer_count; + __be32 reserved[4]; + __be16 sense_data_len; + u8 sense_data[18]; +}; + +/** + * struct utp_upiu_rsp - general upiu response structure + * @header: UPIU header structure DW-0 to DW-2 + * @sr: fields structure for scsi command DW-3 to DW-12 + * @qr: fields structure for query request DW-3 to DW-7 + */ +struct utp_upiu_rsp { + struct utp_upiu_header header; + union { + struct utp_cmd_rsp sr; + struct utp_upiu_query qr; + }; +}; + +/** + * struct utp_upiu_task_req - Task request UPIU structure + * @header - UPIU header structure DW0 to DW-2 + * @input_param1: Input parameter 1 DW-3 + * @input_param2: Input parameter 2 DW-4 + * @input_param3: Input parameter 3 DW-5 + * @reserved: Reserved double words DW-6 to DW-7 + */ +struct utp_upiu_task_req { + struct utp_upiu_header header; + __be32 input_param1; + __be32 input_param2; + __be32 input_param3; + __be32 reserved[2]; +}; + +/** + * struct utp_upiu_task_rsp - Task Management Response UPIU structure + * @header: UPIU header structure DW0-DW-2 + * @output_param1: Ouput parameter 1 DW3 + * @output_param2: Output parameter 2 DW4 + * @reserved: Reserved double words DW-5 to DW-7 + */ +struct utp_upiu_task_rsp { + struct utp_upiu_header header; + __be32 output_param1; + __be32 output_param2; + __be32 reserved[3]; +}; + +/** + * struct ufs_query_req - parameters for building a query request + * @query_func: UPIU header query function + * @upiu_req: the query request data + */ +struct ufs_query_req { + u8 query_func; + struct utp_upiu_query upiu_req; +}; + +/** + * struct ufs_query_resp - UPIU QUERY + * @response: device response code + * @upiu_res: query response data + */ +struct ufs_query_res { + u8 response; + struct utp_upiu_query upiu_res; +}; + +#define UFS_VREG_VCC_MIN_UV 2700000 /* uV */ +#define UFS_VREG_VCC_MAX_UV 3600000 /* uV */ +#define UFS_VREG_VCC_1P8_MIN_UV 1700000 /* uV */ +#define UFS_VREG_VCC_1P8_MAX_UV 1950000 /* uV */ +#define UFS_VREG_VCCQ_MIN_UV 1100000 /* uV */ +#define UFS_VREG_VCCQ_MAX_UV 1300000 /* uV */ +#define UFS_VREG_VCCQ2_MIN_UV 1650000 /* uV */ +#define UFS_VREG_VCCQ2_MAX_UV 1950000 /* uV */ + +/* + * VCCQ & VCCQ2 current requirement when UFS device is in sleep state + * and link is in Hibern8 state. + */ +#define UFS_VREG_LPM_LOAD_UA 1000 /* uA */ + +struct ufs_vreg { + struct regulator *reg; + const char *name; + bool enabled; + int min_uV; + int max_uV; + int min_uA; + int max_uA; +}; + +struct ufs_vreg_info { + struct ufs_vreg *vcc; + struct ufs_vreg *vccq; + struct ufs_vreg *vccq2; + struct ufs_vreg *vdd_hba; +}; + +struct ufs_dev_info { + bool f_power_on_wp_en; + /* Keeps information if any of the LU is power on write protected */ + bool is_lu_power_on_wp; +}; + +#endif /* End of Header */ diff --git a/include/linux/scsi/ufs/ufshcd.h b/include/linux/scsi/ufs/ufshcd.h new file mode 100644 index 0000000..51304f7 --- /dev/null +++ b/include/linux/scsi/ufs/ufshcd.h @@ -0,0 +1,635 @@ +/* + * Universal Flash Storage Host controller driver + * + * This code is based on drivers/scsi/ufs/ufshcd.h + * Copyright (C) 2011-2013 Samsung India Software Operations + * + * Authors: + * Santosh Yaraganavi <santosh.sy@xxxxxxxxxxx> + * Vinayak Holikatti <h.vinayak@xxxxxxxxxxx> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * See the COPYING file in the top-level directory or visit + * <http://www.gnu.org/licenses/gpl-2.0.html> + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * This program is provided "AS IS" and "WITH ALL FAULTS" and + * without warranty of any kind. You are solely responsible for + * determining the appropriateness of using and distributing + * the program and assume all risks associated with your exercise + * of rights with respect to the program, including but not limited + * to infringement of third party rights, the risks and costs of + * program errors, damage to or loss of data, programs or equipment, + * and unavailability or interruption of operations. Under no + * circumstances will the contributor of this Program be liable for + * any damages of any kind arising from your use or distribution of + * this program. + */ + +#ifndef _UFSHCD_H +#define _UFSHCD_H + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/spinlock.h> +#include <linux/workqueue.h> +#include <linux/errno.h> +#include <linux/types.h> +#include <linux/wait.h> +#include <linux/bitops.h> +#include <linux/pm_runtime.h> +#include <linux/clk.h> +#include <linux/completion.h> +#include <linux/regulator/consumer.h> + +#include <asm/irq.h> +#include <asm/byteorder.h> +#include <scsi/scsi.h> +#include <scsi/scsi_cmnd.h> +#include <scsi/scsi_host.h> +#include <scsi/scsi_tcq.h> +#include <scsi/scsi_dbg.h> +#include <scsi/scsi_eh.h> + +#include "ufs.h" + +#define UFSHCD "ufshcd" +#define UFSHCD_DRIVER_VERSION "0.2" + +struct ufs_hba; + +/** + * readl_poll_timeout - Periodically poll an address until a condition is met or a timeout occurs + * @addr: Address to poll + * @val: Variable to read the value into + * @cond: Break condition (usually involving @val) + * @sleep_us: Maximum time to sleep between reads in us (0 tight-loops) + * @timeout_us: Timeout in us, 0 means never timeout + * + * Returns 0 on success and -ETIMEDOUT upon a timeout. In either + * case, the last read value at @addr is stored in @val. Must not + * be called from atomic context if sleep_us or timeout_us are used. + */ +#define readl_poll_timeout(addr, val, cond, sleep_us, timeout_us) \ +({ \ + ktime_t timeout = ktime_add_us(ktime_get(), timeout_us); \ + might_sleep_if(timeout_us); \ + for (;;) { \ + (val) = readl(addr); \ + if (cond) \ + break; \ + if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) { \ + (val) = readl(addr); \ + break; \ + } \ + if (sleep_us) \ + usleep_range(DIV_ROUND_UP(sleep_us, 4), sleep_us); \ + } \ + (cond) ? 0 : -ETIMEDOUT; \ +}) + +enum dev_cmd_type { + DEV_CMD_TYPE_NOP = 0x0, + DEV_CMD_TYPE_QUERY = 0x1, +}; + +/** + * struct uic_command - UIC command structure + * @command: UIC command + * @argument1: UIC command argument 1 + * @argument2: UIC command argument 2 + * @argument3: UIC command argument 3 + * @cmd_active: Indicate if UIC command is outstanding + * @result: UIC command result + * @done: UIC command completion + */ +struct uic_command { + u32 command; + u32 argument1; + u32 argument2; + u32 argument3; + int cmd_active; + int result; + struct completion done; +}; + +/* Used to differentiate the power management options */ +enum ufs_pm_op { + UFS_RUNTIME_PM, + UFS_SYSTEM_PM, + UFS_SHUTDOWN_PM, +}; + +#define ufshcd_is_runtime_pm(op) ((op) == UFS_RUNTIME_PM) +#define ufshcd_is_system_pm(op) ((op) == UFS_SYSTEM_PM) +#define ufshcd_is_shutdown_pm(op) ((op) == UFS_SHUTDOWN_PM) + +/* Host <-> Device UniPro Link state */ +enum uic_link_state { + UIC_LINK_OFF_STATE = 0, /* Link powered down or disabled */ + UIC_LINK_ACTIVE_STATE = 1, /* Link is in Fast/Slow/Sleep state */ + UIC_LINK_HIBERN8_STATE = 2, /* Link is in Hibernate state */ +}; + +#define ufshcd_is_link_off(hba) ((hba)->uic_link_state == UIC_LINK_OFF_STATE) +#define ufshcd_is_link_active(hba) ((hba)->uic_link_state == \ + UIC_LINK_ACTIVE_STATE) +#define ufshcd_is_link_hibern8(hba) ((hba)->uic_link_state == \ + UIC_LINK_HIBERN8_STATE) +#define ufshcd_set_link_off(hba) ((hba)->uic_link_state = UIC_LINK_OFF_STATE) +#define ufshcd_set_link_active(hba) ((hba)->uic_link_state = \ + UIC_LINK_ACTIVE_STATE) +#define ufshcd_set_link_hibern8(hba) ((hba)->uic_link_state = \ + UIC_LINK_HIBERN8_STATE) + +/* + * UFS Power management levels. + * Each level is in increasing order of power savings. + */ +enum ufs_pm_level { + UFS_PM_LVL_0, /* UFS_ACTIVE_PWR_MODE, UIC_LINK_ACTIVE_STATE */ + UFS_PM_LVL_1, /* UFS_ACTIVE_PWR_MODE, UIC_LINK_HIBERN8_STATE */ + UFS_PM_LVL_2, /* UFS_SLEEP_PWR_MODE, UIC_LINK_ACTIVE_STATE */ + UFS_PM_LVL_3, /* UFS_SLEEP_PWR_MODE, UIC_LINK_HIBERN8_STATE */ + UFS_PM_LVL_4, /* UFS_POWERDOWN_PWR_MODE, UIC_LINK_HIBERN8_STATE */ + UFS_PM_LVL_5, /* UFS_POWERDOWN_PWR_MODE, UIC_LINK_OFF_STATE */ + UFS_PM_LVL_MAX +}; + +struct ufs_pm_lvl_states { + enum ufs_dev_pwr_mode dev_state; + enum uic_link_state link_state; +}; + +/** + * struct ufshcd_lrb - local reference block + * @utr_descriptor_ptr: UTRD address of the command + * @ucd_req_ptr: UCD address of the command + * @ucd_rsp_ptr: Response UPIU address for this command + * @ucd_prdt_ptr: PRDT address of the command + * @cmd: pointer to SCSI command + * @sense_buffer: pointer to sense buffer address of the SCSI command + * @sense_bufflen: Length of the sense buffer + * @scsi_status: SCSI status of the command + * @command_type: SCSI, UFS, Query. + * @task_tag: Task tag of the command + * @lun: LUN of the command + * @intr_cmd: Interrupt command (doesn't participate in interrupt aggregation) + */ +struct ufshcd_lrb { + struct utp_transfer_req_desc *utr_descriptor_ptr; + struct utp_upiu_req *ucd_req_ptr; + struct utp_upiu_rsp *ucd_rsp_ptr; + struct ufshcd_sg_entry *ucd_prdt_ptr; + + struct scsi_cmnd *cmd; + u8 *sense_buffer; + unsigned int sense_bufflen; + int scsi_status; + + int command_type; + int task_tag; + u8 lun; /* UPIU LUN id field is only 8-bit wide */ + bool intr_cmd; +}; + +/** + * struct ufs_query - holds relevent data structures for query request + * @request: request upiu and function + * @descriptor: buffer for sending/receiving descriptor + * @response: response upiu and response + */ +struct ufs_query { + struct ufs_query_req request; + u8 *descriptor; + struct ufs_query_res response; +}; + +/** + * struct ufs_dev_cmd - all assosiated fields with device management commands + * @type: device management command type - Query, NOP OUT + * @lock: lock to allow one command at a time + * @complete: internal commands completion + * @tag_wq: wait queue until free command slot is available + */ +struct ufs_dev_cmd { + enum dev_cmd_type type; + struct mutex lock; + struct completion *complete; + wait_queue_head_t tag_wq; + struct ufs_query query; +}; + +/** + * struct ufs_clk_info - UFS clock related info + * @list: list headed by hba->clk_list_head + * @clk: clock node + * @name: clock name + * @max_freq: maximum frequency supported by the clock + * @min_freq: min frequency that can be used for clock scaling + * @curr_freq: indicates the current frequency that it is set to + * @enabled: variable to check against multiple enable/disable + */ +struct ufs_clk_info { + struct list_head list; + struct clk *clk; + const char *name; + u32 max_freq; + u32 min_freq; + u32 curr_freq; + bool enabled; +}; + +#define PRE_CHANGE 0 +#define POST_CHANGE 1 + +struct ufs_pa_layer_attr { + u32 gear_rx; + u32 gear_tx; + u32 lane_rx; + u32 lane_tx; + u32 pwr_rx; + u32 pwr_tx; + u32 hs_rate; +}; + +struct ufs_pwr_mode_info { + bool is_valid; + struct ufs_pa_layer_attr info; +}; + +/** + * struct ufs_hba_variant_ops - variant specific callbacks + * @name: variant name + * @init: called when the driver is initialized + * @exit: called to cleanup everything done in init + * @clk_scale_notify: notifies that clks are scaled up/down + * @setup_clocks: called before touching any of the controller registers + * @setup_regulators: called before accessing the host controller + * @hce_enable_notify: called before and after HCE enable bit is set to allow + * variant specific Uni-Pro initialization. + * @link_startup_notify: called before and after Link startup is carried out + * to allow variant specific Uni-Pro initialization. + * @pwr_change_notify: called before and after a power mode change + * is carried out to allow vendor spesific capabilities + * to be set. + * @suspend: called during host controller PM callback + * @resume: called during host controller PM callback + */ +struct ufs_hba_variant_ops { + const char *name; + int (*init)(struct ufs_hba *); + void (*exit)(struct ufs_hba *); + void (*clk_scale_notify)(struct ufs_hba *); + int (*setup_clocks)(struct ufs_hba *, bool); + int (*setup_regulators)(struct ufs_hba *, bool); + int (*hce_enable_notify)(struct ufs_hba *, bool); + int (*link_startup_notify)(struct ufs_hba *, bool); + int (*pwr_change_notify)(struct ufs_hba *, + bool, struct ufs_pa_layer_attr *, + struct ufs_pa_layer_attr *); + int (*suspend)(struct ufs_hba *, enum ufs_pm_op); + int (*resume)(struct ufs_hba *, enum ufs_pm_op); +}; + +/* clock gating state */ +enum clk_gating_state { + CLKS_OFF, + CLKS_ON, + REQ_CLKS_OFF, + REQ_CLKS_ON, +}; + +/** + * struct ufs_clk_gating - UFS clock gating related info + * @gate_work: worker to turn off clocks after some delay as specified in + * delay_ms + * @ungate_work: worker to turn on clocks that will be used in case of + * interrupt context + * @state: the current clocks state + * @delay_ms: gating delay in ms + * @is_suspended: clk gating is suspended when set to 1 which can be used + * during suspend/resume + * @delay_attr: sysfs attribute to control delay_attr + * @active_reqs: number of requests that are pending and should be waited for + * completion before gating clocks. + */ +struct ufs_clk_gating { + struct delayed_work gate_work; + struct work_struct ungate_work; + enum clk_gating_state state; + unsigned long delay_ms; + bool is_suspended; + struct device_attribute delay_attr; + int active_reqs; +}; + +struct ufs_clk_scaling { + ktime_t busy_start_t; + bool is_busy_started; + unsigned long tot_busy_t; + unsigned long window_start_t; +}; + +/** + * struct ufs_init_prefetch - contains data that is pre-fetched once during + * initialization + * @icc_level: icc level which was read during initialization + */ +struct ufs_init_prefetch { + u32 icc_level; +}; + +/** + * struct ufs_hba - per adapter private structure + * @mmio_base: UFSHCI base register address + * @ucdl_base_addr: UFS Command Descriptor base address + * @utrdl_base_addr: UTP Transfer Request Descriptor base address + * @utmrdl_base_addr: UTP Task Management Descriptor base address + * @ucdl_dma_addr: UFS Command Descriptor DMA address + * @utrdl_dma_addr: UTRDL DMA address + * @utmrdl_dma_addr: UTMRDL DMA address + * @host: Scsi_Host instance of the driver + * @dev: device handle + * @lrb: local reference block + * @lrb_in_use: lrb in use + * @outstanding_tasks: Bits representing outstanding task requests + * @outstanding_reqs: Bits representing outstanding transfer requests + * @capabilities: UFS Controller Capabilities + * @nutrs: Transfer Request Queue depth supported by controller + * @nutmrs: Task Management Queue depth supported by controller + * @ufs_version: UFS Version to which controller complies + * @vops: pointer to variant specific operations + * @priv: pointer to variant specific private data + * @irq: Irq number of the controller + * @active_uic_cmd: handle of active UIC command + * @uic_cmd_mutex: mutex for uic command + * @tm_wq: wait queue for task management + * @tm_tag_wq: wait queue for free task management slots + * @tm_slots_in_use: bit map of task management request slots in use + * @pwr_done: completion for power mode change + * @tm_condition: condition variable for task management + * @ufshcd_state: UFSHCD states + * @eh_flags: Error handling flags + * @intr_mask: Interrupt Mask Bits + * @ee_ctrl_mask: Exception event control mask + * @is_powered: flag to check if HBA is powered + * @is_init_prefetch: flag to check if data was pre-fetched in initialization + * @init_prefetch_data: data pre-fetched during initialization + * @eh_work: Worker to handle UFS errors that require s/w attention + * @eeh_work: Worker to handle exception events + * @errors: HBA errors + * @uic_error: UFS interconnect layer error status + * @saved_err: sticky error mask + * @saved_uic_err: sticky UIC error mask + * @dev_cmd: ufs device management command information + * @auto_bkops_enabled: to track whether bkops is enabled in device + * @vreg_info: UFS device voltage regulator information + * @clk_list_head: UFS host controller clocks list node head + * @pwr_info: holds current power mode + * @max_pwr_info: keeps the device max valid pwm + */ +struct ufs_hba { + void __iomem *mmio_base; + + /* Virtual memory reference */ + struct utp_transfer_cmd_desc *ucdl_base_addr; + struct utp_transfer_req_desc *utrdl_base_addr; + struct utp_task_req_desc *utmrdl_base_addr; + + /* DMA memory reference */ + dma_addr_t ucdl_dma_addr; + dma_addr_t utrdl_dma_addr; + dma_addr_t utmrdl_dma_addr; + + struct Scsi_Host *host; + struct device *dev; + /* + * This field is to keep a reference to "scsi_device" corresponding to + * "UFS device" W-LU. + */ + struct scsi_device *sdev_ufs_device; + enum ufs_dev_pwr_mode curr_dev_pwr_mode; + enum uic_link_state uic_link_state; + /* Desired UFS power management level during runtime PM */ + enum ufs_pm_level rpm_lvl; + /* Desired UFS power management level during system PM */ + enum ufs_pm_level spm_lvl; + int pm_op_in_progress; + + struct ufshcd_lrb *lrb; + unsigned long lrb_in_use; + + unsigned long outstanding_tasks; + unsigned long outstanding_reqs; + + u32 capabilities; + int nutrs; + int nutmrs; + u32 ufs_version; + struct ufs_hba_variant_ops *vops; + void *priv; + unsigned int irq; + bool is_irq_enabled; + + /* Interrupt aggregation support is broken */ + #define UFSHCD_QUIRK_BROKEN_INTR_AGGR UFS_BIT(0) + + /* + * delay before each dme command is required as the unipro + * layer has shown instabilities + */ + #define UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS UFS_BIT(1) + + /* + * If UFS host controller is having issue in processing LCC (Line + * Control Command) coming from device then enable this quirk. + * When this quirk is enabled, host controller driver should disable + * the LCC transmission on UFS device (by clearing TX_LCC_ENABLE + * attribute of device to 0). + */ + #define UFSHCD_QUIRK_BROKEN_LCC UFS_BIT(2) + + /* + * The attribute PA_RXHSUNTERMCAP specifies whether or not the + * inbound Link supports unterminated line in HS mode. Setting this + * attribute to 1 fixes moving to HS gear. + */ + #define UFSHCD_QUIRK_BROKEN_PA_RXHSUNTERMCAP UFS_BIT(3) + + unsigned int quirks; /* Deviations from standard UFSHCI spec. */ + + wait_queue_head_t tm_wq; + wait_queue_head_t tm_tag_wq; + unsigned long tm_condition; + unsigned long tm_slots_in_use; + + struct uic_command *active_uic_cmd; + struct mutex uic_cmd_mutex; + struct completion *uic_async_done; + + u32 ufshcd_state; + u32 eh_flags; + u32 intr_mask; + u16 ee_ctrl_mask; + bool is_powered; + bool is_init_prefetch; + struct ufs_init_prefetch init_prefetch_data; + + /* Work Queues */ + struct work_struct eh_work; + struct work_struct eeh_work; + + /* HBA Errors */ + u32 errors; + u32 uic_error; + u32 saved_err; + u32 saved_uic_err; + + /* Device management request data */ + struct ufs_dev_cmd dev_cmd; + + /* Keeps information of the UFS device connected to this host */ + struct ufs_dev_info dev_info; + bool auto_bkops_enabled; + struct ufs_vreg_info vreg_info; + struct list_head clk_list_head; + + bool wlun_dev_clr_ua; + + struct ufs_pa_layer_attr pwr_info; + struct ufs_pwr_mode_info max_pwr_info; + + struct ufs_clk_gating clk_gating; + /* Control to enable/disable host capabilities */ + u32 caps; + /* Allow dynamic clk gating */ +#define UFSHCD_CAP_CLK_GATING (1 << 0) + /* Allow hiberb8 with clk gating */ +#define UFSHCD_CAP_HIBERN8_WITH_CLK_GATING (1 << 1) + /* Allow dynamic clk scaling */ +#define UFSHCD_CAP_CLK_SCALING (1 << 2) + /* Allow auto bkops to enabled during runtime suspend */ +#define UFSHCD_CAP_AUTO_BKOPS_SUSPEND (1 << 3) + + struct devfreq *devfreq; + struct ufs_clk_scaling clk_scaling; + bool is_sys_suspended; +}; + +/* Returns true if clocks can be gated. Otherwise false */ +static inline bool ufshcd_is_clkgating_allowed(struct ufs_hba *hba) +{ + return hba->caps & UFSHCD_CAP_CLK_GATING; +} +static inline bool ufshcd_can_hibern8_during_gating(struct ufs_hba *hba) +{ + return hba->caps & UFSHCD_CAP_HIBERN8_WITH_CLK_GATING; +} +static inline int ufshcd_is_clkscaling_enabled(struct ufs_hba *hba) +{ + return hba->caps & UFSHCD_CAP_CLK_SCALING; +} +static inline bool ufshcd_can_autobkops_during_suspend(struct ufs_hba *hba) +{ + return hba->caps & UFSHCD_CAP_AUTO_BKOPS_SUSPEND; +} + +#define ufshcd_writel(hba, val, reg) \ + writel((val), (hba)->mmio_base + (reg)) +#define ufshcd_readl(hba, reg) \ + readl((hba)->mmio_base + (reg)) + +/** + * ufshcd_rmwl - read modify write into a register + * @hba - per adapter instance + * @mask - mask to apply on read value + * @val - actual value to write + * @reg - register address + */ +static inline void ufshcd_rmwl(struct ufs_hba *hba, u32 mask, u32 val, u32 reg) +{ + u32 tmp; + + tmp = ufshcd_readl(hba, reg); + tmp &= ~mask; + tmp |= (val & mask); + ufshcd_writel(hba, tmp, reg); +} + +int ufshcd_alloc_host(struct device *, struct ufs_hba **); +int ufshcd_init(struct ufs_hba * , void __iomem * , unsigned int); +void ufshcd_remove(struct ufs_hba *); + +extern int ufshcd_runtime_suspend(struct ufs_hba *hba); +extern int ufshcd_runtime_resume(struct ufs_hba *hba); +extern int ufshcd_runtime_idle(struct ufs_hba *hba); +extern int ufshcd_system_suspend(struct ufs_hba *hba); +extern int ufshcd_system_resume(struct ufs_hba *hba); +extern int ufshcd_shutdown(struct ufs_hba *hba); +extern int ufshcd_dme_set_attr(struct ufs_hba *hba, u32 attr_sel, + u8 attr_set, u32 mib_val, u8 peer); +extern int ufshcd_dme_get_attr(struct ufs_hba *hba, u32 attr_sel, + u32 *mib_val, u8 peer); + +/* UIC command interfaces for DME primitives */ +#define DME_LOCAL 0 +#define DME_PEER 1 +#define ATTR_SET_NOR 0 /* NORMAL */ +#define ATTR_SET_ST 1 /* STATIC */ + +static inline int ufshcd_dme_set(struct ufs_hba *hba, u32 attr_sel, + u32 mib_val) +{ + return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR, + mib_val, DME_LOCAL); +} + +static inline int ufshcd_dme_st_set(struct ufs_hba *hba, u32 attr_sel, + u32 mib_val) +{ + return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_ST, + mib_val, DME_LOCAL); +} + +static inline int ufshcd_dme_peer_set(struct ufs_hba *hba, u32 attr_sel, + u32 mib_val) +{ + return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_NOR, + mib_val, DME_PEER); +} + +static inline int ufshcd_dme_peer_st_set(struct ufs_hba *hba, u32 attr_sel, + u32 mib_val) +{ + return ufshcd_dme_set_attr(hba, attr_sel, ATTR_SET_ST, + mib_val, DME_PEER); +} + +static inline int ufshcd_dme_get(struct ufs_hba *hba, + u32 attr_sel, u32 *mib_val) +{ + return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_LOCAL); +} + +static inline int ufshcd_dme_peer_get(struct ufs_hba *hba, + u32 attr_sel, u32 *mib_val) +{ + return ufshcd_dme_get_attr(hba, attr_sel, mib_val, DME_PEER); +} + +int ufshcd_hold(struct ufs_hba *hba, bool async); +void ufshcd_release(struct ufs_hba *hba); +#endif /* End of Header */ diff --git a/include/linux/scsi/ufs/unipro.h b/include/linux/scsi/ufs/unipro.h new file mode 100644 index 0000000..3fc3e21 --- /dev/null +++ b/include/linux/scsi/ufs/unipro.h @@ -0,0 +1,207 @@ +/* + * drivers/scsi/ufs/unipro.h + * + * Copyright (C) 2013 Samsung Electronics Co., Ltd. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef _UNIPRO_H_ +#define _UNIPRO_H_ + +/* + * M-TX Configuration Attributes + */ +#define TX_MODE 0x0021 +#define TX_HSRATE_SERIES 0x0022 +#define TX_HSGEAR 0x0023 +#define TX_PWMGEAR 0x0024 +#define TX_AMPLITUDE 0x0025 +#define TX_HS_SLEWRATE 0x0026 +#define TX_SYNC_SOURCE 0x0027 +#define TX_HS_SYNC_LENGTH 0x0028 +#define TX_HS_PREPARE_LENGTH 0x0029 +#define TX_LS_PREPARE_LENGTH 0x002A +#define TX_HIBERN8_CONTROL 0x002B +#define TX_LCC_ENABLE 0x002C +#define TX_PWM_BURST_CLOSURE_EXTENSION 0x002D +#define TX_BYPASS_8B10B_ENABLE 0x002E +#define TX_DRIVER_POLARITY 0x002F +#define TX_HS_UNTERMINATED_LINE_DRIVE_ENABLE 0x0030 +#define TX_LS_TERMINATED_LINE_DRIVE_ENABLE 0x0031 +#define TX_LCC_SEQUENCER 0x0032 +#define TX_MIN_ACTIVATETIME 0x0033 +#define TX_PWM_G6_G7_SYNC_LENGTH 0x0034 + +/* + * M-RX Configuration Attributes + */ +#define RX_MODE 0x00A1 +#define RX_HSRATE_SERIES 0x00A2 +#define RX_HSGEAR 0x00A3 +#define RX_PWMGEAR 0x00A4 +#define RX_LS_TERMINATED_ENABLE 0x00A5 +#define RX_HS_UNTERMINATED_ENABLE 0x00A6 +#define RX_ENTER_HIBERN8 0x00A7 +#define RX_BYPASS_8B10B_ENABLE 0x00A8 +#define RX_TERMINATION_FORCE_ENABLE 0x0089 + +#define is_mphy_tx_attr(attr) (attr < RX_MODE) +/* + * PHY Adpater attributes + */ +#define PA_ACTIVETXDATALANES 0x1560 +#define PA_ACTIVERXDATALANES 0x1580 +#define PA_TXTRAILINGCLOCKS 0x1564 +#define PA_PHY_TYPE 0x1500 +#define PA_AVAILTXDATALANES 0x1520 +#define PA_AVAILRXDATALANES 0x1540 +#define PA_MINRXTRAILINGCLOCKS 0x1543 +#define PA_TXPWRSTATUS 0x1567 +#define PA_RXPWRSTATUS 0x1582 +#define PA_TXFORCECLOCK 0x1562 +#define PA_TXPWRMODE 0x1563 +#define PA_LEGACYDPHYESCDL 0x1570 +#define PA_MAXTXSPEEDFAST 0x1521 +#define PA_MAXTXSPEEDSLOW 0x1522 +#define PA_MAXRXSPEEDFAST 0x1541 +#define PA_MAXRXSPEEDSLOW 0x1542 +#define PA_TXLINKSTARTUPHS 0x1544 +#define PA_TXSPEEDFAST 0x1565 +#define PA_TXSPEEDSLOW 0x1566 +#define PA_REMOTEVERINFO 0x15A0 +#define PA_TXGEAR 0x1568 +#define PA_TXTERMINATION 0x1569 +#define PA_HSSERIES 0x156A +#define PA_PWRMODE 0x1571 +#define PA_RXGEAR 0x1583 +#define PA_RXTERMINATION 0x1584 +#define PA_MAXRXPWMGEAR 0x1586 +#define PA_MAXRXHSGEAR 0x1587 +#define PA_RXHSUNTERMCAP 0x15A5 +#define PA_RXLSTERMCAP 0x15A6 +#define PA_PACPREQTIMEOUT 0x1590 +#define PA_PACPREQEOBTIMEOUT 0x1591 +#define PA_HIBERN8TIME 0x15A7 +#define PA_LOCALVERINFO 0x15A9 +#define PA_TACTIVATE 0x15A8 +#define PA_PACPFRAMECOUNT 0x15C0 +#define PA_PACPERRORCOUNT 0x15C1 +#define PA_PHYTESTCONTROL 0x15C2 +#define PA_PWRMODEUSERDATA0 0x15B0 +#define PA_PWRMODEUSERDATA1 0x15B1 +#define PA_PWRMODEUSERDATA2 0x15B2 +#define PA_PWRMODEUSERDATA3 0x15B3 +#define PA_PWRMODEUSERDATA4 0x15B4 +#define PA_PWRMODEUSERDATA5 0x15B5 +#define PA_PWRMODEUSERDATA6 0x15B6 +#define PA_PWRMODEUSERDATA7 0x15B7 +#define PA_PWRMODEUSERDATA8 0x15B8 +#define PA_PWRMODEUSERDATA9 0x15B9 +#define PA_PWRMODEUSERDATA10 0x15BA +#define PA_PWRMODEUSERDATA11 0x15BB +#define PA_CONNECTEDTXDATALANES 0x1561 +#define PA_CONNECTEDRXDATALANES 0x1581 +#define PA_LOGICALLANEMAP 0x15A1 +#define PA_SLEEPNOCONFIGTIME 0x15A2 +#define PA_STALLNOCONFIGTIME 0x15A3 +#define PA_SAVECONFIGTIME 0x15A4 + +/* PA power modes */ +enum { + FAST_MODE = 1, + SLOW_MODE = 2, + FASTAUTO_MODE = 4, + SLOWAUTO_MODE = 5, + UNCHANGED = 7, +}; + +/* PA TX/RX Frequency Series */ +enum { + PA_HS_MODE_A = 1, + PA_HS_MODE_B = 2, +}; + +enum ufs_pwm_gear_tag { + UFS_PWM_DONT_CHANGE, /* Don't change Gear */ + UFS_PWM_G1, /* PWM Gear 1 (default for reset) */ + UFS_PWM_G2, /* PWM Gear 2 */ + UFS_PWM_G3, /* PWM Gear 3 */ + UFS_PWM_G4, /* PWM Gear 4 */ + UFS_PWM_G5, /* PWM Gear 5 */ + UFS_PWM_G6, /* PWM Gear 6 */ + UFS_PWM_G7, /* PWM Gear 7 */ +}; + +enum ufs_hs_gear_tag { + UFS_HS_DONT_CHANGE, /* Don't change Gear */ + UFS_HS_G1, /* HS Gear 1 (default for reset) */ + UFS_HS_G2, /* HS Gear 2 */ + UFS_HS_G3, /* HS Gear 3 */ +}; + +/* + * Data Link Layer Attributes + */ +#define DL_TC0TXFCTHRESHOLD 0x2040 +#define DL_FC0PROTTIMEOUTVAL 0x2041 +#define DL_TC0REPLAYTIMEOUTVAL 0x2042 +#define DL_AFC0REQTIMEOUTVAL 0x2043 +#define DL_AFC0CREDITTHRESHOLD 0x2044 +#define DL_TC0OUTACKTHRESHOLD 0x2045 +#define DL_TC1TXFCTHRESHOLD 0x2060 +#define DL_FC1PROTTIMEOUTVAL 0x2061 +#define DL_TC1REPLAYTIMEOUTVAL 0x2062 +#define DL_AFC1REQTIMEOUTVAL 0x2063 +#define DL_AFC1CREDITTHRESHOLD 0x2064 +#define DL_TC1OUTACKTHRESHOLD 0x2065 +#define DL_TXPREEMPTIONCAP 0x2000 +#define DL_TC0TXMAXSDUSIZE 0x2001 +#define DL_TC0RXINITCREDITVAL 0x2002 +#define DL_TC0TXBUFFERSIZE 0x2005 +#define DL_PEERTC0PRESENT 0x2046 +#define DL_PEERTC0RXINITCREVAL 0x2047 +#define DL_TC1TXMAXSDUSIZE 0x2003 +#define DL_TC1RXINITCREDITVAL 0x2004 +#define DL_TC1TXBUFFERSIZE 0x2006 +#define DL_PEERTC1PRESENT 0x2066 +#define DL_PEERTC1RXINITCREVAL 0x2067 + +/* + * Network Layer Attributes + */ +#define N_DEVICEID 0x3000 +#define N_DEVICEID_VALID 0x3001 +#define N_TC0TXMAXSDUSIZE 0x3020 +#define N_TC1TXMAXSDUSIZE 0x3021 + +/* + * Transport Layer Attributes + */ +#define T_NUMCPORTS 0x4000 +#define T_NUMTESTFEATURES 0x4001 +#define T_CONNECTIONSTATE 0x4020 +#define T_PEERDEVICEID 0x4021 +#define T_PEERCPORTID 0x4022 +#define T_TRAFFICCLASS 0x4023 +#define T_PROTOCOLID 0x4024 +#define T_CPORTFLAGS 0x4025 +#define T_TXTOKENVALUE 0x4026 +#define T_RXTOKENVALUE 0x4027 +#define T_LOCALBUFFERSPACE 0x4028 +#define T_PEERBUFFERSPACE 0x4029 +#define T_CREDITSTOSEND 0x402A +#define T_CPORTMODE 0x402B +#define T_TC0TXMAXSDUSIZE 0x4060 +#define T_TC1TXMAXSDUSIZE 0x4061 + +/* Boolean attribute values */ +enum { + FALSE = 0, + TRUE, +}; + +#endif /* _UNIPRO_H_ */ -- 1.8.5.2 -- QUALCOMM ISRAEL, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation -- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
