It has not been possible to set CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO,
CONFIG_SCSI_NCR53C8XX_DISABLE_MPARITY_CHECK, and
CONFIG_SCSI_NCR53C8XX_DISABLE_PARITY_CHECK through the configuration
system since v2.1.20. Remove these ancient macros.
To enable (or disable) the functionality they covered one should edit a
header file and set related preprocessor macros. Since this is actually
a documented feature those related macros remain available.
Signed-off-by: Paul Bolle <pebolle@xxxxxxxxxx>
---
Untested.
Note that the documentation still contains
insmod ncr53c8xx
Besides insmod being outdated, the modules that use ncr53c8xx's code
appear to be NCR_Q720_mod.ko and zalon7xx.ko. So the documentation needs
probably to be updated to reflect this.
Documentation/scsi/ncr53c8xx.txt | 5 -----
drivers/scsi/ncr53c8xx.h | 12 ------------
2 files changed, 17 deletions(-)
diff --git a/Documentation/scsi/ncr53c8xx.txt b/Documentation/scsi/ncr53c8xx.txt
index 49c7b723225b..df4a1b97e659 100644
--- a/Documentation/scsi/ncr53c8xx.txt
+++ b/Documentation/scsi/ncr53c8xx.txt
@@ -580,11 +580,6 @@ CONFIG_SCSI_NCR53C8XX_SYNC (default answer: 5)
This frequency can be changed later with the "setsync" control command.
0 means "asynchronous data transfers".
-CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO (default answer: n)
- Force synchronous negotiation for all SCSI-2 devices.
- Some SCSI-2 devices do not report this feature in byte 7 of inquiry
- response but do support it properly (TAMARACK scanners for example).
-
CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT (default and only reasonable answer: n)
If you suspect a device of yours does not properly support disconnections,
you can answer "y". Then, all SCSI devices will never disconnect the bus
diff --git a/drivers/scsi/ncr53c8xx.h b/drivers/scsi/ncr53c8xx.h
index e34ec5a2ea5e..8043635982bc 100644
--- a/drivers/scsi/ncr53c8xx.h
+++ b/drivers/scsi/ncr53c8xx.h
@@ -148,29 +148,17 @@
/*
* Force synchronous negotiation for all targets
*/
-#ifdef CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO
-#define SCSI_NCR_SETUP_FORCE_SYNC_NEGO (1)
-#else
#define SCSI_NCR_SETUP_FORCE_SYNC_NEGO (0)
-#endif
/*
* Disable master parity checking (flawed hardwares need that)
*/
-#ifdef CONFIG_SCSI_NCR53C8XX_DISABLE_MPARITY_CHECK
-#define SCSI_NCR_SETUP_MASTER_PARITY (0)
-#else
#define SCSI_NCR_SETUP_MASTER_PARITY (1)
-#endif
/*
* Disable scsi parity checking (flawed devices may need that)
*/
-#ifdef CONFIG_SCSI_NCR53C8XX_DISABLE_PARITY_CHECK
-#define SCSI_NCR_SETUP_SCSI_PARITY (0)
-#else
#define SCSI_NCR_SETUP_SCSI_PARITY (1)
-#endif
/*
* Settle time after reset at boot-up
--
1.9.3
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
