On Monday 28 April 2014 17:50:29 Jiang, Dave wrote: > On Mon, 2014-04-28 at 13:03 +0200, Ondrej Zary wrote: > > Hello, > > just upgraded a server running 3.2.54-2 to 3.2.57-3 (Debian Wheezy) and > > it does not boot anymore because of isci driver breakage. > > I would not run anything less than 3.8 for the isci controller. 3.2 is > VERY old for that particular driver and likely very unstable. The > product version of that driver plus libsas started with 3.8. Also I'm > concerned that you aren't using the platform OEM parameters. You need to > turn your OROM or EFI driver on for the SAS controller. It's a Cisco UCS C22 M3 server with a crappy LSI fakeraid that cannot even be disabled. It was a pain to make it boot properly - had to use dmraid. But it has been working fine since then (2012). Until now. I guess that it could be caused by the following commit but haven't tested it: commit 584ec12265192bf49dfa270d517380f6723a6956 Author: Dan Williams <dan.j.williams@xxxxxxxxx> Date: Thu Feb 6 12:23:01 2014 -0800 > > A (partial) log transcription: > > sas: DOING DISCOVERY on port 0, pid:5 > > sas: Enter sas_scsi_recover_host > > ata1: sas eh calling libata port error handler > > sas: sas_ata_hard_reset: Unable to reset I T nexus? > > sas: sas_ata_hard_reset: Found ATA device. > > sas: sas_ata_hard_reset: Unable to soft reset > > sas: sas_ata_hard_reset: Found ATA device. > > ata1: reset failed (errno=-11), retrying in 10 secs > > sas: sas_ata_hard_reset: Unable to reset I T nexus? > > sas: sas_ata_hard_reset: Found ATA device. > > sas: sas_ata_hard_reset: Unable to soft reset > > sas: sas_ata_hard_reset: Found ATA device. > > ata1: reset failed (errno=-11), retrying in 35 secs > > ata1: reset failed, giving up > > sas: --- Exit sas_scsi_recover_host > > sas: DONE DISCOVERY on port 0, pid: 5, result:0 > > sas: phy-0:1 added to port-0:1, phy_mask:0x2 (5fcfffff00000002) > > sas: DOING DISCOVERY on port 1, pid:5 > > sas: Enter sas_scsi_recover_host > > ata1: sas eh calling libata port error handler > > sas: sas_ata_hard_reset: Unable to reset I T nexus? > > sas: sas_ata_hard_reset: Found ATA device. > > sas: sas_ata_hard_reset: Unable to soft reset > > sas: sas_ata_hard_reset: Found ATA device. > > ata2: reset failed (errno=-11), retrying in 10 secs > > sas: sas_ata_hard_reset: Unable to reset I T nexus? > > sas: sas_ata_hard_reset: Found ATA device. > > sas: sas_ata_hard_reset: Unable to soft reset > > sas: sas_ata_hard_reset: Found ATA device. > > ata2: reset failed (errno=-11), retrying in 35 secs > > ata2: reset failed, giving up > > > > > > It should look like this (v3.2.54-2): > > isci: Intel(R) C600 SAS Controller Driver - version 1.0.0 > > isci 0000:03:00.0: driver configured for rev: 6 silicon > > isci 0000:03:00.0: firmware: agent loaded isci/isci_firmware.bin into > > memory isci 0000:03:00.0: OEM SAS parameters (version: 1.3) loaded > > (firmware) isci 0000:03:00.0: setting latency timer to 64 > > scsi0 : isci > > scsi1 : isci > > isci 0000:03:00.0: irq 81 for MSI/MSI-X > > isci 0000:03:00.0: irq 82 for MSI/MSI-X > > isci 0000:03:00.0: irq 83 for MSI/MSI-X > > isci 0000:03:00.0: irq 84 for MSI/MSI-X > > sas: phy-0:0 added to port-0:0, phy_mask:0x1 (5fcfffff00000001) > > sas: DOING DISCOVERY on port 0, pid:5 > > sas: Enter sas_scsi_recover_host > > ata1: sas eh calling libata port error handler > > sas: sas_ata_hard_reset: Found ATA device. > > ata1.00: ATA-8: ST9500620NS, CC02, max UDMA/133 > > ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) > > ata1.00: configured for UDMA/133 > > sas: --- Exit sas_scsi_recover_host > > scsi 0:0:0:0: Direct-Access ATA ST9500620NS CC02 PQ: 0 > > ANSI: 5 sas: DONE DISCOVERY on port 0, pid:5, result:0 > > sas: phy-0:1 added to port-0:1, phy_mask:0x2 (5fcfffff00000002) > > sas: DOING DISCOVERY on port 1, pid:5 > > sas: Enter sas_scsi_recover_host > > ata1: sas eh calling libata port error handler > > ata2: sas eh calling libata port error handler > > sas: sas_ata_hard_reset: Found ATA device. > > ata2.00: ATA-8: ST9500620NS, CC02, max UDMA/133 > > ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) > > ata2.00: configured for UDMA/133 > > sas: --- Exit sas_scsi_recover_host > > scsi 0:0:1:0: Direct-Access ATA ST9500620NS CC02 PQ: 0 > > ANSI: 5 sas: DONE DISCOVERY on port 1, pid:5, result:0 -- Ondrej Zary -- To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
