This patch adds support for APM X-Gene SoC 15Gbps Multi-purpose PHY. This
is the physical layer interface for the corresponding host controller. This
driver uses the PHY generic framework.
v13:
* Remove PHY patch for initial version as only Gen3 speed is supported
* Remove function xgene_phy_sata_force_gen and xgene_phy_set_speed
* Minor comment update to header and function xgene_phy_hw_init
v12:
* Add driver depend on HAS_IOMEM and OF
* Fix comment typo in header file phy-xgene.
* Change all macro shift value in hex to decimal
* Add time out for while loop to function sds_wr and sds_rd
* Set proper return value if failed to get IO resource 0
* Move devm_of_phy_provider_register to last operation in probe function
* Remove driver registration print statement
* Replace module init/exit with module_platform_driver
* Change license to GPL v2
v11:
* Add comment to function phy_set_speed
* Add commit log for documentation patch file
* Minor comment update to function xgene_phy_force_lat_summer_cal and
xgene_phy_sata_force_gen
v10
* Update comment for function xgene_phy_force_lat_summer_cal and
xgene_phy_sata_force_gen with function style fully-winged style
v9
* Update CMU parameter setting for register 13
* Add required delay when configure CMU PLL, Manual Calibration PLL, and VCO
PLL
* Add comment for CMU PLL calibration loop delay of 10us
* Add required delay for stopping and starting summer calibrations
* Update comment for summer and latch calibration delays
* Update comment for PHY reset Rx delay and decrease max sleep time from 500
to 150us
* Always program the DFE (equalizer) setting to 0x7e00 as with original version
* Fix Tx speed selection to always using Gen3 setting when force to an
specified generation speed
v8
* Update binding documentation
* Remove XGENE_PHY_DTS and XGENE_PHY_EXT_DTS defines
* Remove support for internal clock
* Remove support for external reference CMU
* Remove the need for external reference resource DTS entry and its related
code
v7
* Add/Update PHY CMU/lane parameters and its default values
* Rename variable enable_manual_cal to preA3Chip
* Remove function phy_rd, phy_wr, and phy_wr_flush
* Change function cmu_wr, cmu_rd, cmu_toggle1to0, cmu_clrbits, cmu_setbits,
serdes_wr, serdes_rd, serdes_clrbits, and serdes_setbits to take context
instead void *
* Remove function serdes_toggle1to0
* Decrease the polling time from 10ms to 1ms on CMU calibration complete
detection
* Move all SATA specify code in function xgene_phy_hw_initialize into
function xgene_phy_hw_init_sata
* Add usleep_range after starting summer/latch calibrations
* Add usleep_range between receiver reset (function xgene_phy_reset_rxd)
* Save and restore PHY register 31 instead writing 0 in function
xgene_phy_gen_avg_val
* Update function xgene_phy_sata_force_gen programming sequences
* Add support to reset the receiver lane in function xgene_phy_set_speed
if speed is 0
* Update PHY parameters in DTS per controller
* Some minor code clean up
v6
* Move PHY document to Documentation/devicetree/binding/phy
* Remove _ADDR from all register defines
* Update clock-names property for sataphy1clk, sataphy2clk, and sataphy3clk
v5
* Update DTS binding documentation
* Remove direct clock access and use clock interface instead
* Change override parameters to decimal instead hex values
* Change apm,tx-amplitude, apm,tx-pre-cursor1, apm,tx-pre-cursor2,
apm,tx-post-cursor to be unit of uV
v4
* Update documentation with 'apm,' instead 'apm-'
* Change DTS override parameter to have 'apm,'
* Add select GENERIC_PHY to Kconfig PHY_XGENE
* Make override parameters to be pair of three values instead one
* Some minor comment and indentation changes
* Remove error register addition offset
* Add ULL to constants
* Use module_init instead subsys_initcall
* Make DTS node based on first register address
* Update override setting values
v3
* Major re-write of the code based on various review comments
* Support external clock only at the moment
* Support SATA mode only at the moment
* No UEFI support at the moment
v2
* Remove port knowledge from functions
* Make all functions static
* Remove ID completely
* Make resource requirement based on compatible type
* Rename override PHY parameters with more descriptive name
* Add override PHY parameter for per controller, per port, and per speed
* Patch the generic PHY frame to expose set_speed operation
v1
* Initial version
Signed-off-by: Loc Ho <lho@xxxxxxx>
Signed-off-by: Tuan Phan <tphan@xxxxxxx>
Signed-off-by: Suman Tripathi <stripathi@xxxxxxx>
---
Loc Ho (3):
Documentation: Add APM X-Gene SoC 15Gbps Multi-purpose PHY driver
binding documentation
PHY: add APM X-Gene SoC 15Gbps Multi-purpose PHY driver
arm64: Add APM X-Gene SoC 15Gbps Multi-purpose PHY DTS entries
.../devicetree/bindings/phy/apm-xgene-phy.txt | 79 +
arch/arm64/boot/dts/apm-storm.dtsi | 75 +
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 2 +
drivers/phy/phy-xgene.c | 1756 ++++++++++++++++++++
5 files changed, 1919 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/phy/apm-xgene-phy.txt
create mode 100644 drivers/phy/phy-xgene.c
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
