Re: [PATCH 1/3] Documentation: Add APM X-Gene SoC 6.0Gbps SATA PHY driver binding documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

On Fri, Nov 15, 2013 at 11:26 AM, Arnd Bergmann <arnd@xxxxxxxx> wrote:
> On Friday 15 November 2013, Loc Ho wrote:
>> >> +- CTLE0                        : PHY override parameters for channel 0 register REG1
>> >> +                         field CTLE_EQ. First value for Gen1, second value
>> >> +                         for Gen2, and third value for Gen3. Default is 0x2.
>> >> +- CTLE1                        : PHY override parameters for channel 1 register REG1
>> >> +                         field CTLE_EQ. First value for Gen1, second value
>> >> +                         for Gen2, and third value for Gen3. Default is 0x2.
>> >> +- PQ0                  : PHY override parameters for channel 0 register REG125
>> >> +                         field PQ_REG. First value for Gen1, second value
>> >> +                         for Gen2, and third value for Gen3. Default is 0xA.
>> >> +- PQ1                  : PHY override parameters for channel 1 register REG125
>> >> +                         field PQ_REG. First value for Gen1, second value
>> >> +                         for Gen2, and third value for Gen3. Default is 0xA.
>> >
>> > As mentioned before, I don't think putting register-level information into the binding
>> > is the right approach here.
>> >
>> [Loc Ho]
>> I don't want to change the driver for every possible customer or APM
>> boards out there. In general, if the board designer follows the board
>> design guideline, this isn't necessary. Unfortunately, I can not
>> control what customer do. If these setting is NOT driven by DTS, then
>> I or others may have to change the driver every time there is an new
>> board. Another option is pass them as module parameters.
>
> Module parameters are certainly not a solution for this, that would make the
> problem worse.
>
> Would it be possible to read out the values that were set by the firmware
> at startup and reuse those during run-time? I assume that the devices are
> already brought up when the kernel starts.
>
> If that s not possible, change the properties to be named after what the
> setting does and make the values be units that are sensible to a board
> designer, e.g. (specifics are totally made up here)
>
>  - polarity:    If present, override the polarity of the signal line.
>                 zero for negative polarity, one for positive polarity.
>                 If absent, use the firmware default.
>  - signal-clock-frequency: If present, override the signal clock frequency.
>                 This value is defined in HZ
>  - x-y-time:    If present, override the timing setting for the X/Y signal
>                 time, in nanoseconds.
>
> This way, you can reuse the properties for an updated version of the device
> that has similar settings but a different register layout.
>
[Loc Ho]
It may be possible from ACPI point of view (hasn't tried yet). But for
DTS, there is no such firmware. I will make the entry more friendly
for DTS. For ACPI, I am thinking that the BIOS/Firmware will just
initialize it. As long as the clock isn't reset, the value will be
there. Let's agree on these:

1. DTS - use more friendly name
2. ACPI - handled by the BIOS/Firmware

-Loc
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]
  Powered by Linux