I am experiencing some issues with a RocketRAID 2760A card using the
mvsas driver. The RocketRAID2760A has 3 Marvell 88SE9485 controllers
and an integral PCIe switch, yielding a total of 24 SAS ports without
the use of SAS expanders.
At boot time I've been having some problems with drives not being
available when mounts happen. The first thing we tried was forcing
mvsas in to the initramfs to get it to load earlier - that helped a
great deal but the root cause of the issues seems to be that the first
series of commands sent to the controller are timing out. Subsequent
commands work fine, and the controller behaves properly after that.
I've done around 100TB of I/O after boot without any issue whatsoever so
I kind of suspect the issues are caused by the card not being properly
initialized somehow. All 18 of the drives I have connected currently
get from 1-4 command timeouts on the first bit of I/O. The drives are
all SATA.
I have tested this behavior and it occurs on the Ubuntu-supplied 3.2 and
3.5 kernels as well as the Ubuntu mainline 3.6.11 kernel. Currently I
am running on 3.5.0-21-generic #32.
As soon as the first I/O happens (after device discovery - that part at
least is successful), I get errors like this (full dmesg attached):
[ 37.519838]
/build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c
1858:port 5 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.519848] sd 6:0:5:0: [sdg] command ffff880115bfd600 timed out
[ 37.519878]
/build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c
1858:port 0 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.519884] sd 6:0:0:0: [sdb] command ffff88010ca02200 timed out
[ 37.519906]
/build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c
1858:port 0 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.519912] sd 13:0:0:0: [sdj] command ffff880115bfd100 timed out
[ 37.519917] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 37.519921] sas: ata16: end_device-6:5: cmd error handler
[ 37.519925] sas: ata11: end_device-6:0: cmd error handler
[ 37.520077]
/build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c
1858:port 7 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.520084] sd 14:0:5:0: [sds] command ffff88010ca49a00 timed out
[ 37.520142] sas: ata11: end_device-6:0: dev error handler
[ 37.520149] sas: ata12: end_device-6:1: dev error handler
[ 37.520159] sas: ata13: end_device-6:2: dev error handler
[ 37.520166] sas: ata14: end_device-6:3: dev error handler
[ 37.520168] sas: ata15: end_device-6:4: dev error handler
[ 37.520173] sas: ata16: end_device-6:5: dev error handler
[ 37.520177] sas: ata17: end_device-6:6: dev error handler
[ 37.520183] sas: ata18: end_device-6:7: dev error handler
[ 37.520196] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.520197] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 37.520200] sas: ata28: end_device-14:5: cmd error handler
[ 37.520211] sas: ata23: end_device-14:0: dev error handler
[ 37.520220] sas: ata24: end_device-14:1: dev error handler
[ 37.520225] sas: ata25: end_device-14:2: dev error handler
[ 37.520231] sas: ata26: end_device-14:3: dev error handler
[ 37.520236] sas: ata27: end_device-14:4: dev error handler
[ 37.520241] sas: ata28: end_device-14:5: dev error handler
[ 37.520252] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.5.0-21-generic (buildd@allspice) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #32~precise1-Ubuntu SMP Thu Dec 13 20:26:47 UTC 2012 (Ubuntu 3.5.0-21.32~precise1-generic 3.5.7.1)
[ 0.000000] Command line: BOOT_IMAGE=/vmlinuz-3.5.0-21-generic root=/dev/mapper/sys.sata.160-root ro st=buffer_kbs:256,max_buffers:32 nomodeset vga=normal
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e5000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000dff5ffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dff60000-0x00000000dff6dfff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000dff6e000-0x00000000dffdffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000dffe0000-0x00000000dfffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000011fffffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] DMI 2.4 present.
[ 0.000000] DMI: System manufacturer System Product Name/P5WDG2 WS Pro, BIOS 0905 03/06/2008
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x120000 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-DFFFF uncachable
[ 0.000000] E0000-EFFFF write-through
[ 0.000000] F0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0E0000000 mask FE0000000 uncachable
[ 0.000000] 1 base 000000000 mask F00000000 write-back
[ 0.000000] 2 base 100000000 mask FE0000000 write-back
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] original variable MTRRs
[ 0.000000] reg 0, base: 3584MB, range: 512MB, type UC
[ 0.000000] reg 1, base: 0GB, range: 4GB, type WB
[ 0.000000] reg 2, base: 4GB, range: 512MB, type WB
[ 0.000000] total RAM covered: 4096M
[ 0.000000] Found optimal setting for mtrr clean up
[ 0.000000] gran_size: 64K chunk_size: 1G num_reg: 3 lose cover RAM: 0G
[ 0.000000] New variable MTRRs
[ 0.000000] reg 0, base: 0GB, range: 4GB, type WB
[ 0.000000] reg 1, base: 3584MB, range: 512MB, type UC
[ 0.000000] reg 2, base: 4GB, range: 512MB, type WB
[ 0.000000] e820: update [mem 0xe0000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdff60 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000ff780-0x000ff78f] mapped at [ffff8800000ff780]
[ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
[ 0.000000] Base memory trampoline at [ffff880000092000] 92000 size 24576
[ 0.000000] init_memory_mapping: [mem 0x00000000-0xdff5ffff]
[ 0.000000] [mem 0x00000000-0xdfdfffff] page 2M
[ 0.000000] [mem 0xdfe00000-0xdff5ffff] page 4k
[ 0.000000] kernel direct mapping tables up to 0xdff5ffff @ [mem 0x1fffa000-0x1fffffff]
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x11fffffff]
[ 0.000000] [mem 0x100000000-0x11fffffff] page 2M
[ 0.000000] kernel direct mapping tables up to 0x11fffffff @ [mem 0xdff5e000-0xdff5ffff]
[ 0.000000] RAMDISK: [mem 0x36138000-0x37093fff]
[ 0.000000] ACPI: RSDP 00000000000f9ee0 00024 (v02 ACPIAM)
[ 0.000000] ACPI: XSDT 00000000dff60100 0004C (v01 A_M_I_ OEMXSDT 03000806 MSFT 00000097)
[ 0.000000] ACPI: FACP 00000000dff60290 000F4 (v03 A_M_I_ OEMFACP 03000806 MSFT 00000097)
[ 0.000000] ACPI: DSDT 00000000dff605a0 0992C (v01 A0520 A0520001 00000001 INTL 20060113)
[ 0.000000] ACPI: FACS 00000000dff6e000 00040
[ 0.000000] ACPI: APIC 00000000dff60390 0008C (v01 A_M_I_ OEMAPIC 03000806 MSFT 00000097)
[ 0.000000] ACPI: OEMB 00000000dff6e040 0007C (v01 A_M_I_ AMI_OEM 03000806 MSFT 00000097)
[ 0.000000] ACPI: HPET 00000000dff69ed0 00038 (v01 A_M_I_ OEMHPET 03000806 MSFT 00000097)
[ 0.000000] ACPI: MCFG 00000000dff69f10 0003C (v01 A_M_I_ OEMMCFG 03000806 MSFT 00000097)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000011fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x11fffffff]
[ 0.000000] NODE_DATA [mem 0x11fffc000-0x11fffffff]
[ 0.000000] [ffffea0000000000-ffffea00047fffff] PMD -> [ffff88011b600000-ffff88011f5fffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x11fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0009efff]
[ 0.000000] node 0: [mem 0x00100000-0xdff5ffff]
[ 0.000000] node 0: [mem 0x100000000-0x11fffffff]
[ 0.000000] On node 0 totalpages: 1048303
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 13 pages reserved
[ 0.000000] DMA zone: 3906 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 16320 pages used for memmap
[ 0.000000] DMA32 zone: 896928 pages, LIFO batch:31
[ 0.000000] Normal zone: 2048 pages used for memmap
[ 0.000000] Normal zone: 129024 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 3, version 32, address 0xfec10000, GSI 24-47
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 64
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e5000
[ 0.000000] PM: Registered nosave memory: 00000000000e5000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000dff60000 - 00000000dff6e000
[ 0.000000] PM: Registered nosave memory: 00000000dff6e000 - 00000000dffe0000
[ 0.000000] PM: Registered nosave memory: 00000000dffe0000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffb00000
[ 0.000000] PM: Registered nosave memory: 00000000ffb00000 - 0000000100000000
[ 0.000000] e820: [mem 0xe0000000-0xfedfffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88011fc00000 s83584 r8192 d22912 u524288
[ 0.000000] pcpu-alloc: s83584 r8192 d22912 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1029858
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.5.0-21-generic root=/dev/mapper/sys.sata.160-root ro st=buffer_kbs:256,max_buffers:32 nomodeset vga=normal
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 4029544k/4718592k available (6827k kernel code, 525380k absent, 163668k reserved, 6342k data, 948k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] NR_IRQS:16640 nr_irqs:1024 16
[ 0.000000] Console: colour VGA+ 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 16777216 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 2137.063 MHz processor.
[ 0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 4274.12 BogoMIPS (lpj=8548252)
[ 0.004127] pid_max: default: 32768 minimum: 301
[ 0.004212] Security Framework initialized
[ 0.004288] AppArmor: AppArmor initialized
[ 0.004346] Yama: becoming mindful.
[ 0.004835] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.008075] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.009620] Mount-cache hash table entries: 256
[ 0.009977] Initializing cgroup subsys cpuacct
[ 0.010042] Initializing cgroup subsys memory
[ 0.010112] Initializing cgroup subsys devices
[ 0.010170] Initializing cgroup subsys freezer
[ 0.010229] Initializing cgroup subsys blkio
[ 0.010288] Initializing cgroup subsys perf_event
[ 0.010381] CPU: Physical Processor ID: 0
[ 0.010439] CPU: Processor Core ID: 0
[ 0.010497] mce: CPU supports 6 MCE banks
[ 0.010560] CPU0: Thermal monitoring enabled (TM2)
[ 0.010622] using mwait in idle threads.
[ 0.013460] ACPI: Core revision 20120320
[ 0.017878] ftrace: allocating 27652 entries in 109 pages
[ 0.028582] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.069326] CPU0: Intel(R) Core(TM)2 CPU 6400 @ 2.13GHz stepping 06
[ 0.072003] Performance Events: PEBS fmt0-, 4-deep LBR, Core2 events, Intel PMU driver.
[ 0.072003] PEBS disabled due to CPU errata.
[ 0.072003] ... version: 2
[ 0.072003] ... bit width: 40
[ 0.072003] ... generic registers: 2
[ 0.072003] ... value mask: 000000ffffffffff
[ 0.072003] ... max period: 000000007fffffff
[ 0.072003] ... fixed-purpose events: 3
[ 0.072003] ... event mask: 0000000700000003
[ 0.072003] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.072003] Booting Node 0, Processors #1
[ 0.082275] Brought up 2 CPUs
[ 0.082382] Total of 2 processors activated (8548.25 BogoMIPS).
[ 0.083779] devtmpfs: initialized
[ 0.083779] EVM: security.selinux
[ 0.083779] EVM: security.SMACK64
[ 0.083779] EVM: security.capability
[ 0.084032] PM: Registering ACPI NVS region [mem 0xdff6e000-0xdffdffff] (466944 bytes)
[ 0.084897] dummy:
[ 0.084980] RTC time: 14:54:53, date: 01/10/13
[ 0.085080] NET: Registered protocol family 16
[ 0.085149] Trying to unpack rootfs image as initramfs...
[ 0.085335] ACPI: bus type pci registered
[ 0.085454] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[ 0.085540] PCI: not using MMCONFIG
[ 0.085600] PCI: Using configuration type 1 for base access
[ 0.100114] bio: create slab <bio-0> at 0
[ 0.100315] ACPI: Added _OSI(Module Device)
[ 0.100375] ACPI: Added _OSI(Processor Device)
[ 0.100434] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.100494] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.104073] ACPI: EC: Look up EC in DSDT
[ 0.105556] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.111261] ACPI: SSDT 00000000dff6e0c0 001C6 (v01 AMI CPU1PM 00000001 INTL 20060113)
[ 0.111736] ACPI: Dynamic OEM Table Load:
[ 0.111857] ACPI: SSDT (null) 001C6 (v01 AMI CPU1PM 00000001 INTL 20060113)
[ 0.112165] ACPI: SSDT 00000000dff6e290 0013A (v01 AMI CPU2PM 00000001 INTL 20060113)
[ 0.112632] ACPI: Dynamic OEM Table Load:
[ 0.112755] ACPI: SSDT (null) 0013A (v01 AMI CPU2PM 00000001 INTL 20060113)
[ 0.113139] ACPI: Interpreter enabled
[ 0.113201] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.113439] ACPI: Using IOAPIC for interrupt routing
[ 0.113530] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
[ 0.115011] PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in ACPI motherboard resources
[ 0.126679] ACPI: No dock devices found.
[ 0.126750] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.128000] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.128085] pci_root PNP0A08:00: host bridge window [io 0x0000-0x0cf7]
[ 0.128150] pci_root PNP0A08:00: host bridge window [io 0x0d00-0xffff]
[ 0.128215] pci_root PNP0A08:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.128298] pci_root PNP0A08:00: host bridge window [mem 0xe0010000-0xffffffff]
[ 0.128418] PCI host bridge to bus 0000:00
[ 0.128478] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.128541] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.128605] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.128670] pci_bus 0000:00: root bus resource [mem 0xe0010000-0xffffffff]
[ 0.128744] pci 0000:00:00.0: [8086:277c] type 00 class 0x060000
[ 0.128791] pci 0000:00:01.0: [8086:277d] type 01 class 0x060400
[ 0.128835] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.128882] pci 0000:00:1b.0: [8086:27d8] type 00 class 0x040300
[ 0.128897] pci 0000:00:1b.0: reg 10: [mem 0xef5f8000-0xef5fbfff 64bit]
[ 0.128965] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.128987] pci 0000:00:1c.0: [8086:27d0] type 01 class 0x060400
[ 0.129056] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.129082] pci 0000:00:1c.4: [8086:27e0] type 01 class 0x060400
[ 0.129152] pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
[ 0.129176] pci 0000:00:1c.5: [8086:27e2] type 01 class 0x060400
[ 0.129244] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.129267] pci 0000:00:1d.0: [8086:27c8] type 00 class 0x0c0300
[ 0.129307] pci 0000:00:1d.0: reg 20: [io 0x9880-0x989f]
[ 0.129338] pci 0000:00:1d.1: [8086:27c9] type 00 class 0x0c0300
[ 0.129379] pci 0000:00:1d.1: reg 20: [io 0x9c00-0x9c1f]
[ 0.129414] pci 0000:00:1d.2: [8086:27ca] type 00 class 0x0c0300
[ 0.129454] pci 0000:00:1d.2: reg 20: [io 0xa000-0xa01f]
[ 0.129485] pci 0000:00:1d.3: [8086:27cb] type 00 class 0x0c0300
[ 0.129525] pci 0000:00:1d.3: reg 20: [io 0xa080-0xa09f]
[ 0.129566] pci 0000:00:1d.7: [8086:27cc] type 00 class 0x0c0320
[ 0.129585] pci 0000:00:1d.7: reg 10: [mem 0xef5ff800-0xef5ffbff]
[ 0.129666] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.129688] pci 0000:00:1e.0: [8086:244e] type 01 class 0x060401
[ 0.129752] pci 0000:00:1f.0: [8086:27b8] type 00 class 0x060100
[ 0.129834] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 0007)
[ 0.129920] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 004c (mask 000b)
[ 0.130006] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 4 PIO at 4700 (mask 000f)
[ 0.130127] pci 0000:00:1f.1: [8086:27df] type 00 class 0x01018a
[ 0.130140] pci 0000:00:1f.1: reg 10: [io 0x0000-0x0007]
[ 0.130150] pci 0000:00:1f.1: reg 14: [io 0x0000-0x0003]
[ 0.130159] pci 0000:00:1f.1: reg 18: [io 0x0000-0x0007]
[ 0.130168] pci 0000:00:1f.1: reg 1c: [io 0x0000-0x0003]
[ 0.130178] pci 0000:00:1f.1: reg 20: [io 0xffa0-0xffaf]
[ 0.130215] pci 0000:00:1f.2: [8086:27c1] type 00 class 0x010601
[ 0.130231] pci 0000:00:1f.2: reg 10: [io 0xac00-0xac07]
[ 0.130239] pci 0000:00:1f.2: reg 14: [io 0xa880-0xa883]
[ 0.130248] pci 0000:00:1f.2: reg 18: [io 0xa800-0xa807]
[ 0.130256] pci 0000:00:1f.2: reg 1c: [io 0xa480-0xa483]
[ 0.130264] pci 0000:00:1f.2: reg 20: [io 0xa400-0xa40f]
[ 0.130273] pci 0000:00:1f.2: reg 24: [mem 0xef5ffc00-0xef5fffff]
[ 0.130309] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.130327] pci 0000:00:1f.3: [8086:27da] type 00 class 0x0c0500
[ 0.130378] pci 0000:00:1f.3: reg 20: [io 0x0400-0x041f]
[ 0.130453] pci 0000:06:00.0: [10b5:8648] type 01 class 0x060400
[ 0.130464] pci 0000:06:00.0: reg 10: [mem 0xefce0000-0xefcfffff]
[ 0.130524] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold
[ 0.136028] pci 0000:00:01.0: PCI bridge to [bus 06-0b]
[ 0.136097] pci 0000:00:01.0: bridge window [mem 0xefc00000-0xefffffff]
[ 0.136102] pci 0000:00:01.0: bridge window [mem 0xeef00000-0xeeffffff 64bit pref]
[ 0.136160] pci 0000:07:04.0: [10b5:8648] type 01 class 0x060400
[ 0.136231] pci 0000:07:04.0: PME# supported from D0 D3hot D3cold
[ 0.136264] pci 0000:07:05.0: [10b5:8648] type 01 class 0x060400
[ 0.136333] pci 0000:07:05.0: PME# supported from D0 D3hot D3cold
[ 0.136365] pci 0000:07:08.0: [10b5:8648] type 01 class 0x060400
[ 0.136434] pci 0000:07:08.0: PME# supported from D0 D3hot D3cold
[ 0.136466] pci 0000:07:09.0: [10b5:8648] type 01 class 0x060400
[ 0.136536] pci 0000:07:09.0: PME# supported from D0 D3hot D3cold
[ 0.136577] pci 0000:06:00.0: PCI bridge to [bus 07-0b]
[ 0.136644] pci 0000:06:00.0: bridge window [mem 0xefd00000-0xefffffff]
[ 0.136650] pci 0000:06:00.0: bridge window [mem 0xeef00000-0xeeffffff 64bit pref]
[ 0.136693] pci 0000:07:04.0: PCI bridge to [bus 0b-0b]
[ 0.136763] pci 0000:07:04.0: bridge window [mem 0xeef00000-0xeeffffff 64bit pref]
[ 0.136822] pci 0000:0a:00.0: [1103:2760] type 00 class 0x010400
[ 0.136841] pci 0000:0a:00.0: reg 10: [mem 0xeffe0000-0xefffffff 64bit]
[ 0.136856] pci 0000:0a:00.0: reg 18: [mem 0xeff80000-0xeffbffff 64bit]
[ 0.136882] pci 0000:0a:00.0: reg 30: [mem 0xeffd0000-0xeffdffff pref]
[ 0.136926] pci 0000:0a:00.0: supports D1
[ 0.136928] pci 0000:0a:00.0: PME# supported from D0 D1 D3hot
[ 0.144030] pci 0000:07:05.0: PCI bridge to [bus 0a-0a]
[ 0.144104] pci 0000:07:05.0: bridge window [mem 0xeff00000-0xefffffff]
[ 0.144174] pci 0000:09:00.0: [1103:2760] type 00 class 0x010400
[ 0.144193] pci 0000:09:00.0: reg 10: [mem 0xefee0000-0xefefffff 64bit]
[ 0.144208] pci 0000:09:00.0: reg 18: [mem 0xefe80000-0xefebffff 64bit]
[ 0.144234] pci 0000:09:00.0: reg 30: [mem 0xefed0000-0xefedffff pref]
[ 0.144282] pci 0000:09:00.0: supports D1
[ 0.144284] pci 0000:09:00.0: PME# supported from D0 D1 D3hot
[ 0.152032] pci 0000:07:08.0: PCI bridge to [bus 09-09]
[ 0.152104] pci 0000:07:08.0: bridge window [mem 0xefe00000-0xefefffff]
[ 0.152172] pci 0000:08:00.0: [1103:2760] type 00 class 0x010400
[ 0.152190] pci 0000:08:00.0: reg 10: [mem 0xefde0000-0xefdfffff 64bit]
[ 0.152205] pci 0000:08:00.0: reg 18: [mem 0xefd80000-0xefdbffff 64bit]
[ 0.152231] pci 0000:08:00.0: reg 30: [mem 0xefdd0000-0xefddffff pref]
[ 0.152276] pci 0000:08:00.0: supports D1
[ 0.152279] pci 0000:08:00.0: PME# supported from D0 D1 D3hot
[ 0.160031] pci 0000:07:09.0: PCI bridge to [bus 08-08]
[ 0.160103] pci 0000:07:09.0: bridge window [mem 0xefd00000-0xefdfffff]
[ 0.160183] pci 0000:04:00.0: [8086:032c] type 01 class 0x060400
[ 0.160208] pci 0000:04:00.0: PXH quirk detected; SHPC device MSI disabled
[ 0.160361] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[ 0.160391] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.160484] pci 0000:00:1c.0: PCI bridge to [bus 04-05]
[ 0.160547] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 0.160551] pci 0000:00:1c.0: bridge window [mem 0xef900000-0xefbfffff]
[ 0.160618] pci 0000:05:01.0: [1095:3124] type 00 class 0x018000
[ 0.160646] pci 0000:05:01.0: reg 10: [mem 0xefbbfc00-0xefbbfc7f 64bit]
[ 0.160663] pci 0000:05:01.0: reg 18: [mem 0xefbb0000-0xefbb7fff 64bit]
[ 0.160675] pci 0000:05:01.0: reg 20: [io 0xec00-0xec0f]
[ 0.160696] pci 0000:05:01.0: reg 30: [mem 0xefb00000-0xefb7ffff pref]
[ 0.160747] pci 0000:05:01.0: supports D1 D2
[ 0.160777] pci 0000:05:02.0: [1000:0030] type 00 class 0x010000
[ 0.160802] pci 0000:05:02.0: reg 10: [io 0xe400-0xe4ff]
[ 0.160819] pci 0000:05:02.0: reg 14: [mem 0xefbd0000-0xefbdffff 64bit]
[ 0.160836] pci 0000:05:02.0: reg 1c: [mem 0xefbc0000-0xefbcffff 64bit]
[ 0.160857] pci 0000:05:02.0: reg 30: [mem 0xef900000-0xef9fffff pref]
[ 0.160909] pci 0000:05:02.0: supports D1 D2
[ 0.160939] pci 0000:05:02.1: [1000:0030] type 00 class 0x010000
[ 0.160964] pci 0000:05:02.1: reg 10: [io 0xe800-0xe8ff]
[ 0.160981] pci 0000:05:02.1: reg 14: [mem 0xefbf0000-0xefbfffff 64bit]
[ 0.160998] pci 0000:05:02.1: reg 1c: [mem 0xefbe0000-0xefbeffff 64bit]
[ 0.161019] pci 0000:05:02.1: reg 30: [mem 0xefa00000-0xefafffff pref]
[ 0.161069] pci 0000:05:02.1: supports D1 D2
[ 0.161131] pci 0000:04:00.0: PCI bridge to [bus 05-05]
[ 0.161196] pci 0000:04:00.0: bridge window [io 0xe000-0xefff]
[ 0.161201] pci 0000:04:00.0: bridge window [mem 0xef900000-0xefbfffff]
[ 0.161274] pci 0000:03:00.0: [11ab:4360] type 00 class 0x020000
[ 0.161297] pci 0000:03:00.0: reg 10: [mem 0xef8fc000-0xef8fffff 64bit]
[ 0.161309] pci 0000:03:00.0: reg 18: [io 0xd800-0xd8ff]
[ 0.161352] pci 0000:03:00.0: reg 30: [mem 0xef8c0000-0xef8dffff pref]
[ 0.161420] pci 0000:03:00.0: supports D1 D2
[ 0.161422] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.161442] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.161537] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
[ 0.161599] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.161603] pci 0000:00:1c.4: bridge window [mem 0xef800000-0xef8fffff]
[ 0.161664] pci 0000:02:00.0: [11ab:6141] type 00 class 0x010681
[ 0.161681] pci 0000:02:00.0: reg 10: [io 0xcc00-0xcc07]
[ 0.161694] pci 0000:02:00.0: reg 14: [io 0xc880-0xc883]
[ 0.161706] pci 0000:02:00.0: reg 18: [io 0xc800-0xc83f]
[ 0.161729] pci 0000:02:00.0: reg 20: [io 0xc480-0xc49f]
[ 0.161741] pci 0000:02:00.0: reg 24: [mem 0xef7ffc00-0xef7fffff]
[ 0.161754] pci 0000:02:00.0: reg 30: [mem 0xef780000-0xef7bffff pref]
[ 0.161809] pci 0000:02:00.0: supports D1
[ 0.161811] pci 0000:02:00.0: PME# supported from D0 D1 D3hot
[ 0.161832] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.161928] pci 0000:00:1c.5: PCI bridge to [bus 02-02]
[ 0.161991] pci 0000:00:1c.5: bridge window [io 0xc000-0xcfff]
[ 0.161995] pci 0000:00:1c.5: bridge window [mem 0xef700000-0xef7fffff]
[ 0.162033] pci 0000:01:01.0: [1039:6326] type 00 class 0x030000
[ 0.162051] pci 0000:01:01.0: reg 10: [mem 0xee000000-0xee7fffff pref]
[ 0.162061] pci 0000:01:01.0: reg 14: [mem 0xef6e0000-0xef6effff]
[ 0.162072] pci 0000:01:01.0: reg 18: [io 0xbc00-0xbc7f]
[ 0.162108] pci 0000:01:01.0: reg 30: [mem 0xef6b0000-0xef6bffff pref]
[ 0.162136] pci 0000:01:01.0: supports D2
[ 0.162160] pci 0000:01:05.0: [11ab:4320] type 00 class 0x020000
[ 0.162180] pci 0000:01:05.0: reg 10: [mem 0xef6fc000-0xef6fffff]
[ 0.162191] pci 0000:01:05.0: reg 14: [io 0xb800-0xb8ff]
[ 0.162233] pci 0000:01:05.0: reg 30: [mem 0xef6c0000-0xef6dffff pref]
[ 0.162270] pci 0000:01:05.0: supports D1 D2
[ 0.162273] pci 0000:01:05.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.162316] pci 0000:00:1e.0: PCI bridge to [bus 01-01] (subtractive decode)
[ 0.162383] pci 0000:00:1e.0: bridge window [io 0xb000-0xbfff]
[ 0.162387] pci 0000:00:1e.0: bridge window [mem 0xef600000-0xef6fffff]
[ 0.162394] pci 0000:00:1e.0: bridge window [mem 0xee000000-0xee7fffff 64bit pref]
[ 0.162397] pci 0000:00:1e.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.162399] pci 0000:00:1e.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.162402] pci 0000:00:1e.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.162404] pci 0000:00:1e.0: bridge window [mem 0xe0010000-0xffffffff] (subtractive decode)
[ 0.162432] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.162545] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.162577] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[ 0.162636] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.162656] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.162717] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.162747] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4.PXHA._PRT]
[ 0.162785] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.162849] pci0000:00: ACPI _OSC request failed (AE_NOT_FOUND), returned control mask: 0x1d
[ 0.162932] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.166611] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.167111] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.167603] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.168058] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.168543] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 *6 7 10 11 12 14 15)
[ 0.169031] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.169522] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.170013] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.170602] vgaarb: device added: PCI:0000:01:01.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.170688] vgaarb: loaded
[ 0.170744] vgaarb: bridge control possible 0000:01:01.0
[ 0.171013] SCSI subsystem initialized
[ 0.171143] libata version 3.00 loaded.
[ 0.171167] ACPI: bus type usb registered
[ 0.171251] usbcore: registered new interface driver usbfs
[ 0.171321] usbcore: registered new interface driver hub
[ 0.171408] usbcore: registered new device driver usb
[ 0.171559] PCI: Using ACPI for IRQ routing
[ 0.172934] PCI: pci_cache_line_size set to 64 bytes
[ 0.173074] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.173076] e820: reserve RAM buffer [mem 0xdff60000-0xdfffffff]
[ 0.173191] NetLabel: Initializing
[ 0.173248] NetLabel: domain hash size = 128
[ 0.173307] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.173377] NetLabel: unlabeled traffic allowed by default
[ 0.173501] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.173568] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.173757] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.176067] Switching to clocksource hpet
[ 0.185316] AppArmor: AppArmor Filesystem Enabled
[ 0.185416] pnp: PnP ACPI init
[ 0.185495] ACPI: bus type pnp registered
[ 0.185647] pnp 00:00: [bus 00-ff]
[ 0.185650] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.185653] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.185660] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.185662] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.185665] pnp 00:00: [mem 0xe0010000-0xffffffff window]
[ 0.185740] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active)
[ 0.185751] pnp 00:01: [mem 0xfed13000-0xfed19fff]
[ 0.185827] system 00:01: [mem 0xfed13000-0xfed19fff] has been reserved
[ 0.185893] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.185923] pnp 00:02: [dma 4]
[ 0.185925] pnp 00:02: [io 0x0000-0x000f]
[ 0.185928] pnp 00:02: [io 0x0081-0x0083]
[ 0.185930] pnp 00:02: [io 0x0087]
[ 0.185932] pnp 00:02: [io 0x0089-0x008b]
[ 0.185934] pnp 00:02: [io 0x008f]
[ 0.185936] pnp 00:02: [io 0x00c0-0x00df]
[ 0.185964] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.185974] pnp 00:03: [io 0x0070-0x0071]
[ 0.185987] pnp 00:03: [irq 8]
[ 0.186017] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.186026] pnp 00:04: [io 0x0061]
[ 0.186052] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.186061] pnp 00:05: [io 0x00f0-0x00ff]
[ 0.186067] pnp 00:05: [irq 13]
[ 0.186096] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.186529] pnp 00:06: [irq 7]
[ 0.186532] pnp 00:06: [dma 3]
[ 0.186534] pnp 00:06: [io 0x0378-0x037f]
[ 0.186536] pnp 00:06: [io 0x0778-0x077f]
[ 0.186672] pnp 00:06: Plug and Play ACPI device, IDs PNP0401 (active)
[ 0.186705] pnp 00:07: [io 0x0000-0xffffffffffffffff disabled]
[ 0.186708] pnp 00:07: [io 0x0000-0xffffffffffffffff disabled]
[ 0.186711] pnp 00:07: [io 0x0290-0x0297]
[ 0.186772] system 00:07: [io 0x0290-0x0297] has been reserved
[ 0.186837] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.186934] pnp 00:08: [io 0x0010-0x001f]
[ 0.186937] pnp 00:08: [io 0x0022-0x003f]
[ 0.186939] pnp 00:08: [io 0x0044-0x004d]
[ 0.186944] pnp 00:08: [io 0x0050-0x005f]
[ 0.186946] pnp 00:08: [io 0x0062-0x0063]
[ 0.186949] pnp 00:08: [io 0x0065-0x006f]
[ 0.186951] pnp 00:08: [io 0x0072-0x007f]
[ 0.186953] pnp 00:08: [io 0x0080]
[ 0.186955] pnp 00:08: [io 0x0084-0x0086]
[ 0.186957] pnp 00:08: [io 0x0088]
[ 0.186959] pnp 00:08: [io 0x008c-0x008e]
[ 0.186961] pnp 00:08: [io 0x0090-0x009f]
[ 0.186964] pnp 00:08: [io 0x00a2-0x00bf]
[ 0.186966] pnp 00:08: [io 0x00e0-0x00ef]
[ 0.186968] pnp 00:08: [io 0x04d0-0x04d1]
[ 0.186970] pnp 00:08: [io 0x0800-0x087f]
[ 0.186972] pnp 00:08: [io 0x0400-0x041f]
[ 0.186974] pnp 00:08: [io 0x0480-0x04bf]
[ 0.186977] pnp 00:08: [mem 0xfed1c000-0xfed1ffff]
[ 0.186979] pnp 00:08: [mem 0xfed20000-0xfed3ffff]
[ 0.186981] pnp 00:08: [mem 0xfed50000-0xfed8ffff]
[ 0.186984] pnp 00:08: [mem 0xffb00000-0xffbfffff]
[ 0.186986] pnp 00:08: [mem 0xfff00000-0xffffffff]
[ 0.187089] system 00:08: [io 0x04d0-0x04d1] has been reserved
[ 0.187153] system 00:08: [io 0x0800-0x087f] has been reserved
[ 0.187217] system 00:08: [io 0x0400-0x041f] has been reserved
[ 0.187279] system 00:08: [io 0x0480-0x04bf] has been reserved
[ 0.187342] system 00:08: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.187408] system 00:08: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.187472] system 00:08: [mem 0xfed50000-0xfed8ffff] has been reserved
[ 0.187538] system 00:08: [mem 0xffb00000-0xffbfffff] has been reserved
[ 0.187602] system 00:08: [mem 0xfff00000-0xffffffff] has been reserved
[ 0.187668] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.187761] pnp 00:09: [mem 0xfed00000-0xfed003ff]
[ 0.187791] pnp 00:09: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.187881] pnp 00:0a: [mem 0xfec00000-0xfec00fff]
[ 0.187884] pnp 00:0a: [mem 0xfee00000-0xfee00fff]
[ 0.187943] system 00:0a: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.188025] system 00:0a: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.188091] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.188315] pnp 00:0b: [irq 4]
[ 0.188318] pnp 00:0b: [dma 0 disabled]
[ 0.188321] pnp 00:0b: [io 0x03f8-0x03ff]
[ 0.188402] pnp 00:0b: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.188447] pnp 00:0c: [mem 0xf0000000-0xf3ffffff]
[ 0.188505] system 00:0c: [mem 0xf0000000-0xf3ffffff] has been reserved
[ 0.188572] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.188716] pnp 00:0d: [mem 0x00000000-0x0009ffff]
[ 0.188719] pnp 00:0d: [mem 0x000c0000-0x000dffff]
[ 0.188721] pnp 00:0d: [mem 0x000e0000-0x000fffff]
[ 0.188724] pnp 00:0d: [mem 0x00100000-0xdfffffff]
[ 0.188726] pnp 00:0d: [mem 0x00000000-0xffffffffffffffff disabled]
[ 0.188795] system 00:0d: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.188862] system 00:0d: [mem 0x000c0000-0x000dffff] could not be reserved
[ 0.188928] system 00:0d: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.188993] system 00:0d: [mem 0x00100000-0xdfffffff] could not be reserved
[ 0.189061] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.189188] pnp: PnP ACPI: found 14 devices
[ 0.189246] ACPI: ACPI bus type pnp unregistered
[ 0.195652] pci 0000:07:05.0: bridge window [io 0x1000-0x0fff] to [bus 0a-0a] add_size 1000
[ 0.195658] pci 0000:07:05.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 0a-0a] add_size 200000
[ 0.195672] pci 0000:07:09.0: bridge window [io 0x1000-0x0fff] to [bus 08-08] add_size 1000
[ 0.195676] pci 0000:07:09.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 08-08] add_size 200000
[ 0.195686] pci 0000:07:05.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.195689] pci 0000:07:09.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.195693] pci 0000:06:00.0: bridge window [io 0x1000-0x0fff] to [bus 07-0b] add_size 2000
[ 0.195699] pci 0000:06:00.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 2000
[ 0.195702] pci 0000:00:01.0: bridge window [io 0x1000-0x0fff] to [bus 06-0b] add_size 2000
[ 0.195741] pci 0000:00:01.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 2000
[ 0.195747] pci 0000:00:01.0: BAR 13: assigned [io 0x1000-0x2fff]
[ 0.195813] pci 0000:06:00.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 2000
[ 0.195816] pci 0000:06:00.0: BAR 13: assigned [io 0x1000-0x2fff]
[ 0.195882] pci 0000:07:05.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.195884] pci 0000:07:09.0: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.195887] pci 0000:07:05.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.195890] pci 0000:07:09.0: res[13]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 0.195893] pci 0000:07:05.0: BAR 15: can't assign mem pref (size 0x200000)
[ 0.195959] pci 0000:07:09.0: BAR 15: can't assign mem pref (size 0x200000)
[ 0.196037] pci 0000:07:05.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 0.196100] pci 0000:07:09.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.196166] pci 0000:07:09.0: BAR 15: can't assign mem pref (size 0x200000)
[ 0.196231] pci 0000:07:09.0: BAR 13: assigned [io 0x1000-0x1fff]
[ 0.196295] pci 0000:07:05.0: BAR 15: can't assign mem pref (size 0x200000)
[ 0.196361] pci 0000:07:05.0: BAR 13: assigned [io 0x2000-0x2fff]
[ 0.196425] pci 0000:07:04.0: PCI bridge to [bus 0b-0b]
[ 0.196491] pci 0000:07:04.0: bridge window [mem 0xeef00000-0xeeffffff 64bit pref]
[ 0.196579] pci 0000:07:05.0: PCI bridge to [bus 0a-0a]
[ 0.196642] pci 0000:07:05.0: bridge window [io 0x2000-0x2fff]
[ 0.196708] pci 0000:07:05.0: bridge window [mem 0xeff00000-0xefffffff]
[ 0.196777] pci 0000:07:08.0: PCI bridge to [bus 09-09]
[ 0.196842] pci 0000:07:08.0: bridge window [mem 0xefe00000-0xefefffff]
[ 0.196912] pci 0000:07:09.0: PCI bridge to [bus 08-08]
[ 0.196975] pci 0000:07:09.0: bridge window [io 0x1000-0x1fff]
[ 0.197040] pci 0000:07:09.0: bridge window [mem 0xefd00000-0xefdfffff]
[ 0.197110] pci 0000:06:00.0: PCI bridge to [bus 07-0b]
[ 0.197171] pci 0000:06:00.0: bridge window [io 0x1000-0x2fff]
[ 0.197237] pci 0000:06:00.0: bridge window [mem 0xefd00000-0xefffffff]
[ 0.197302] pci 0000:06:00.0: bridge window [mem 0xeef00000-0xeeffffff 64bit pref]
[ 0.197389] pci 0000:00:01.0: PCI bridge to [bus 06-0b]
[ 0.197451] pci 0000:00:01.0: bridge window [io 0x1000-0x2fff]
[ 0.197515] pci 0000:00:01.0: bridge window [mem 0xefc00000-0xefffffff]
[ 0.197581] pci 0000:00:01.0: bridge window [mem 0xeef00000-0xeeffffff 64bit pref]
[ 0.197668] pci 0000:04:00.0: PCI bridge to [bus 05-05]
[ 0.197731] pci 0000:04:00.0: bridge window [io 0xe000-0xefff]
[ 0.197797] pci 0000:04:00.0: bridge window [mem 0xef900000-0xefbfffff]
[ 0.197869] pci 0000:00:1c.0: PCI bridge to [bus 04-05]
[ 0.197931] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff]
[ 0.197998] pci 0000:00:1c.0: bridge window [mem 0xef900000-0xefbfffff]
[ 0.198067] pci 0000:00:1c.4: PCI bridge to [bus 03-03]
[ 0.198128] pci 0000:00:1c.4: bridge window [io 0xd000-0xdfff]
[ 0.198194] pci 0000:00:1c.4: bridge window [mem 0xef800000-0xef8fffff]
[ 0.198264] pci 0000:00:1c.5: PCI bridge to [bus 02-02]
[ 0.198326] pci 0000:00:1c.5: bridge window [io 0xc000-0xcfff]
[ 0.198392] pci 0000:00:1c.5: bridge window [mem 0xef700000-0xef7fffff]
[ 0.198463] pci 0000:00:1e.0: PCI bridge to [bus 01-01]
[ 0.198525] pci 0000:00:1e.0: bridge window [io 0xb000-0xbfff]
[ 0.198591] pci 0000:00:1e.0: bridge window [mem 0xef600000-0xef6fffff]
[ 0.198657] pci 0000:00:1e.0: bridge window [mem 0xee000000-0xee7fffff 64bit pref]
[ 0.198749] pci 0000:00:01.0: enabling device (0106 -> 0107)
[ 0.198871] pci 0000:00:1e.0: setting latency timer to 64
[ 0.198876] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.198878] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.198881] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.198883] pci_bus 0000:00: resource 7 [mem 0xe0010000-0xffffffff]
[ 0.198886] pci_bus 0000:06: resource 0 [io 0x1000-0x2fff]
[ 0.198888] pci_bus 0000:06: resource 1 [mem 0xefc00000-0xefffffff]
[ 0.198891] pci_bus 0000:06: resource 2 [mem 0xeef00000-0xeeffffff 64bit pref]
[ 0.198893] pci_bus 0000:07: resource 0 [io 0x1000-0x2fff]
[ 0.198895] pci_bus 0000:07: resource 1 [mem 0xefd00000-0xefffffff]
[ 0.198898] pci_bus 0000:07: resource 2 [mem 0xeef00000-0xeeffffff 64bit pref]
[ 0.198900] pci_bus 0000:0b: resource 2 [mem 0xeef00000-0xeeffffff 64bit pref]
[ 0.198903] pci_bus 0000:0a: resource 0 [io 0x2000-0x2fff]
[ 0.198905] pci_bus 0000:0a: resource 1 [mem 0xeff00000-0xefffffff]
[ 0.198908] pci_bus 0000:09: resource 1 [mem 0xefe00000-0xefefffff]
[ 0.198910] pci_bus 0000:08: resource 0 [io 0x1000-0x1fff]
[ 0.198913] pci_bus 0000:08: resource 1 [mem 0xefd00000-0xefdfffff]
[ 0.198916] pci_bus 0000:04: resource 0 [io 0xe000-0xefff]
[ 0.198918] pci_bus 0000:04: resource 1 [mem 0xef900000-0xefbfffff]
[ 0.198920] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 0.198923] pci_bus 0000:05: resource 1 [mem 0xef900000-0xefbfffff]
[ 0.198925] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
[ 0.198928] pci_bus 0000:03: resource 1 [mem 0xef800000-0xef8fffff]
[ 0.198930] pci_bus 0000:02: resource 0 [io 0xc000-0xcfff]
[ 0.198933] pci_bus 0000:02: resource 1 [mem 0xef700000-0xef7fffff]
[ 0.198935] pci_bus 0000:01: resource 0 [io 0xb000-0xbfff]
[ 0.198938] pci_bus 0000:01: resource 1 [mem 0xef600000-0xef6fffff]
[ 0.198940] pci_bus 0000:01: resource 2 [mem 0xee000000-0xee7fffff 64bit pref]
[ 0.198942] pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7]
[ 0.198945] pci_bus 0000:01: resource 5 [io 0x0d00-0xffff]
[ 0.198947] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.198949] pci_bus 0000:01: resource 7 [mem 0xe0010000-0xffffffff]
[ 0.198995] NET: Registered protocol family 2
[ 0.199215] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.200478] TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
[ 0.205967] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.206709] TCP: Hash tables configured (established 524288 bind 65536)
[ 0.206775] TCP: reno registered
[ 0.206843] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.206950] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.207170] NET: Registered protocol family 1
[ 0.232091] pci 0000:04:00.0: rerouting interrupts for [8086:032c]
[ 0.232180] pci 0000:01:01.0: Boot video device
[ 0.232186] PCI: CLS 16 bytes, default 64
[ 0.232189] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.232254] software IO TLB [mem 0xdbf5e000-0xdff5dfff] (64MB) mapped at [ffff8800dbf5e000-ffff8800dff5dfff]
[ 0.232769] audit: initializing netlink socket (disabled)
[ 0.232843] type=2000 audit(1357829693.228:1): initialized
[ 0.256987] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.259272] VFS: Disk quotas dquot_6.5.2
[ 0.259383] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.259996] fuse init (API version 7.19)
[ 0.260152] msgmni has been set to 7870
[ 0.260558] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.260670] io scheduler noop registered
[ 0.260730] io scheduler deadline registered (default)
[ 0.260820] io scheduler cfq registered
[ 0.261059] pcieport 0000:00:01.0: irq 64 for MSI/MSI-X
[ 0.261145] pcieport 0000:00:1c.0: irq 65 for MSI/MSI-X
[ 0.261235] pcieport 0000:00:1c.4: irq 66 for MSI/MSI-X
[ 0.261327] pcieport 0000:00:1c.5: irq 67 for MSI/MSI-X
[ 0.261425] pcieport 0000:06:00.0: irq 68 for MSI/MSI-X
[ 0.261526] pcieport 0000:07:04.0: irq 69 for MSI/MSI-X
[ 0.261622] pcieport 0000:07:05.0: irq 70 for MSI/MSI-X
[ 0.261719] pcieport 0000:07:08.0: irq 71 for MSI/MSI-X
[ 0.261815] pcieport 0000:07:09.0: irq 72 for MSI/MSI-X
[ 0.261912] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 0.261995] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 0.262117] intel_idle: does not run on family 6 model 15
[ 0.262213] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 0.262300] ACPI: Power Button [PWRB]
[ 0.262401] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.262483] ACPI: Power Button [PWRF]
[ 0.262636] ACPI: Requesting acpi_cpufreq
[ 0.404341] Freeing initrd memory: 15728k freed
[ 0.414765] GHES: HEST is not enabled!
[ 0.415101] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 0.435513] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.457063] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 0.457387] Linux agpgart interface v0.103
[ 0.460039] brd: module loaded
[ 0.460883] loop: module loaded
[ 0.461055] ahci 0000:00:1f.2: version 3.0
[ 0.461122] ahci 0000:00:1f.2: irq 73 for MSI/MSI-X
[ 0.461182] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 0.461266] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
[ 0.461332] ahci 0000:00:1f.2: setting latency timer to 64
[ 0.461892] scsi0 : ahci
[ 0.462028] scsi1 : ahci
[ 0.462159] scsi2 : ahci
[ 0.462285] scsi3 : ahci
[ 0.462453] ata1: SATA max UDMA/133 abar m1024@0xef5ffc00 port 0xef5ffd00 irq 73
[ 0.462535] ata2: SATA max UDMA/133 abar m1024@0xef5ffc00 port 0xef5ffd80 irq 73
[ 0.462618] ata3: SATA max UDMA/133 abar m1024@0xef5ffc00 port 0xef5ffe00 irq 73
[ 0.462700] ata4: SATA max UDMA/133 abar m1024@0xef5ffc00 port 0xef5ffe80 irq 73
[ 0.462852] ata_piix 0000:00:1f.1: version 2.13
[ 0.462899] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 0.463192] scsi4 : ata_piix
[ 0.463309] scsi5 : ata_piix
[ 0.464197] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 0.464262] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 0.464626] Fixed MDIO Bus: probed
[ 0.464729] tun: Universal TUN/TAP device driver, 1.6
[ 0.464788] tun: (C) 1999-2004 Max Krasnyansky <maxk@xxxxxxxxxxxx>
[ 0.464921] PPP generic driver version 2.4.2
[ 0.465058] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.465166] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 0.465170] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 0.465238] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 0.465339] ehci_hcd 0000:00:1d.7: using broken periodic workaround
[ 0.465408] ehci_hcd 0000:00:1d.7: debug port 1
[ 0.469359] ehci_hcd 0000:00:1d.7: cache line size of 16 is not supported
[ 0.469376] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xef5ff800
[ 0.480013] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 0.480097] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.480160] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.480240] usb usb1: Product: EHCI Host Controller
[ 0.480299] usb usb1: Manufacturer: Linux 3.5.0-21-generic ehci_hcd
[ 0.480360] usb usb1: SerialNumber: 0000:00:1d.7
[ 0.480528] hub 1-0:1.0: USB hub found
[ 0.480588] hub 1-0:1.0: 8 ports detected
[ 0.480734] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.480815] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.480900] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 0.480903] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 0.480967] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.481068] uhci_hcd 0000:00:1d.0: irq 20, io base 0x00009880
[ 0.481161] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.481226] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.481306] usb usb2: Product: UHCI Host Controller
[ 0.481367] usb usb2: Manufacturer: Linux 3.5.0-21-generic uhci_hcd
[ 0.481430] usb usb2: SerialNumber: 0000:00:1d.0
[ 0.481584] hub 2-0:1.0: USB hub found
[ 0.481645] hub 2-0:1.0: 2 ports detected
[ 0.481773] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 0.481776] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 0.481841] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 0.481951] uhci_hcd 0000:00:1d.1: irq 17, io base 0x00009c00
[ 0.482042] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.482107] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.482190] usb usb3: Product: UHCI Host Controller
[ 0.482250] usb usb3: Manufacturer: Linux 3.5.0-21-generic uhci_hcd
[ 0.482313] usb usb3: SerialNumber: 0000:00:1d.1
[ 0.482461] hub 3-0:1.0: USB hub found
[ 0.482521] hub 3-0:1.0: 2 ports detected
[ 0.482649] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 0.482653] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 0.482716] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 0.482825] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a000
[ 0.482916] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.482981] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.483062] usb usb4: Product: UHCI Host Controller
[ 0.483123] usb usb4: Manufacturer: Linux 3.5.0-21-generic uhci_hcd
[ 0.483186] usb usb4: SerialNumber: 0000:00:1d.2
[ 0.483341] hub 4-0:1.0: USB hub found
[ 0.483401] hub 4-0:1.0: 2 ports detected
[ 0.483527] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 0.483531] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 0.483597] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 0.483708] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000a080
[ 0.483799] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.483862] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.483943] usb usb5: Product: UHCI Host Controller
[ 0.484013] usb usb5: Manufacturer: Linux 3.5.0-21-generic uhci_hcd
[ 0.484081] usb usb5: SerialNumber: 0000:00:1d.3
[ 0.484232] hub 5-0:1.0: USB hub found
[ 0.484292] hub 5-0:1.0: 2 ports detected
[ 0.484471] usbcore: registered new interface driver libusual
[ 0.484568] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 0.487409] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.487474] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.487665] mousedev: PS/2 mouse device common for all mice
[ 0.487863] rtc_cmos 00:03: RTC can wake from S4
[ 0.488061] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[ 0.488144] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[ 0.488288] device-mapper: uevent: version 1.0.3
[ 0.488415] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@xxxxxxxxxx
[ 0.488508] cpuidle: using governor ladder
[ 0.488564] cpuidle: using governor menu
[ 0.488622] EFI Variables Facility v0.08 2004-May-17
[ 0.488880] ashmem: initialized
[ 0.489061] TCP: cubic registered
[ 0.489228] NET: Registered protocol family 10
[ 0.489496] NET: Registered protocol family 17
[ 0.489564] Key type dns_resolver registered
[ 0.489759] PM: Hibernation image not present or could not be loaded.
[ 0.489773] registered taskstats version 1
[ 0.492384] Key type trusted registered
[ 0.494333] Key type encrypted registered
[ 0.496835] Magic number: 13:95:940
[ 0.497028] rtc_cmos 00:03: setting system clock to 2013-01-10 14:54:53 UTC (1357829693)
[ 0.497622] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 0.497685] EDD information not available.
[ 0.780023] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 0.780100] ata4: SATA link down (SStatus 0 SControl 300)
[ 0.780175] ata2: SATA link down (SStatus 0 SControl 300)
[ 0.780248] ata3: SATA link down (SStatus 0 SControl 300)
[ 0.780897] ata1.00: ATA-7: ST9160821AS, 3.ALC, max UDMA/133
[ 0.780960] ata1.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 0.782014] ata1.00: configured for UDMA/133
[ 0.782184] scsi 0:0:0:0: Direct-Access ATA ST9160821AS 3.AL PQ: 0 ANSI: 5
[ 0.782388] sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB)
[ 0.782441] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 0.782612] sd 0:0:0:0: [sda] Write Protect is off
[ 0.782672] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 0.782705] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 0.807173] sda: sda1 sda2 sda3
[ 0.807550] sd 0:0:0:0: [sda] Attached SCSI disk
[ 0.809362] Freeing unused kernel memory: 948k freed
[ 0.809661] Write protecting the kernel read-only data: 12288k
[ 0.814626] Freeing unused kernel memory: 1352k freed
[ 0.818796] Freeing unused kernel memory: 1048k freed
[ 0.836331] udevd[101]: starting version 175
[ 0.848047] usb 1-3: new high-speed USB device number 3 using ehci_hcd
[ 0.869208] mvsas 0000:0a:00.0: mvsas: driver version 0.8.16
[ 0.871243] mvsas 0000:0a:00.0: mvsas: PCI-E x8, Bandwidth Usage: 5.0 Gbps
[ 0.908302] sky2: driver version 1.30
[ 0.908439] sky2 0000:03:00.0: Yukon-2 EC chip revision 2
[ 0.908578] sky2 0000:03:00.0: irq 74 for MSI/MSI-X
[ 0.908807] sky2 0000:03:00.0: eth0: addr 00:18:f3:70:a6:3f
[ 0.950130] sata_sil24 0000:05:01.0: version 1.1
[ 0.950146] sata_sil24 0000:05:01.0: PCI IRQ 24 -> rerouted to legacy IRQ 16
[ 0.950245] sata_sil24 0000:05:01.0: Applying completion IRQ loss on PCI-X errata fix
[ 0.953770] Fusion MPT base driver 3.04.20
[ 0.953833] Copyright (c) 1999-2008 LSI Corporation
[ 0.954492] Fusion MPT SPI Host driver 3.04.20
[ 0.959779] skge: 1.14 addr 0xef6fc000 irq 21 chip Yukon-Lite rev 9
[ 0.971493] scsi7 : sata_sil24
[ 0.971709] skge 0000:01:05.0: eth1: addr 00:18:f3:70:a6:40
[ 0.979608] scsi8 : sata_sil24
[ 0.982623] scsi9 : sata_sil24
[ 0.988237] usb 1-3: New USB device found, idVendor=2304, idProduct=0227
[ 0.988306] usb 1-3: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 0.988372] usb 1-3: Product: PCTV 800e
[ 0.988431] usb 1-3: Manufacturer: Pinnacle Systems
[ 0.988491] usb 1-3: SerialNumber: 070301857419
[ 1.029875] scsi10 : sata_sil24
[ 1.030012] ata7: SATA max UDMA/100 host m128@0xefbbfc00 port 0xefbb0000 irq 16
[ 1.030098] ata8: SATA max UDMA/100 host m128@0xefbbfc00 port 0xefbb2000 irq 16
[ 1.030186] ata9: SATA max UDMA/100 host m128@0xefbbfc00 port 0xefbb4000 irq 16
[ 1.030272] ata10: SATA max UDMA/100 host m128@0xefbbfc00 port 0xefbb6000 irq 16
[ 1.030463] mptspi 0000:05:02.0: PCI IRQ 28 -> rerouted to legacy IRQ 16
[ 1.037399] mptbase: ioc0: Initiating bringup
[ 1.232031] Refined TSC clocksource calibration: 2136.988 MHz.
[ 1.232102] Switching to clocksource tsc
[ 1.284020] usb 2-2: new low-speed USB device number 2 using uhci_hcd
[ 1.464166] usb 2-2: New USB device found, idVendor=0461, idProduct=4d8a
[ 1.464235] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.465339] usb 2-2: Product: HP USB Multimedia Keyboard
[ 1.465399] usb 2-2: Manufacturer: NOVATEK
[ 1.510227] usbcore: registered new interface driver usbhid
[ 1.510295] usbhid: USB HID core driver
[ 1.524043] ioc0: LSI53C1030 B2: Capabilities={Initiator,Target}
[ 1.708023] usb 3-2: new low-speed USB device number 2 using uhci_hcd
[ 1.880054] usb 3-2: New USB device found, idVendor=0764, idProduct=0501
[ 1.880121] usb 3-2: New USB device strings: Mfr=3, Product=1, SerialNumber=0
[ 1.880185] usb 3-2: Product: CP 1350C
[ 1.880242] usb 3-2: Manufacturer: CPS
[ 2.014557] scsi11 : ioc0: LSI53C1030 B2, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=16
[ 2.014804] mptspi 0000:05:02.1: PCI IRQ 29 -> rerouted to legacy IRQ 17
[ 2.014982] mptbase: ioc1: Initiating bringup
[ 2.500082] ioc1: LSI53C1030 B2: Capabilities={Initiator,Target}
[ 2.990531] scsi12 : ioc1: LSI53C1030 B2, FwRev=01032700h, Ports=1, MaxQ=255, IRQ=17
[ 3.124019] ata7: SATA link down (SStatus 0 SControl 0)
[ 3.660010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 3.660013] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 3.779077] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 0 attach dev info is 20001
[ 3.779080] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 0 attach sas addr is 0
[ 3.880008] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 3.880010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 3.999074] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 1 attach dev info is 20001
[ 3.999076] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 1 attach sas addr is 1
[ 4.050156] scsi 11:0:4:0: Sequential-Access IBM ULT3580-TD3 87G0 PQ: 0 ANSI: 3
[ 4.050252] scsi target11:0:4: Beginning Domain Validation
[ 4.087128] scsi target11:0:4: Ending Domain Validation
[ 4.087255] scsi target11:0:4: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 127)
[ 4.093931] scsi 11:0:4:1: Medium Changer IBM 33622LX 2.40 PQ: 0 ANSI: 5
[ 4.100010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x111000
[ 4.100012] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 9
[ 4.219076] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 2 attach dev info is 20001
[ 4.219078] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 2 attach sas addr is 2
[ 4.320008] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x111000
[ 4.320010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 9
[ 4.439074] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 3 attach dev info is 20001
[ 4.439076] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 3 attach sas addr is 3
[ 5.236020] ata8: SATA link down (SStatus 0 SControl 0)
[ 6.596127] scsi 11:0:4:0: Attached scsi generic sg1 type 1
[ 6.596315] scsi 11:0:4:1: Attached scsi generic sg2 type 8
[ 7.228010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 7.228013] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 7.347077] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 4 attach dev info is 20001
[ 7.347079] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 4 attach sas addr is 4
[ 7.348023] ata9: SATA link down (SStatus 0 SControl 0)
[ 7.448011] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 7.448013] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 7.567076] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 5 attach dev info is 20001
[ 7.567078] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 5 attach sas addr is 5
[ 7.668009] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x111000
[ 7.668011] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 9
[ 7.787075] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 6 attach dev info is 20001
[ 7.787077] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 6 attach sas addr is 6
[ 7.888009] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x111000
[ 7.888011] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 9
[ 8.007074] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 7 attach dev info is 20001
[ 8.007076] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 7 attach sas addr is 7
[ 8.007085] scsi6 : mvsas
[ 8.008244] mvsas 0000:09:00.0: mvsas: driver version 0.8.16
[ 8.008339] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 0 byte dmaded.
[ 8.008342] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 1 byte dmaded.
[ 8.008345] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 2 byte dmaded.
[ 8.008348] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 3 byte dmaded.
[ 8.008350] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 4 byte dmaded.
[ 8.008353] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 5 byte dmaded.
[ 8.008356] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 6 byte dmaded.
[ 8.008358] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 7 byte dmaded.
[ 8.008409] sas: phy-6:0 added to port-6:0, phy_mask:0x1 ( 0)
[ 8.008454] sas: phy-6:1 added to port-6:1, phy_mask:0x2 ( 100000000000000)
[ 8.008488] sas: phy-6:2 added to port-6:2, phy_mask:0x4 ( 200000000000000)
[ 8.008527] sas: phy-6:3 added to port-6:3, phy_mask:0x8 ( 300000000000000)
[ 8.008567] sas: phy-6:4 added to port-6:4, phy_mask:0x1 ( 400000000000000)
[ 8.008613] sas: phy-6:5 added to port-6:5, phy_mask:0x2 ( 500000000000000)
[ 8.008654] sas: phy-6:6 added to port-6:6, phy_mask:0x4 ( 600000000000000)
[ 8.008692] sas: phy-6:7 added to port-6:7, phy_mask:0x8 ( 700000000000000)
[ 8.008712] sas: DOING DISCOVERY on port 0, pid:51
[ 8.008717] sas: DONE DISCOVERY on port 0, pid:51, result:0
[ 8.008730] sas: DOING DISCOVERY on port 1, pid:51
[ 8.008734] sas: DONE DISCOVERY on port 1, pid:51, result:0
[ 8.008746] sas: DOING DISCOVERY on port 2, pid:51
[ 8.008750] sas: DONE DISCOVERY on port 2, pid:51, result:0
[ 8.008763] sas: DOING DISCOVERY on port 3, pid:51
[ 8.008767] sas: DONE DISCOVERY on port 3, pid:51, result:0
[ 8.008779] sas: DOING DISCOVERY on port 4, pid:51
[ 8.008783] sas: DONE DISCOVERY on port 4, pid:51, result:0
[ 8.008794] sas: DOING DISCOVERY on port 5, pid:51
[ 8.008798] sas: DONE DISCOVERY on port 5, pid:51, result:0
[ 8.008810] sas: DOING DISCOVERY on port 6, pid:51
[ 8.008815] sas: DONE DISCOVERY on port 6, pid:51, result:0
[ 8.008829] sas: DOING DISCOVERY on port 7, pid:51
[ 8.008832] sas: DONE DISCOVERY on port 7, pid:51, result:0
[ 8.008844] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.008857] sas: ata11: end_device-6:0: dev error handler
[ 8.009401] mvsas 0000:09:00.0: mvsas: PCI-E x8, Bandwidth Usage: 5.0 Gbps
[ 8.170944] ata11.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
[ 8.171012] ata11.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.177950] ata11.00: configured for UDMA/133
[ 8.178032] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 8.192407] scsi 6:0:0:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
[ 8.192507] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.192518] sas: ata11: end_device-6:0: dev error handler
[ 8.192523] sas: ata12: end_device-6:1: dev error handler
[ 8.354732] ata12.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
[ 8.354798] ata12.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.360718] ata12.00: configured for UDMA/133
[ 8.360791] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 8.360990] scsi 6:0:1:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
[ 8.361086] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.361097] sas: ata11: end_device-6:0: dev error handler
[ 8.361109] sas: ata12: end_device-6:1: dev error handler
[ 8.361114] sas: ata13: end_device-6:2: dev error handler
[ 8.518128] ata13.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133
[ 8.518194] ata13.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.520427] ata13.00: configured for UDMA/133
[ 8.520499] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 8.536194] scsi 6:0:2:0: Direct-Access ATA WDC WD15EADS-00P 01.0 PQ: 0 ANSI: 5
[ 8.536289] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.536300] sas: ata11: end_device-6:0: dev error handler
[ 8.536316] sas: ata12: end_device-6:1: dev error handler
[ 8.536326] sas: ata13: end_device-6:2: dev error handler
[ 8.536338] sas: ata14: end_device-6:3: dev error handler
[ 8.694726] ata14.00: ATA-8: WDC WD15EADS-00R6B0, 01.00A01, max UDMA/133
[ 8.694793] ata14.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.698651] ata14.00: configured for UDMA/133
[ 8.698721] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 8.698917] scsi 6:0:3:0: Direct-Access ATA WDC WD15EADS-00R 01.0 PQ: 0 ANSI: 5
[ 8.699008] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.699016] sas: ata11: end_device-6:0: dev error handler
[ 8.699026] sas: ata12: end_device-6:1: dev error handler
[ 8.699031] sas: ata13: end_device-6:2: dev error handler
[ 8.699035] sas: ata14: end_device-6:3: dev error handler
[ 8.699038] sas: ata15: end_device-6:4: dev error handler
[ 8.858859] ata15.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
[ 8.858925] ata15.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 8.865833] ata15.00: configured for UDMA/133
[ 8.865905] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 8.880188] scsi 6:0:4:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
[ 8.880280] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 8.880291] sas: ata11: end_device-6:0: dev error handler
[ 8.880296] sas: ata12: end_device-6:1: dev error handler
[ 8.880306] sas: ata13: end_device-6:2: dev error handler
[ 8.880308] sas: ata14: end_device-6:3: dev error handler
[ 8.880311] sas: ata15: end_device-6:4: dev error handler
[ 8.880315] sas: ata16: end_device-6:5: dev error handler
[ 9.041882] ata16.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
[ 9.041948] ata16.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 9.047887] ata16.00: configured for UDMA/133
[ 9.047967] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 9.060187] scsi 6:0:5:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
[ 9.060285] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 9.060296] sas: ata11: end_device-6:0: dev error handler
[ 9.060311] sas: ata12: end_device-6:1: dev error handler
[ 9.060322] sas: ata13: end_device-6:2: dev error handler
[ 9.060333] sas: ata14: end_device-6:3: dev error handler
[ 9.060344] sas: ata15: end_device-6:4: dev error handler
[ 9.060354] sas: ata16: end_device-6:5: dev error handler
[ 9.060365] sas: ata17: end_device-6:6: dev error handler
[ 9.218648] ata17.00: ATA-8: WDC WD15EADS-00S2B0, 01.00A01, max UDMA/133
[ 9.218714] ata17.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 9.220680] ata17.00: configured for UDMA/133
[ 9.220757] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 9.236186] scsi 6:0:6:0: Direct-Access ATA WDC WD15EADS-00S 01.0 PQ: 0 ANSI: 5
[ 9.236277] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 9.236289] sas: ata11: end_device-6:0: dev error handler
[ 9.236299] sas: ata12: end_device-6:1: dev error handler
[ 9.236303] sas: ata13: end_device-6:2: dev error handler
[ 9.236306] sas: ata14: end_device-6:3: dev error handler
[ 9.236311] sas: ata15: end_device-6:4: dev error handler
[ 9.236313] sas: ata16: end_device-6:5: dev error handler
[ 9.236315] sas: ata17: end_device-6:6: dev error handler
[ 9.236318] sas: ata18: end_device-6:7: dev error handler
[ 9.394314] ata18.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133
[ 9.394378] ata18.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 9.396643] ata18.00: configured for UDMA/133
[ 9.396715] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 9.396908] scsi 6:0:7:0: Direct-Access ATA WDC WD15EADS-00P 01.0 PQ: 0 ANSI: 5
[ 9.397767] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 9.397868] sd 6:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 9.397951] sd 6:0:0:0: [sdb] 4096-byte physical blocks
[ 9.398173] sd 6:0:1:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 9.398258] sd 6:0:1:0: [sdc] 4096-byte physical blocks
[ 9.398403] sd 6:0:1:0: [sdc] Write Protect is off
[ 9.398463] sd 6:0:1:0: [sdc] Mode Sense: 00 3a 00 00
[ 9.398476] sd 6:0:0:0: [sdb] Write Protect is off
[ 9.398536] sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 9.398565] sd 6:0:1:0: Attached scsi generic sg4 type 0
[ 9.398664] sd 6:0:1:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.398795] sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.399125] sd 6:0:2:0: Attached scsi generic sg5 type 0
[ 9.399573] sd 6:0:3:0: Attached scsi generic sg6 type 0
[ 9.399784] sd 6:0:4:0: Attached scsi generic sg7 type 0
[ 9.399999] sd 6:0:5:0: Attached scsi generic sg8 type 0
[ 9.400220] sd 6:0:6:0: Attached scsi generic sg9 type 0
[ 9.400431] sd 6:0:7:0: Attached scsi generic sg10 type 0
[ 9.411333] sd 6:0:2:0: [sdd] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[ 9.411469] sd 6:0:2:0: [sdd] Write Protect is off
[ 9.411530] sd 6:0:2:0: [sdd] Mode Sense: 00 3a 00 00
[ 9.411553] sd 6:0:2:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.412049] sd 6:0:3:0: [sde] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[ 9.412181] sd 6:0:3:0: [sde] Write Protect is off
[ 9.412241] sd 6:0:3:0: [sde] Mode Sense: 00 3a 00 00
[ 9.412263] sd 6:0:3:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.412703] sd 6:0:4:0: [sdf] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 9.412788] sd 6:0:4:0: [sdf] 4096-byte physical blocks
[ 9.412895] sd 6:0:4:0: [sdf] Write Protect is off
[ 9.412956] sd 6:0:4:0: [sdf] Mode Sense: 00 3a 00 00
[ 9.412978] sd 6:0:4:0: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.413421] sd 6:0:5:0: [sdg] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 9.413505] sd 6:0:5:0: [sdg] 4096-byte physical blocks
[ 9.413612] sd 6:0:5:0: [sdg] Write Protect is off
[ 9.413672] sd 6:0:5:0: [sdg] Mode Sense: 00 3a 00 00
[ 9.413694] sd 6:0:5:0: [sdg] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.414133] sd 6:0:6:0: [sdh] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[ 9.414265] sd 6:0:6:0: [sdh] Write Protect is off
[ 9.414326] sd 6:0:6:0: [sdh] Mode Sense: 00 3a 00 00
[ 9.414348] sd 6:0:6:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.414838] sd 6:0:7:0: [sdi] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[ 9.414969] sd 6:0:7:0: [sdi] Write Protect is off
[ 9.415031] sd 6:0:7:0: [sdi] Mode Sense: 00 3a 00 00
[ 9.415053] sd 6:0:7:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.460024] ata10: SATA link down (SStatus 0 SControl 0)
[ 9.847294] sde: sde1 sde9
[ 9.847650] sd 6:0:3:0: [sde] Attached SCSI disk
[ 9.858890] sdc: sdc1 sdc9
[ 9.859251] sd 6:0:1:0: [sdc] Attached SCSI disk
[ 9.880426] sdg: sdg1 sdg9
[ 9.880796] sd 6:0:5:0: [sdg] Attached SCSI disk
[ 9.882566] sdf: sdf1 sdf9
[ 9.882909] sd 6:0:4:0: [sdf] Attached SCSI disk
[ 9.887383] sdh: sdh1 sdh9
[ 9.887728] sd 6:0:6:0: [sdh] Attached SCSI disk
[ 9.895348] sdb: sdb1 sdb9
[ 9.895751] sd 6:0:0:0: [sdb] Attached SCSI disk
[ 9.933730] sdd: sdd1 sdd9
[ 9.934132] sd 6:0:2:0: [sdd] Attached SCSI disk
[ 9.937675] sdi: sdi1 sdi9
[ 9.938055] sd 6:0:7:0: [sdi] Attached SCSI disk
[ 9.946073] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[ 9.948152] SCSI Media Changer driver v0.25
[ 9.948357] st 11:0:4:0: Attached scsi tape st0
[ 9.948421] st 11:0:4:0: st0: try direct i/o: yes (alignment 512 B)
[ 9.949410] osst :I: Tape driver with OnStream support version 0.99.4
[ 9.949410] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[ 9.974882] ch0: type #1 (mt): 0x1+1 [medium transport]
[ 9.974950] ch0: type #2 (st): 0x1000+22 [storage]
[ 9.975050] ch0: type #3 (ie): 0x10+1 [import/export]
[ 9.975112] ch0: type #4 (dt): 0x100+1 [data transfer]
[ 10.002232] ch0: dt 0x100: ch0: ID 4, LUN 0, ch0: name: IBM ULT3580-TD3 87G0
[ 10.002386] ch0: INITIALIZE ELEMENT STATUS, may take some time ...
[ 10.021494] ch0: ... finished
[ 10.021559] ch 11:0:4:1: Attached scsi changer ch0
[ 10.800011] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x111000
[ 10.800016] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 9
[ 10.919080] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 0 attach dev info is 20001
[ 10.919083] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 0 attach sas addr is 0
[ 11.020008] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x111000
[ 11.020010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 9
[ 11.139074] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 1 attach dev info is 20001
[ 11.139076] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 1 attach sas addr is 1
[ 11.240007] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 2 attach dev info is 0
[ 11.240009] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 2 attach sas addr is 0
[ 11.344008] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 3 attach dev info is 0
[ 11.344010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 3 attach sas addr is 0
[ 14.132009] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 14.132013] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 14.251077] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 4 attach dev info is 20001
[ 14.251079] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 4 attach sas addr is 4
[ 14.352009] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 14.352011] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 14.471075] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 5 attach dev info is 20001
[ 14.471077] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 5 attach sas addr is 5
[ 14.572008] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 6 attach dev info is 0
[ 14.572010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 6 attach sas addr is 0
[ 14.676009] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 7 attach dev info is 0
[ 14.676011] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 7 attach sas addr is 0
[ 14.676019] scsi13 : mvsas
[ 14.676690] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 0 byte dmaded.
[ 14.676695] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 1 byte dmaded.
[ 14.676698] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 4 byte dmaded.
[ 14.676700] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 5 byte dmaded.
[ 14.676741] sas: phy-13:0 added to port-13:0, phy_mask:0x1 ( 0)
[ 14.676787] sas: phy-13:1 added to port-13:1, phy_mask:0x2 ( 100000000000000)
[ 14.676830] sas: phy-13:4 added to port-13:2, phy_mask:0x1 ( 400000000000000)
[ 14.676872] sas: phy-13:5 added to port-13:3, phy_mask:0x2 ( 500000000000000)
[ 14.676894] sas: DOING DISCOVERY on port 0, pid:55
[ 14.676901] sas: DONE DISCOVERY on port 0, pid:55, result:0
[ 14.676913] sas: DOING DISCOVERY on port 1, pid:55
[ 14.676918] sas: DONE DISCOVERY on port 1, pid:55, result:0
[ 14.676929] sas: DOING DISCOVERY on port 2, pid:55
[ 14.676934] sas: DONE DISCOVERY on port 2, pid:55, result:0
[ 14.676946] sas: DOING DISCOVERY on port 3, pid:55
[ 14.676951] sas: DONE DISCOVERY on port 3, pid:55, result:0
[ 14.676964] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 14.676972] mvsas 0000:08:00.0: mvsas: driver version 0.8.16
[ 14.676975] sas: ata19: end_device-13:0: dev error handler
[ 14.677317] mvsas 0000:08:00.0: mvsas: PCI-E x8, Bandwidth Usage: 5.0 Gbps
[ 14.835315] ata19.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
[ 14.835381] ata19.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 14.839188] ata19.00: configured for UDMA/133
[ 14.839256] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 14.852262] scsi 13:0:0:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
[ 14.852358] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 14.852369] sas: ata19: end_device-13:0: dev error handler
[ 14.852379] sas: ata20: end_device-13:1: dev error handler
[ 15.011829] ata20.00: ATA-8: WDC WD20EARS-00MVWB0, 51.0AB51, max UDMA/133
[ 15.011894] ata20.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 15.015832] ata20.00: configured for UDMA/133
[ 15.015896] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 15.028192] scsi 13:0:1:0: Direct-Access ATA WDC WD20EARS-00M 51.0 PQ: 0 ANSI: 5
[ 15.028286] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 15.028296] sas: ata19: end_device-13:0: dev error handler
[ 15.028305] sas: ata20: end_device-13:1: dev error handler
[ 15.028311] sas: ata21: end_device-13:2: dev error handler
[ 15.184755] ata21.00: ATA-8: ST2000DL003-9VT166, CC32, max UDMA/133
[ 15.184819] ata21.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 15.185675] ata21.00: configured for UDMA/133
[ 15.185740] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 15.200192] scsi 13:0:2:0: Direct-Access ATA ST2000DL003-9VT1 CC32 PQ: 0 ANSI: 5
[ 15.200287] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 15.200297] sas: ata19: end_device-13:0: dev error handler
[ 15.200306] sas: ata20: end_device-13:1: dev error handler
[ 15.200315] sas: ata21: end_device-13:2: dev error handler
[ 15.200316] sas: ata22: end_device-13:3: dev error handler
[ 15.356731] ata22.00: ATA-8: ST2000DL003-9VT166, CC32, max UDMA/133
[ 15.356795] ata22.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 15.357646] ata22.00: configured for UDMA/133
[ 15.357715] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 15.372254] scsi 13:0:3:0: Direct-Access ATA ST2000DL003-9VT1 CC32 PQ: 0 ANSI: 5
[ 15.373598] sd 13:0:0:0: Attached scsi generic sg11 type 0
[ 15.373824] sd 13:0:1:0: Attached scsi generic sg12 type 0
[ 15.374041] sd 13:0:2:0: Attached scsi generic sg13 type 0
[ 15.374593] sd 13:0:3:0: Attached scsi generic sg14 type 0
[ 15.374806] sd 13:0:2:0: [sdl] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 15.374940] sd 13:0:2:0: [sdl] Write Protect is off
[ 15.375001] sd 13:0:2:0: [sdl] Mode Sense: 00 3a 00 00
[ 15.375024] sd 13:0:2:0: [sdl] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.375329] sd 13:0:1:0: [sdk] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 15.375460] sd 13:0:1:0: [sdk] Write Protect is off
[ 15.375521] sd 13:0:1:0: [sdk] Mode Sense: 00 3a 00 00
[ 15.375543] sd 13:0:1:0: [sdk] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.376211] sd 13:0:0:0: [sdj] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 15.376343] sd 13:0:0:0: [sdj] Write Protect is off
[ 15.376404] sd 13:0:0:0: [sdj] Mode Sense: 00 3a 00 00
[ 15.376425] sd 13:0:0:0: [sdj] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.376869] sd 13:0:3:0: [sdm] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 15.377001] sd 13:0:3:0: [sdm] Write Protect is off
[ 15.377061] sd 13:0:3:0: [sdm] Mode Sense: 00 3a 00 00
[ 15.377083] sd 13:0:3:0: [sdm] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 15.417550] sdm: sdm1 sdm9
[ 15.417882] sd 13:0:3:0: [sdm] Attached SCSI disk
[ 15.424198] sdl: sdl1 sdl9
[ 15.424486] sd 13:0:2:0: [sdl] Attached SCSI disk
[ 15.840383] sdk: sdk1 sdk9
[ 15.840749] sd 13:0:1:0: [sdk] Attached SCSI disk
[ 15.859228] sdj: sdj1 sdj9
[ 15.859515] sd 13:0:0:0: [sdj] Attached SCSI disk
[ 17.468009] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 17.468012] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 17.587077] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 0 attach dev info is 20001
[ 17.587079] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 0 attach sas addr is 0
[ 17.688009] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 17.688011] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 17.807074] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 1 attach dev info is 20001
[ 17.807076] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 1 attach sas addr is 1
[ 17.908008] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 2 attach dev info is 0
[ 17.908010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 2 attach sas addr is 0
[ 18.012013] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 3 attach dev info is 0
[ 18.012016] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 3 attach sas addr is 0
[ 20.800008] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 20.800011] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 20.919075] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 4 attach dev info is 20001
[ 20.919077] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 4 attach sas addr is 4
[ 21.020008] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x122000
[ 21.020010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 10
[ 21.139074] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 5 attach dev info is 20001
[ 21.139076] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 5 attach sas addr is 5
[ 21.240008] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x111000
[ 21.240010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 9
[ 21.359073] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 6 attach dev info is 20001
[ 21.359075] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 6 attach sas addr is 6
[ 21.460009] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 838:get all reg link rate is 0x111000
[ 21.460010] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 843:get link rate is 9
[ 21.579074] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1175:phy 7 attach dev info is 20001
[ 21.579076] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1177:phy 7 attach sas addr is 7
[ 21.579084] scsi14 : mvsas
[ 21.579750] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 0 byte dmaded.
[ 21.579757] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 1 byte dmaded.
[ 21.579760] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 4 byte dmaded.
[ 21.579762] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 5 byte dmaded.
[ 21.579764] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 6 byte dmaded.
[ 21.579767] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 277:phy 7 byte dmaded.
[ 21.579804] sas: phy-14:0 added to port-14:0, phy_mask:0x1 ( 0)
[ 21.579849] sas: phy-14:1 added to port-14:1, phy_mask:0x2 ( 100000000000000)
[ 21.579892] sas: phy-14:4 added to port-14:2, phy_mask:0x1 ( 400000000000000)
[ 21.579935] sas: phy-14:5 added to port-14:3, phy_mask:0x2 ( 500000000000000)
[ 21.579977] sas: phy-14:6 added to port-14:4, phy_mask:0x4 ( 600000000000000)
[ 21.580028] sas: phy-14:7 added to port-14:5, phy_mask:0x8 ( 700000000000000)
[ 21.580047] sas: DOING DISCOVERY on port 0, pid:51
[ 21.580054] sas: DONE DISCOVERY on port 0, pid:51, result:0
[ 21.580064] sas: DOING DISCOVERY on port 1, pid:51
[ 21.580069] sas: DONE DISCOVERY on port 1, pid:51, result:0
[ 21.580080] sas: DOING DISCOVERY on port 2, pid:51
[ 21.580085] sas: DONE DISCOVERY on port 2, pid:51, result:0
[ 21.580095] sas: DOING DISCOVERY on port 3, pid:51
[ 21.580100] sas: DONE DISCOVERY on port 3, pid:51, result:0
[ 21.580111] sas: DOING DISCOVERY on port 4, pid:51
[ 21.580115] sas: DONE DISCOVERY on port 4, pid:51, result:0
[ 21.580125] sas: DOING DISCOVERY on port 5, pid:51
[ 21.580130] sas: DONE DISCOVERY on port 5, pid:51, result:0
[ 21.580143] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 21.580152] sas: ata23: end_device-14:0: dev error handler
[ 21.736516] ata23.00: ATA-9: WDC WD20EFRX-68AX9N0, 80.00A80, max UDMA/133
[ 21.736585] ata23.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 21.737161] ata23.00: configured for UDMA/133
[ 21.737383] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 21.752780] scsi 14:0:0:0: Direct-Access ATA WDC WD20EFRX-68A 80.0 PQ: 0 ANSI: 5
[ 21.752981] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 21.752996] sas: ata23: end_device-14:0: dev error handler
[ 21.753000] sas: ata24: end_device-14:1: dev error handler
[ 21.793214] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null)
[ 21.908524] ata24.00: ATA-9: WDC WD20EFRX-68AX9N0, 80.00A80, max UDMA/133
[ 21.908595] ata24.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 21.909170] ata24.00: configured for UDMA/133
[ 21.909249] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 21.924258] scsi 14:0:1:0: Direct-Access ATA WDC WD20EFRX-68A 80.0 PQ: 0 ANSI: 5
[ 21.924356] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 21.924368] sas: ata23: end_device-14:0: dev error handler
[ 21.924380] sas: ata24: end_device-14:1: dev error handler
[ 21.924388] sas: ata25: end_device-14:2: dev error handler
[ 22.085724] ata25.00: ATA-8: WDC WD20EARX-00PASB0, 51.0AB51, max UDMA/133
[ 22.085791] ata25.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 22.091759] ata25.00: configured for UDMA/133
[ 22.091828] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 22.104210] scsi 14:0:2:0: Direct-Access ATA WDC WD20EARX-00P 51.0 PQ: 0 ANSI: 5
[ 22.104305] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 22.104316] sas: ata23: end_device-14:0: dev error handler
[ 22.104320] sas: ata24: end_device-14:1: dev error handler
[ 22.104327] sas: ata25: end_device-14:2: dev error handler
[ 22.104328] sas: ata26: end_device-14:3: dev error handler
[ 22.260502] ata26.00: ATA-9: WDC WD20EFRX-68AX9N0, 80.00A80, max UDMA/133
[ 22.260571] ata26.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 22.261156] ata26.00: configured for UDMA/133
[ 22.261227] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 22.276220] scsi 14:0:3:0: Direct-Access ATA WDC WD20EFRX-68A 80.0 PQ: 0 ANSI: 5
[ 22.276315] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 22.276326] sas: ata23: end_device-14:0: dev error handler
[ 22.276332] sas: ata24: end_device-14:1: dev error handler
[ 22.276338] sas: ata25: end_device-14:2: dev error handler
[ 22.276341] sas: ata26: end_device-14:3: dev error handler
[ 22.276344] sas: ata27: end_device-14:4: dev error handler
[ 22.434383] ata27.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133
[ 22.434450] ata27.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 22.436553] ata27.00: configured for UDMA/133
[ 22.436621] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 22.452200] scsi 14:0:4:0: Direct-Access ATA WDC WD15EADS-00P 01.0 PQ: 0 ANSI: 5
[ 22.452295] sas: Enter sas_scsi_recover_host busy: 0 failed: 0
[ 22.452306] sas: ata23: end_device-14:0: dev error handler
[ 22.452311] sas: ata24: end_device-14:1: dev error handler
[ 22.452316] sas: ata25: end_device-14:2: dev error handler
[ 22.452319] sas: ata26: end_device-14:3: dev error handler
[ 22.452322] sas: ata27: end_device-14:4: dev error handler
[ 22.452325] sas: ata28: end_device-14:5: dev error handler
[ 22.610269] ata28.00: ATA-8: WDC WD15EADS-00P8B0, 01.00A01, max UDMA/133
[ 22.610339] ata28.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 22.612634] ata28.00: configured for UDMA/133
[ 22.612706] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 22.628243] scsi 14:0:5:0: Direct-Access ATA WDC WD15EADS-00P 01.0 PQ: 0 ANSI: 5
[ 22.628461] sd 14:0:0:0: [sdn] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 22.628488] sd 14:0:0:0: Attached scsi generic sg15 type 0
[ 22.628608] sd 14:0:0:0: [sdn] 4096-byte physical blocks
[ 22.628636] sd 14:0:1:0: Attached scsi generic sg16 type 0
[ 22.628763] sd 14:0:1:0: [sdo] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 22.628799] sd 14:0:2:0: Attached scsi generic sg17 type 0
[ 22.628909] sd 14:0:1:0: [sdo] 4096-byte physical blocks
[ 22.628939] sd 14:0:3:0: Attached scsi generic sg18 type 0
[ 22.629106] sd 14:0:2:0: [sdp] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 22.629110] sd 14:0:4:0: [sdr] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[ 22.629157] sd 14:0:4:0: [sdr] Write Protect is off
[ 22.629160] sd 14:0:4:0: [sdr] Mode Sense: 00 3a 00 00
[ 22.629181] sd 14:0:4:0: [sdr] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.629225] sd 14:0:1:0: [sdo] Write Protect is off
[ 22.629227] sd 14:0:1:0: [sdo] Mode Sense: 00 3a 00 00
[ 22.629249] sd 14:0:1:0: [sdo] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.629319] sd 14:0:0:0: [sdn] Write Protect is off
[ 22.629321] sd 14:0:0:0: [sdn] Mode Sense: 00 3a 00 00
[ 22.629343] sd 14:0:0:0: [sdn] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.629704] sd 14:0:2:0: [sdp] 4096-byte physical blocks
[ 22.629800] sd 14:0:3:0: [sdq] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 22.629887] sd 14:0:3:0: [sdq] 4096-byte physical blocks
[ 22.629986] sd 14:0:4:0: Attached scsi generic sg19 type 0
[ 22.630111] sd 14:0:2:0: [sdp] Write Protect is off
[ 22.630172] sd 14:0:2:0: [sdp] Mode Sense: 00 3a 00 00
[ 22.630301] sd 14:0:5:0: [sds] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[ 22.630358] sd 14:0:3:0: [sdq] Write Protect is off
[ 22.630360] sd 14:0:3:0: [sdq] Mode Sense: 00 3a 00 00
[ 22.630372] sd 14:0:2:0: [sdp] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.630422] sd 14:0:3:0: [sdq] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.630568] sd 14:0:5:0: Attached scsi generic sg20 type 0
[ 22.630730] sd 14:0:5:0: [sds] Write Protect is off
[ 22.630792] sd 14:0:5:0: [sds] Mode Sense: 00 3a 00 00
[ 22.630817] sd 14:0:5:0: [sds] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 22.688575] sdn: sdn1 sdn9
[ 22.688860] sdo: sdo1 sdo9
[ 22.688974] sd 14:0:0:0: [sdn] Attached SCSI disk
[ 22.689186] sd 14:0:1:0: [sdo] Attached SCSI disk
[ 22.692366] sdq: sdq1 sdq9
[ 22.692736] sd 14:0:3:0: [sdq] Attached SCSI disk
[ 22.929992] init: ureadahead main process (562) terminated with status 5
[ 23.124791] sdp: sdp1 sdp9
[ 23.125188] sd 14:0:2:0: [sdp] Attached SCSI disk
[ 23.133782] sds: sds1 sds9
[ 23.134105] sd 14:0:5:0: [sds] Attached SCSI disk
[ 23.135064] sdr: sdr1 sdr9
[ 23.135380] sd 14:0:4:0: [sdr] Attached SCSI disk
[ 28.336999] SPL: Loaded module v0.6.0.91-rc13
[ 28.354206] zunicode: module license 'CDDL' taints kernel.
[ 28.354268] Disabling lock debugging due to kernel taint
[ 32.119435] ZFS: Loaded module v0.6.0.91-rc13, ZFS pool version 28, ZFS filesystem version 5
[ 32.126397] SPL: using hostid 0x007f0101
[ 32.615011] Adding 16777212k swap on /dev/sda2. Priority:-1 extents:1 across:16777212k
[ 33.324688] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 33.324697] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 33.555540] udevd[927]: starting version 175
[ 34.081276] lp: driver loaded but no devices found
[ 34.232156] coretemp coretemp.0: Using relative temperature scale!
[ 34.232173] coretemp coretemp.0: Using relative temperature scale!
[ 34.325156] w83627ehf: Found W83627DHG chip at 0x290
[ 34.325192] ACPI Warning: 0x0000000000000295-0x0000000000000296 SystemIO conflicts with Region \_SB_.PCI0.SBRG.SIOR.HWRE 1 (20120320/utaddress-251)
[ 34.325198] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 34.644166] parport_pc 00:06: reported by Plug and Play ACPI
[ 34.644274] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[ 34.740160] lp0: using parport0 (interrupt-driven).
[ 34.843424] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[ 34.904970] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 34.917562] ppdev: user-space parallel port driver
[ 34.931783] EDAC MC: Ver: 2.1.0
[ 34.977854] EDAC i82975x: ECC disabled on both channels.
[ 35.000623] intel_rng: FWH not detected
[ 35.006315] microcode: CPU0 sig=0x6f6, pf=0x1, revision=0xcb
[ 35.059090] input: NOVATEK HP USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input2
[ 35.060961] hid-generic 0003:0461:4D8A.0001: input,hidraw0: USB HID v1.11 Keyboard [NOVATEK HP USB Multimedia Keyboard] on usb-0000:00:1d.0-2/input0
[ 35.069348] input: NOVATEK HP USB Multimedia Keyboard as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.1/input/input3
[ 35.069886] hid-generic 0003:0461:4D8A.0002: input,hidraw1: USB HID v1.11 Device [NOVATEK HP USB Multimedia Keyboard] on usb-0000:00:1d.0-2/input1
[ 35.172045] hid-generic 0003:0764:0501.0003: hiddev0,hidraw2: USB HID v1.10 Device [CPS CP 1350C] on usb-0000:00:1d.1-2/input0
[ 35.176615] ACPI Warning: 0x0000000000000830-0x0000000000000833 SystemIO conflicts with Region \SMIE 1 (20120320/utaddress-251)
[ 35.176624] ACPI Warning: 0x0000000000000830-0x0000000000000833 SystemIO conflicts with Region \_SB_.PCI0.SBRG.SMIE 2 (20120320/utaddress-251)
[ 35.176629] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 35.176631] lpc_ich: Resource conflict(s) found affecting iTCO_wdt
[ 35.176639] ACPI Warning: 0x0000000000000480-0x00000000000004bf SystemIO conflicts with Region \_SB_.PCI0.SBRG.GPIO 1 (20120320/utaddress-251)
[ 35.176643] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 35.176645] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 35.725654] leds_ss4200: no LED devices found
[ 35.800405] microcode: CPU1 sig=0x6f6, pf=0x1, revision=0xcb
[ 35.802330] microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba
[ 36.886508] Linux video capture interface: v2.00
[ 37.380775] em28xx: New device Pinnacle Systems PCTV 800e @ 480 Mbps (2304:0227, interface 0, class 0)
[ 37.380779] em28xx: Audio Vendor Class interface 0 found
[ 37.380781] em28xx: Video interface 0 found
[ 37.380782] em28xx: DVB interface 0 found
[ 37.380865] em28xx #0: chip ID is em2882/em2883
[ 37.498826] hda_intel: msi for device 1043:81f6 set to 0
[ 37.519838] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 5 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.519848] sd 6:0:5:0: [sdg] command ffff880115bfd600 timed out
[ 37.519878] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 0 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.519884] sd 6:0:0:0: [sdb] command ffff88010ca02200 timed out
[ 37.519906] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 0 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.519912] sd 13:0:0:0: [sdj] command ffff880115bfd100 timed out
[ 37.519917] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 37.519921] sas: ata16: end_device-6:5: cmd error handler
[ 37.519925] sas: ata11: end_device-6:0: cmd error handler
[ 37.520077] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 7 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.520084] sd 14:0:5:0: [sds] command ffff88010ca49a00 timed out
[ 37.520142] sas: ata11: end_device-6:0: dev error handler
[ 37.520149] sas: ata12: end_device-6:1: dev error handler
[ 37.520159] sas: ata13: end_device-6:2: dev error handler
[ 37.520166] sas: ata14: end_device-6:3: dev error handler
[ 37.520168] sas: ata15: end_device-6:4: dev error handler
[ 37.520173] sas: ata16: end_device-6:5: dev error handler
[ 37.520177] sas: ata17: end_device-6:6: dev error handler
[ 37.520183] sas: ata18: end_device-6:7: dev error handler
[ 37.520196] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.520197] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 37.520200] sas: ata28: end_device-14:5: cmd error handler
[ 37.520211] sas: ata23: end_device-14:0: dev error handler
[ 37.520220] sas: ata24: end_device-14:1: dev error handler
[ 37.520225] sas: ata25: end_device-14:2: dev error handler
[ 37.520231] sas: ata26: end_device-14:3: dev error handler
[ 37.520236] sas: ata27: end_device-14:4: dev error handler
[ 37.520241] sas: ata28: end_device-14:5: dev error handler
[ 37.520252] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.520391] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 4 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.520397] sd 14:0:2:0: [sdp] command ffff88010d5eaa00 timed out
[ 37.520450] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 6 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.520453] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 626:command active 00000004, slot [0].
[ 37.520458] sd 6:0:6:0: [sdh] command ffff880115bfd600 timed out
[ 37.520461] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 4 slot 1 rx_desc 30001 has error info0000000001000000.
[ 37.520464] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 626:command active 00000004, slot [1].
[ 37.520470] sd 6:0:4:0: [sdf] command ffff88010d5ea600 timed out
[ 37.520476] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 0 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.520481] sd 14:0:0:0: [sdn] command ffff88010d57c800 timed out
[ 37.520504] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 3 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.520509] sd 6:0:3:0: [sde] command ffff88010d5ea400 timed out
[ 37.520527] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 37.520530] sas: ata25: end_device-14:2: cmd error handler
[ 37.520533] sas: ata23: end_device-14:0: cmd error handler
[ 37.520543] sas: ata23: end_device-14:0: dev error handler
[ 37.520556] sas: ata24: end_device-14:1: dev error handler
[ 37.520561] sas: ata25: end_device-14:2: dev error handler
[ 37.520570] sas: ata26: end_device-14:3: dev error handler
[ 37.520575] sas: ata27: end_device-14:4: dev error handler
[ 37.520579] sas: ata28: end_device-14:5: dev error handler
[ 37.520585] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.520718] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 7 slot 2 rx_desc 30002 has error info0000000001000000.
[ 37.520723] sd 6:0:7:0: [sdi] command ffff88010d57ca00 timed out
[ 37.520739] sas: Enter sas_scsi_recover_host busy: 4 failed: 4
[ 37.520742] sas: ata17: end_device-6:6: cmd error handler
[ 37.520745] sas: ata15: end_device-6:4: cmd error handler
[ 37.520748] sas: ata14: end_device-6:3: cmd error handler
[ 37.520750] sas: ata18: end_device-6:7: cmd error handler
[ 37.520760] sas: ata11: end_device-6:0: dev error handler
[ 37.520766] sas: ata12: end_device-6:1: dev error handler
[ 37.520770] sas: ata13: end_device-6:2: dev error handler
[ 37.520774] sas: ata14: end_device-6:3: dev error handler
[ 37.520784] sas: ata15: end_device-6:4: dev error handler
[ 37.520793] sas: ata16: end_device-6:5: dev error handler
[ 37.520798] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 5 slot 2 rx_desc 30002 has error info0000000001000000.
[ 37.520799] sas: ata17: end_device-6:6: dev error handler
[ 37.520803] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 626:command active 00000003, slot [2].
[ 37.520808] sas: ata18: end_device-6:7: dev error handler
[ 37.520810] sd 14:0:3:0: [sdq] command ffff88010d5ea700 timed out
[ 37.520822] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.520851] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 1 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.520855] sd 14:0:1:0: [sdo] command ffff88010d5ea500 timed out
[ 37.521084] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 4 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.521090] sd 13:0:2:0: [sdl] command ffff880115bfd900 timed out
[ 37.521105] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 37.521109] sas: ata19: end_device-13:0: cmd error handler
[ 37.521113] sas: ata21: end_device-13:2: cmd error handler
[ 37.521123] sas: ata19: end_device-13:0: dev error handler
[ 37.521138] sas: ata20: end_device-13:1: dev error handler
[ 37.521144] sas: ata21: end_device-13:2: dev error handler
[ 37.521153] sas: ata22: end_device-13:3: dev error handler
[ 37.521161] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.521450] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 1 slot 1 rx_desc 30001 has error info0000000001000000.
[ 37.521454] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 626:command active 00000001, slot [1].
[ 37.521459] sd 13:0:1:0: [sdk] command ffff88010ca41600 timed out
[ 37.521472] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 1 slot 2 rx_desc 30002 has error info0000000001000000.
[ 37.521475] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 626:command active 00000003, slot [2].
[ 37.521480] sd 6:0:1:0: [sdc] command ffff88010ca41b00 timed out
[ 37.521774] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 2 slot 2 rx_desc 30002 has error info0000000001000000.
[ 37.521777] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 626:command active 00000003, slot [2].
[ 37.521783] sd 6:0:2:0: [sdd] command ffff88010ca41f00 timed out
[ 37.521803] sd 13:0:2:0: [sdl] command ffff88010ca41400 timed out
[ 37.522249] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 5 slot 1 rx_desc 30001 has error info0000000001000000.
[ 37.522254] sd 13:0:3:0: [sdm] command ffff88010ca41300 timed out
[ 37.522984] sd 6:0:6:0: [sdh] command ffff88010d5b0300 timed out
[ 37.524893] sd 13:0:0:0: [sdj] command ffff88010ca41d00 timed out
[ 37.524912] sas: Enter sas_scsi_recover_host busy: 4 failed: 4
[ 37.524916] sas: ata20: end_device-13:1: cmd error handler
[ 37.524924] sas: ata21: end_device-13:2: cmd error handler
[ 37.524927] sas: ata22: end_device-13:3: cmd error handler
[ 37.524930] sas: ata19: end_device-13:0: cmd error handler
[ 37.524948] sas: ata19: end_device-13:0: dev error handler
[ 37.524971] sas: ata20: end_device-13:1: dev error handler
[ 37.524993] sas: ata21: end_device-13:2: dev error handler
[ 37.524994] sas: ata22: end_device-13:3: dev error handler
[ 37.525016] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.525224] sd 6:0:3:0: [sde] command ffff880115bfd600 timed out
[ 37.525254] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 4 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.525259] sd 13:0:2:0: [sdl] command ffff8801161a8400 timed out
[ 37.526419] sd 14:0:2:0: [sdp] command ffff88010d5eaa00 timed out
[ 37.526639] sas: Enter sas_scsi_recover_host busy: 3 failed: 3
[ 37.526646] sas: ata26: end_device-14:3: cmd error handler
[ 37.526653] sas: ata24: end_device-14:1: cmd error handler
[ 37.526656] sas: ata25: end_device-14:2: cmd error handler
[ 37.526677] sas: ata23: end_device-14:0: dev error handler
[ 37.526697] sas: ata24: end_device-14:1: dev error handler
[ 37.526723] sas: ata25: end_device-14:2: dev error handler
[ 37.526738] sas: ata26: end_device-14:3: dev error handler
[ 37.526751] sas: ata27: end_device-14:4: dev error handler
[ 37.526758] sas: ata28: end_device-14:5: dev error handler
[ 37.526786] sd 6:0:5:0: [sdg] command ffff88010d5b0d00 timed out
[ 37.526996] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.527291] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 4 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.527296] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 626:command active 00000002, slot [0].
[ 37.527303] sd 14:0:2:0: [sdp] command ffff8801161aff00 timed out
[ 37.527670] sd 14:0:1:0: [sdo] command ffff88010ca46f00 timed out
[ 37.527681] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 37.527686] sas: ata25: end_device-14:2: cmd error handler
[ 37.527690] sas: ata24: end_device-14:1: cmd error handler
[ 37.527705] sas: ata23: end_device-14:0: dev error handler
[ 37.527719] sas: ata24: end_device-14:1: dev error handler
[ 37.527734] sas: ata25: end_device-14:2: dev error handler
[ 37.527746] sas: ata26: end_device-14:3: dev error handler
[ 37.527754] sas: ata27: end_device-14:4: dev error handler
[ 37.527761] sas: ata28: end_device-14:5: dev error handler
[ 37.527772] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.527924] sd 6:0:4:0: [sdf] command ffff88010d5ea600 timed out
[ 37.527935] sas: Enter sas_scsi_recover_host busy: 6 failed: 6
[ 37.527942] sas: ata12: end_device-6:1: cmd error handler
[ 37.527946] sas: ata13: end_device-6:2: cmd error handler
[ 37.527949] sas: ata17: end_device-6:6: cmd error handler
[ 37.527952] sas: ata14: end_device-6:3: cmd error handler
[ 37.527956] sas: ata16: end_device-6:5: cmd error handler
[ 37.527959] sas: ata15: end_device-6:4: cmd error handler
[ 37.527971] sas: ata11: end_device-6:0: dev error handler
[ 37.527981] sas: ata12: end_device-6:1: dev error handler
[ 37.528021] sas: ata13: end_device-6:2: dev error handler
[ 37.528039] sas: ata14: end_device-6:3: dev error handler
[ 37.528056] sas: ata15: end_device-6:4: dev error handler
[ 37.528071] sas: ata16: end_device-6:5: dev error handler
[ 37.528087] sas: ata17: end_device-6:6: dev error handler
[ 37.528103] sas: ata18: end_device-6:7: dev error handler
[ 37.528115] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.528619] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 6 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.528624] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_94xx.c 626:command active 00000002, slot [0].
[ 37.528631] sd 6:0:6:0: [sdh] command ffff88010d543200 timed out
[ 37.528646] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 4 slot 1 rx_desc 30001 has error info0000000001000000.
[ 37.528652] sd 6:0:4:0: [sdf] command ffff88010d543000 timed out
[ 37.528664] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 3 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.528670] sd 6:0:3:0: [sde] command ffff88010d543d00 timed out
[ 37.528682] sas: Enter sas_scsi_recover_host busy: 3 failed: 3
[ 37.528686] sas: ata17: end_device-6:6: cmd error handler
[ 37.528690] sas: ata15: end_device-6:4: cmd error handler
[ 37.528692] sas: ata14: end_device-6:3: cmd error handler
[ 37.528705] sas: ata11: end_device-6:0: dev error handler
[ 37.528718] sas: ata12: end_device-6:1: dev error handler
[ 37.528726] sas: ata13: end_device-6:2: dev error handler
[ 37.528733] sas: ata14: end_device-6:3: dev error handler
[ 37.528750] sas: ata15: end_device-6:4: dev error handler
[ 37.528766] sas: ata16: end_device-6:5: dev error handler
[ 37.528774] sas: ata17: end_device-6:6: dev error handler
[ 37.528786] sas: ata18: end_device-6:7: dev error handler
[ 37.528797] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.528932] sd 13:0:1:0: [sdk] command ffff8801161a8600 timed out
[ 37.528945] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 37.528949] sas: ata21: end_device-13:2: cmd error handler
[ 37.528953] sas: ata20: end_device-13:1: cmd error handler
[ 37.528965] sas: ata19: end_device-13:0: dev error handler
[ 37.528975] sas: ata20: end_device-13:1: dev error handler
[ 37.528991] sas: ata21: end_device-13:2: dev error handler
[ 37.529007] sas: ata22: end_device-13:3: dev error handler
[ 37.529017] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.529897] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 0 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.529909] sd 13:0:0:0: [sdj] command ffff880115bfd600 timed out
[ 37.529931] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 37.529934] sas: ata19: end_device-13:0: cmd error handler
[ 37.529947] sas: ata19: end_device-13:0: dev error handler
[ 37.529965] sas: ata20: end_device-13:1: dev error handler
[ 37.529971] sas: ata21: end_device-13:2: dev error handler
[ 37.529986] sas: ata22: end_device-13:3: dev error handler
[ 37.529995] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.534557] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 1 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.534570] sd 13:0:1:0: [sdk] command ffff88010c9fc600 timed out
[ 37.534602] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 5 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.534608] sd 6:0:5:0: [sdg] command ffff88010ca04200 timed out
[ 37.534927] sd 13:0:3:0: [sdm] command ffff88010ca04500 timed out
[ 37.534946] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 37.534950] sas: ata20: end_device-13:1: cmd error handler
[ 37.534956] sas: ata22: end_device-13:3: cmd error handler
[ 37.534974] sas: ata19: end_device-13:0: dev error handler
[ 37.535004] sas: ata20: end_device-13:1: dev error handler
[ 37.535027] sas: ata21: end_device-13:2: dev error handler
[ 37.535033] sas: ata22: end_device-13:3: dev error handler
[ 37.535052] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.535532] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 5 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.535542] sd 13:0:3:0: [sdm] command ffff88010ca4a300 timed out
[ 37.535556] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 37.535559] sas: ata22: end_device-13:3: cmd error handler
[ 37.535572] sas: ata19: end_device-13:0: dev error handler
[ 37.535583] sas: ata20: end_device-13:1: dev error handler
[ 37.535588] sas: ata21: end_device-13:2: dev error handler
[ 37.535592] sas: ata22: end_device-13:3: dev error handler
[ 37.535609] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.538936] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 1 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.538950] sd 14:0:1:0: [sdo] command ffff88010d632800 timed out
[ 37.538965] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 37.538970] sas: ata24: end_device-14:1: cmd error handler
[ 37.538995] sas: ata23: end_device-14:0: dev error handler
[ 37.539013] sas: ata24: end_device-14:1: dev error handler
[ 37.539034] sas: ata25: end_device-14:2: dev error handler
[ 37.539043] sas: ata26: end_device-14:3: dev error handler
[ 37.539052] sas: ata27: end_device-14:4: dev error handler
[ 37.539061] sas: ata28: end_device-14:5: dev error handler
[ 37.539074] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.540962] sd 6:0:1:0: [sdc] command ffff88010ca04e00 timed out
[ 37.540990] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 37.540996] sas: ata16: end_device-6:5: cmd error handler
[ 37.541001] sas: ata12: end_device-6:1: cmd error handler
[ 37.541021] sas: ata11: end_device-6:0: dev error handler
[ 37.541033] sas: ata12: end_device-6:1: dev error handler
[ 37.541056] sas: ata13: end_device-6:2: dev error handler
[ 37.541062] sas: ata14: end_device-6:3: dev error handler
[ 37.541068] sas: ata15: end_device-6:4: dev error handler
[ 37.541073] sas: ata16: end_device-6:5: dev error handler
[ 37.541089] sas: ata17: end_device-6:6: dev error handler
[ 37.541095] sas: ata18: end_device-6:7: dev error handler
[ 37.541104] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.542215] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 6 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.542227] sd 14:0:4:0: [sdr] command ffff88010d551800 timed out
[ 37.542507] sd 14:0:0:0: [sdn] command ffff88010d551000 timed out
[ 37.542528] sas: Enter sas_scsi_recover_host busy: 2 failed: 2
[ 37.542532] sas: ata27: end_device-14:4: cmd error handler
[ 37.542538] sas: ata23: end_device-14:0: cmd error handler
[ 37.542556] sas: ata23: end_device-14:0: dev error handler
[ 37.542585] sas: ata24: end_device-14:1: dev error handler
[ 37.542591] sas: ata25: end_device-14:2: dev error handler
[ 37.542597] sas: ata26: end_device-14:3: dev error handler
[ 37.542602] sas: ata27: end_device-14:4: dev error handler
[ 37.542612] sas: ata28: end_device-14:5: dev error handler
[ 37.542622] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.542890] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 0 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.542898] sd 14:0:0:0: [sdn] command ffff88010d551300 timed out
[ 37.544877] /build/buildd/linux-lts-quantal-3.5.0/drivers/scsi/mvsas/mv_sas.c 1858:port 1 slot 0 rx_desc 30000 has error info0000000001000000.
[ 37.544890] sd 6:0:1:0: [sdc] command ffff88010ca42500 timed out
[ 37.545186] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 37.545191] sas: ata12: end_device-6:1: cmd error handler
[ 37.545210] sas: ata11: end_device-6:0: dev error handler
[ 37.545225] sas: ata12: end_device-6:1: dev error handler
[ 37.545243] sas: ata13: end_device-6:2: dev error handler
[ 37.545251] sas: ata14: end_device-6:3: dev error handler
[ 37.545257] sas: ata15: end_device-6:4: dev error handler
[ 37.545263] sas: ata16: end_device-6:5: dev error handler
[ 37.545268] sas: ata17: end_device-6:6: dev error handler
[ 37.545273] sas: ata18: end_device-6:7: dev error handler
[ 37.545283] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.564118] em28xx #0: i2c eeprom 00: 1a eb 67 95 04 23 27 02 d0 12 5c 03 8e 16 a4 1c
[ 37.564132] em28xx #0: i2c eeprom 10: 6a 24 27 57 46 07 01 00 00 00 00 00 00 00 00 00
[ 37.564141] em28xx #0: i2c eeprom 20: 46 00 01 00 f0 10 02 00 b8 00 00 00 5b 1c 00 00
[ 37.564151] em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 01 01 00 00 00 00 00 00
[ 37.564161] em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 37.564170] em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 37.564180] em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 24 03 50 00 69 00
[ 37.564189] em28xx #0: i2c eeprom 70: 6e 00 6e 00 61 00 63 00 6c 00 65 00 20 00 53 00
[ 37.564199] em28xx #0: i2c eeprom 80: 79 00 73 00 74 00 65 00 6d 00 73 00 00 00 16 03
[ 37.564209] em28xx #0: i2c eeprom 90: 50 00 43 00 54 00 56 00 20 00 38 00 30 00 30 00
[ 37.564219] em28xx #0: i2c eeprom a0: 65 00 00 00 1c 03 30 00 37 00 30 00 33 00 30 00
[ 37.564228] em28xx #0: i2c eeprom b0: 31 00 38 00 35 00 37 00 34 00 31 00 39 00 00 00
[ 37.564238] em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 37.564247] em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 37.564257] em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 37.564266] em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 37.564277] em28xx #0: EEPROM ID= 0x9567eb1a, EEPROM hash = 0xfae5a9bf
[ 37.564280] em28xx #0: EEPROM info:
[ 37.564281] em28xx #0: AC97 audio (5 sample rates)
[ 37.564283] em28xx #0: 500mA max power
[ 37.564284] em28xx #0: Table at 0x27, strings=0x168e, 0x1ca4, 0x246a
[ 37.564288] em28xx #0: Identified as Pinnacle PCTV HD Pro Stick (card=17)
[ 37.569020] sas: Enter sas_scsi_recover_host busy: 1 failed: 1
[ 37.569028] sas: ata23: end_device-14:0: cmd error handler
[ 37.569048] sas: ata23: end_device-14:0: dev error handler
[ 37.569073] sas: ata24: end_device-14:1: dev error handler
[ 37.569080] sas: ata25: end_device-14:2: dev error handler
[ 37.569085] sas: ata26: end_device-14:3: dev error handler
[ 37.569090] sas: ata27: end_device-14:4: dev error handler
[ 37.569095] sas: ata28: end_device-14:5: dev error handler
[ 37.569105] sas: --- Exit sas_scsi_recover_host: busy: 0 failed: 0
[ 37.737192] tvp5150 0-005c: chip found @ 0xb8 (em28xx #0)
[ 37.800486] tvp5150 0-005c: tvp5150am1 detected.
[ 37.926550] tuner 0-0061: Tuner -1 found with type(s) Radio TV.
[ 38.307347] xc2028 0-0061: creating new instance
[ 38.307352] xc2028 0-0061: type set to XCeive xc2028/xc3028 tuner
[ 38.490530] xc2028 0-0061: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7
[ 38.536016] xc2028 0-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
[ 38.782693] type=1400 audit(1357829731.782:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=1300 comm="apparmor_parser"
[ 38.782706] type=1400 audit(1357829731.782:3): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1299 comm="apparmor_parser"
[ 38.783132] type=1400 audit(1357829731.782:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1300 comm="apparmor_parser"
[ 38.783142] type=1400 audit(1357829731.782:5): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1299 comm="apparmor_parser"
[ 38.783378] type=1400 audit(1357829731.782:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=1300 comm="apparmor_parser"
[ 38.783391] type=1400 audit(1357829731.782:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1299 comm="apparmor_parser"
[ 38.783973] type=1400 audit(1357829731.782:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=1301 comm="apparmor_parser"
[ 38.784428] type=1400 audit(1357829731.786:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=1301 comm="apparmor_parser"
[ 38.784677] type=1400 audit(1357829731.786:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=1301 comm="apparmor_parser"
[ 39.039092] type=1400 audit(1357829732.038:11): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=1632 comm="apparmor_parser"
[ 39.587988] xc2028 0-0061: Loading firmware for type=MTS (4), id 000000000000b700.
[ 39.606235] xc2028 0-0061: Loading SCODE for type=MTS LCD NOGD MONO IF SCODE HAS_IF_4500 (6002b004), id 000000000000b700.
[ 39.728115] em28xx #0: Config register raw data: 0xd0
[ 39.728858] em28xx #0: AC97 vendor ID = 0xffffffff
[ 39.729233] em28xx #0: AC97 features = 0x6a90
[ 39.729234] em28xx #0: Empia 202 AC97 audio processor detected
[ 39.912987] em28xx #0: v4l2 driver version 0.1.3
[ 39.960028] xc2028 0-0061: Loading firmware for type=BASE F8MHZ MTS (7), id 0000000000000000.
[ 39.984511] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 40.325287] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: (null)
[ 41.007989] MTS (4), id 00000000000000ff:
[ 41.007995] xc2028 0-0061: Loading firmware for type=MTS (4), id 0000000100000007.
[ 41.235461] em28xx #0: V4L2 video device registered as video0
[ 41.235465] em28xx #0: V4L2 VBI device registered as vbi0
[ 41.237346] usbcore: registered new interface driver em28xx
[ 41.295415] sky2 0000:03:00.0: eth0: enabling interface
[ 41.295944] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 41.393491] em28xx-audio.c: probing for em28xx Audio Vendor Class
[ 41.393495] em28xx-audio.c: Copyright (C) 2006 Markus Rechberger
[ 41.393496] em28xx-audio.c: Copyright (C) 2007-2011 Mauro Carvalho Chehab
[ 41.393678] Em28xx: Initialized (Em28xx Audio Extension) extension
[ 41.466470] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[ 41.763763] EXT4-fs (dm-4): mounted filesystem with ordered data mode. Opts: (null)
[ 42.955242] xc2028 0-0061: attaching existing instance
[ 42.955247] xc2028 0-0061: type set to XCeive xc2028/xc3028 tuner
[ 42.955249] em28xx #0: em28xx #0/2: xc3028 attached
[ 42.955251] DVB: registering new adapter (em28xx #0)
[ 42.955254] DVB: registering adapter 0 frontend 0 (LG Electronics LGDT3303 VSB/QAM Frontend)...
[ 42.955641] em28xx #0: Successfully loaded em28xx-dvb
[ 42.955645] Em28xx: Initialized (Em28xx dvb Extension) extension
[ 43.528012] Registered IR keymap rc-pinnacle-pctv-hd
[ 43.528119] input: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.7/usb1/1-3/rc/rc0/input4
[ 43.528190] rc0: em28xx IR (em28xx #0) as /devices/pci0000:00/0000:00:1d.7/usb1/1-3/rc/rc0
[ 43.529736] Em28xx: Initialized (Em28xx Input Extension) extension
[ 43.844057] EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
[ 44.335747] sky2 0000:03:00.0: eth0: Link is up at 1000 Mbps, full duplex, flow control both
[ 44.336241] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 45.111890] EXT4-fs (dm-5): mounted filesystem with ordered data mode. Opts: (null)
[ 45.336064] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null)
[ 46.783565] RPC: Registered named UNIX socket transport module.
[ 46.783569] RPC: Registered udp transport module.
[ 46.783570] RPC: Registered tcp transport module.
[ 46.783572] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 47.240426] FS-Cache: Loaded
[ 47.595615] NFS: Registering the id_resolver key type
[ 47.595632] Key type id_resolver registered
[ 47.595634] Key type id_legacy registered
[ 47.595644] FS-Cache: Netfs 'nfs' registered for caching
[ 47.825390] Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
[ 48.796894] init: udev-fallback-graphics main process (1945) terminated with status 1
[ 54.029406] init: failsafe main process (1887) killed by TERM signal
[ 54.688732] audit_printk_skb: 6 callbacks suppressed
[ 54.688736] type=1400 audit(1357829747.690:14): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=2158 comm="apparmor_parser"
[ 54.689187] type=1400 audit(1357829747.690:15): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=2158 comm="apparmor_parser"
[ 54.689439] type=1400 audit(1357829747.690:16): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=2158 comm="apparmor_parser"
[ 54.691945] type=1400 audit(1357829747.690:17): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/ntpd" pid=2160 comm="apparmor_parser"
[ 54.732435] type=1400 audit(1357829747.734:18): apparmor="STATUS" operation="profile_load" name="/usr/sbin/mysqld" pid=2159 comm="apparmor_parser"
[ 54.734145] type=1400 audit(1357829747.734:19): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=2162 comm="apparmor_parser"
[ 55.580945] type=1400 audit(1357829748.582:20): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/mysqld" pid=2245 comm="apparmor_parser"
[ 58.357511] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 58.406871] NFSD: starting 90-second grace period
[ 73.520064] xc2028 0-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
[ 74.579991] xc2028 0-0061: Loading firmware for type=D2633 DTV6 ATSC (10030), id 0000000000000000.
[ 100.085777] nfsd: last server has exited, flushing export cache
[ 106.663300] init: mythtv-backend main process (2622) killed by TERM signal
[ 157.757723] type=1400 audit(1357829851.331:21): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/mysqld" pid=4422 comm="apparmor_parser"
[ 164.912019] xc2028 0-0061: Loading firmware for type=BASE MTS (5), id 0000000000000000.
[ 165.967944] xc2028 0-0061: Loading firmware for type=D2633 DTV6 ATSC (10030), id 0000000000000000.
[ 177.658572] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 177.658594] NFSD: starting 90-second grace period
[ 274.096452] init: tty1 main process ended, respawning
[ 277.840355] init: tty2 main process ended, respawning
[ 310.459102] st0: Block limits 1 - 16777215 bytes.
