Re: getting I/O errors in super_written()...any ideas what would cause this?

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 12/03/2012 02:36 PM, Chris Friesen wrote:
> On 12/03/2012 03:21 PM, Dave Jiang wrote:
>> On 12/03/2012 02:08 PM, Chris Friesen wrote:
>>> On 12/03/2012 02:52 PM, Ric Wheeler wrote:
>>>
>>>> I jumped into this thread late - can you repost detail on the specific
>>>> drive and HBA used here? In any case, it sounds like this is a better
>>>> topic for the linux-scsi or linux-ide list where most of the low level
>>>> storage people lurk :)
>>> Okay, expanding the receiver list. :)
>>>
>>> To recap:
>>>
>>> I'm running 2.6.27 with LVM over software RAID 1 over a pair of SAS disks.
>>> Disks are WD9001BKHG, controller is Intel C600.
>> Just curious what driver are you using with the C600. The upstream
>> driver for C600 didn't get accepted until 3.0-rc6 and all of the
>> outstanding patches weren't accepted until 3.7-rc. So I'd say 3.6 would
>> be your best bet until 3.7 is released. Did you attempt a backport of
>> the isci driver or using something like an LSI port on 2.6.27? Have you
>> verified the issue on a more recent kernel?
> We're using a driver provided by the hardware vendor.  It appears to be 
> a backport of version 1.0.1 of the isci driver.  We've been using it 
> since mid-March or so.

Yikes. There has been significant updates to libsas, libata, and isci
driver since March. Looks like you are barely limping along. I would
imagine the error handling and the hotplug would be a giant mess to say
the least.

> This is an embedded system, so as is all too common in that environment 
> upgrading the whole kernel isn't an option since it requires support 
> from multiple hardware/software vendors.
>
> Upgrading just the driver might be possible--do you think it's likely as 
> a cause for these errors?  The current driver has a binary firmware file 
> that it uses--would we keep that with the new driver?
You can certainly try but it needs the libsas, libata, and some block
fixes to function in a stable fashion. Given that it was a backport by a
vendor, one would wonder how much of libsas they actually backported.
It's really difficult to say where the error is coming from without
being able to verify on a later kernel. Is there any other I/O
controller you can use to test this? I'm guessing the answer is no since
it's embedded board. You are using a very old driver that is backported
to a very old kernel that requires significant subsystem backporting as
well. You may need to go poke your OS vendor and have them support the
issue?

The binary firmware file is really there in case you are not able to
load your OEM parameter properly from the platform. It's there to allow
you to limp if that is the case and by no means should be used for
standard operation. You are suppose to get the appropriate values for
your specific platform using a tool called phytune (which you should've
gotten from your Intel field rep). You need to program those values and
others into the OEM parameter block in the SPI flash of your platform.
In your BIOS you need to have either the OROM or the EFI driver loaded
during boot. The OROM or EFI driver then copies the values out of SPI
flash at boot and provides it to the driver. Those parameters provide
important timing values and others. If you are loading the wrong values
against your platform, it is very possible that you could see I/O errors.



> Chris


--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [SCSI Target Devel]     [Linux SCSI Target Infrastructure]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Linux IIO]     [Samba]     [Device Mapper]
  Powered by Linux