Hello, Aaron.
On Wed, Nov 14, 2012 at 10:18:23AM +0800, Aaron Lu wrote:
> On 11/13/2012 03:13 AM, Tejun Heo wrote:
> > Hello,
> >
> > On Fri, Nov 09, 2012 at 02:51:58PM +0800, Aaron Lu wrote:
> >> +#define POWEROFF_DELAY (30 * 1000) /* 30 seconds for power off delay */
> >> +
> >> struct zpodd {
> >> bool slot:1;
> >> bool drawer:1;
> >> bool from_notify:1; /* resumed as a result of acpi notification */
> >> + bool status_ready:1; /* ready status derived from media event poll,
> >> + it is not accurate, but serves as a hint */
> >> + bool zp_ready:1; /* zero power ready state */
> >> +
> >> + unsigned long last_ready; /* last zero power ready timestamp */
> >>
> >> struct ata_device *dev;
> >> };
> >
> > How are accesses to the bit fields synchronized?
>
> They are synchronized by PM core.
> PM core ensures that no two suspend or resume callback run concurrently.
> And when ODD is executing a command, it is in active state, no PM
> callback will run.
Care to add short comment for that? Flag and bitfield updates aren't
atomic to each other, so I find it usually helpful to clearly state
the synchronization rules for them. More so if locking is inherited
from upprer layer and not immediately obvious.
> > Hmmm... so, the "full" check only happens when autopm kicks in, right?
> > Is it really worth avoiding an extra TUR on autopm events? That's not
> > really a hot path. It seems a bit over-engineered to me.
>
> A little more information about this:
> When there is disc inside and no program mounted the drive, the ODD will
> be runtime suspended/resumed every 2 seconds along with the event poll.
Is that a desirable behavior? I haven't been following autopm and am
a bit fuzzy about how autopm works and what it does.
If there isn't any user of the device autopm kicks in. If zpodd is
enabled and there's no media, the device goes off power. If the user
initiates an event which may change media status, the driver is
notified via acpi and autopm backs out restoring power to the device.
Am I understanding it correctly?
What I'm confused about is what autopm does for devices w/o zpodd.
What happens then? Is it gonna leave power on for the device and,
say, go on to suspend the controller? But, how would that work for,
say, future devices with async notification for media events?
Also, if autopm is enabled, an optical device would go in and out of
suspend every two seconds?
> I'm not sure if the above situation can happen often. Normal desktop
> environment should automatically mount the ODD once they got uevent, and
> for console users, they will probably manually mount the drive after
> they have inserted a disc. The way I did it this way is to deal with the
> worst possible case. But if this is deemed as not necessary, I think I
> can remove the snoop hint thing and use TUR directly.
The problem with issuing TUR regularly is that some ODDs lock up after
getting hit by frequent TURs. That's the reason why sr event check
routine is being careful with TUR and only issue
GET_EVENT_STATUS_NOTIFICATION. Windows does about the same thing and
some vendors somehow screwed up TUR.
That said, I can't say the snooping is pretty. It's a rather nasty
thing to do. So, libata now wants information from the event polling
in block layer, but reaching for block_device from ata_devices is
nasty too. Hmmm... but aren't you already doing that to block polling
on a powered down device?
Thanks.
--
tejun
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
