Based on original implementation from Jiangbi Liu and Maciej Trela.
ATAPI transfers happen in two-to-three stages. The two stage atapi
commands are those that include a dma data transfer. The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration. The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.
stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb. Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).
stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.
stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.
To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO). This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).
If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition. However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response. In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.
Signed-off-by: Maciej Trela <maciej.trela@xxxxxxxxx>
Signed-off-by: Dan Williams <dan.j.williams@xxxxxxxxx>
---
drivers/scsi/isci/remote_device.c | 24 +++
drivers/scsi/isci/remote_device.h | 9 +
drivers/scsi/isci/request.c | 327 ++++++++++++++++++++++++++++++++++-
drivers/scsi/isci/request.h | 28 +++
drivers/scsi/libsas/sas_scsi_host.c | 2
include/scsi/libsas.h | 5 +
6 files changed, 379 insertions(+), 16 deletions(-)
diff --git a/drivers/scsi/isci/remote_device.c b/drivers/scsi/isci/remote_device.c
index b6e6368..fbf9ce2 100644
--- a/drivers/scsi/isci/remote_device.c
+++ b/drivers/scsi/isci/remote_device.c
@@ -386,6 +386,18 @@ static bool is_remote_device_ready(struct isci_remote_device *idev)
}
}
+/*
+ * called once the remote node context has transisitioned to a ready
+ * state (after suspending RX and/or TX due to early D2H fis)
+ */
+static void atapi_remote_device_resume_done(void *_dev)
+{
+ struct isci_remote_device *idev = _dev;
+ struct isci_request *ireq = idev->working_request;
+
+ sci_change_state(&ireq->sm, SCI_REQ_COMPLETED);
+}
+
enum sci_status sci_remote_device_event_handler(struct isci_remote_device *idev,
u32 event_code)
{
@@ -432,6 +444,16 @@ enum sci_status sci_remote_device_event_handler(struct isci_remote_device *idev,
if (status != SCI_SUCCESS)
return status;
+ if (state == SCI_STP_DEV_ATAPI_ERROR) {
+ /* For ATAPI error state resume the RNC right away. */
+ if (scu_get_event_type(event_code) == SCU_EVENT_TYPE_RNC_SUSPEND_TX ||
+ scu_get_event_type(event_code) == SCU_EVENT_TYPE_RNC_SUSPEND_TX_RX) {
+ return sci_remote_node_context_resume(&idev->rnc,
+ atapi_remote_device_resume_done,
+ idev);
+ }
+ }
+
if (state == SCI_STP_DEV_IDLE) {
/* We pick up suspension events to handle specifically to this
@@ -625,6 +647,7 @@ enum sci_status sci_remote_device_complete_io(struct isci_host *ihost,
case SCI_STP_DEV_CMD:
case SCI_STP_DEV_NCQ:
case SCI_STP_DEV_NCQ_ERROR:
+ case SCI_STP_DEV_ATAPI_ERROR:
status = common_complete_io(iport, idev, ireq);
if (status != SCI_SUCCESS)
break;
@@ -1020,6 +1043,7 @@ static const struct sci_base_state sci_remote_device_state_table[] = {
[SCI_STP_DEV_NCQ_ERROR] = {
.enter_state = sci_stp_remote_device_ready_ncq_error_substate_enter,
},
+ [SCI_STP_DEV_ATAPI_ERROR] = { },
[SCI_STP_DEV_AWAIT_RESET] = { },
[SCI_SMP_DEV_IDLE] = {
.enter_state = sci_smp_remote_device_ready_idle_substate_enter,
diff --git a/drivers/scsi/isci/remote_device.h b/drivers/scsi/isci/remote_device.h
index 57ccfc3..e1747ea 100644
--- a/drivers/scsi/isci/remote_device.h
+++ b/drivers/scsi/isci/remote_device.h
@@ -244,6 +244,15 @@ enum sci_remote_device_states {
SCI_STP_DEV_NCQ_ERROR,
/**
+ * This is the ATAPI error state for the STP ATAPI remote device.
+ * This state is entered when ATAPI device sends error status FIS
+ * without data while the device object is in CMD state.
+ * A suspension event is expected in this state.
+ * The device object will resume right away.
+ */
+ SCI_STP_DEV_ATAPI_ERROR,
+
+ /**
* This is the READY substate indicates the device is waiting for the RESET task
* coming to be recovered from certain hardware specific error.
*/
diff --git a/drivers/scsi/isci/request.c b/drivers/scsi/isci/request.c
index b5d3a8c..2bf072f 100644
--- a/drivers/scsi/isci/request.c
+++ b/drivers/scsi/isci/request.c
@@ -481,7 +481,29 @@ static void sci_stp_optimized_request_construct(struct isci_request *ireq,
}
}
+static void sci_atapi_construct(struct isci_request *ireq)
+{
+ struct host_to_dev_fis *h2d_fis = &ireq->stp.cmd;
+ struct sas_task *task;
+
+ /* To simplify the implementation we take advantage of the
+ * silicon's partial acceleration of atapi protocol (dma data
+ * transfers), so we promote all commands to dma protocol. This
+ * breaks compatibility with ATA_HORKAGE_ATAPI_MOD16_DMA drives.
+ */
+ h2d_fis->features |= ATAPI_PKT_DMA;
+
+ scu_stp_raw_request_construct_task_context(ireq);
+
+ task = isci_request_access_task(ireq);
+ if (task->data_dir == DMA_NONE)
+ task->total_xfer_len = 0;
+ /* clear the response so we can detect arrivial of an
+ * unsolicited h2d fis
+ */
+ ireq->stp.rsp.fis_type = 0;
+}
static enum sci_status
sci_io_request_construct_sata(struct isci_request *ireq,
@@ -491,6 +513,7 @@ sci_io_request_construct_sata(struct isci_request *ireq,
{
enum sci_status status = SCI_SUCCESS;
struct sas_task *task = isci_request_access_task(ireq);
+ struct domain_device *dev = ireq->target_device->domain_dev;
/* check for management protocols */
if (ireq->ttype == tmf_task) {
@@ -519,6 +542,13 @@ sci_io_request_construct_sata(struct isci_request *ireq,
}
+ /* ATAPI */
+ if (dev->sata_dev.command_set == ATAPI_COMMAND_SET &&
+ task->ata_task.fis.command == ATA_CMD_PACKET) {
+ sci_atapi_construct(ireq);
+ return SCI_SUCCESS;
+ }
+
/* non data */
if (task->data_dir == DMA_NONE) {
scu_stp_raw_request_construct_task_context(ireq);
@@ -627,7 +657,7 @@ enum sci_status sci_task_request_construct_sata(struct isci_request *ireq)
/**
* sci_req_tx_bytes - bytes transferred when reply underruns request
- * @sci_req: request that was terminated early
+ * @ireq: request that was terminated early
*/
#define SCU_TASK_CONTEXT_SRAM 0x200000
static u32 sci_req_tx_bytes(struct isci_request *ireq)
@@ -729,6 +759,10 @@ sci_io_request_terminate(struct isci_request *ireq)
case SCI_REQ_STP_SOFT_RESET_WAIT_H2D_ASSERTED:
case SCI_REQ_STP_SOFT_RESET_WAIT_H2D_DIAG:
case SCI_REQ_STP_SOFT_RESET_WAIT_D2H:
+ case SCI_REQ_ATAPI_WAIT_H2D:
+ case SCI_REQ_ATAPI_WAIT_PIO_SETUP:
+ case SCI_REQ_ATAPI_WAIT_D2H:
+ case SCI_REQ_ATAPI_WAIT_TC_COMP:
sci_change_state(&ireq->sm, SCI_REQ_ABORTING);
return SCI_SUCCESS;
case SCI_REQ_TASK_WAIT_TC_RESP:
@@ -1194,8 +1228,8 @@ static enum sci_status sci_stp_request_pio_data_out_transmit_data(struct isci_re
{
struct isci_stp_request *stp_req = &ireq->stp.req;
struct scu_sgl_element_pair *sgl_pair;
+ enum sci_status status = SCI_SUCCESS;
struct scu_sgl_element *sgl;
- enum sci_status status;
u32 offset;
u32 len = 0;
@@ -1249,7 +1283,7 @@ static enum sci_status sci_stp_request_pio_data_out_transmit_data(struct isci_re
*/
static enum sci_status
sci_stp_request_pio_data_in_copy_data_buffer(struct isci_stp_request *stp_req,
- u8 *data_buf, u32 len)
+ u8 *data_buf, u32 len)
{
struct isci_request *ireq;
u8 *src_addr;
@@ -1423,6 +1457,128 @@ static enum sci_status sci_stp_request_udma_general_frame_handler(struct isci_re
return status;
}
+static enum sci_status process_unsolicited_fis(struct isci_request *ireq,
+ u32 frame_index)
+{
+ struct isci_host *ihost = ireq->owning_controller;
+ enum sci_status status;
+ struct dev_to_host_fis *frame_header;
+ u32 *frame_buffer;
+
+ status = sci_unsolicited_frame_control_get_header(&ihost->uf_control,
+ frame_index,
+ (void **)&frame_header);
+
+ if (status != SCI_SUCCESS)
+ return status;
+
+ if (frame_header->fis_type != FIS_REGD2H) {
+ dev_err(&ireq->isci_host->pdev->dev,
+ "%s ERROR: invalid fis type 0x%X\n",
+ __func__, frame_header->fis_type);
+ return SCI_FAILURE;
+ }
+
+ sci_unsolicited_frame_control_get_buffer(&ihost->uf_control,
+ frame_index,
+ (void **)&frame_buffer);
+
+ sci_controller_copy_sata_response(&ireq->stp.rsp,
+ (u32 *)frame_header,
+ frame_buffer);
+
+ /* Frame has been decoded return it to the controller */
+ sci_controller_release_frame(ihost, frame_index);
+
+ return status;
+}
+
+static enum sci_status atapi_d2h_reg_frame_handler(struct isci_request *ireq,
+ u32 frame_index)
+{
+ struct sas_task *task = isci_request_access_task(ireq);
+ enum sci_status status;
+
+ status = process_unsolicited_fis(ireq, frame_index);
+
+ if (status == SCI_SUCCESS) {
+ if (ireq->stp.rsp.status & ATA_ERR)
+ status = SCI_IO_FAILURE_RESPONSE_VALID;
+ } else {
+ status = SCI_IO_FAILURE_RESPONSE_VALID;
+ }
+
+ if (status != SCI_SUCCESS) {
+ ireq->scu_status = SCU_TASK_DONE_CHECK_RESPONSE;
+ ireq->sci_status = status;
+ } else {
+ ireq->scu_status = SCU_TASK_DONE_GOOD;
+ ireq->sci_status = SCI_SUCCESS;
+ }
+
+ /* the d2h ufi is the end of non-data commands */
+ if (task->data_dir == DMA_NONE)
+ sci_change_state(&ireq->sm, SCI_REQ_COMPLETED);
+
+ return status;
+}
+
+static void scu_atapi_reconstruct_raw_frame_task_context(struct isci_request *ireq)
+{
+ struct ata_device *dev = sas_to_ata_dev(ireq->target_device->domain_dev);
+ void *atapi_cdb = ireq->ttype_ptr.io_task_ptr->ata_task.atapi_packet;
+ struct scu_task_context *task_context = ireq->tc;
+
+ /* fill in the SCU Task Context for a DATA fis containing CDB in Raw Frame
+ * type. The TC for previous Packet fis was already there, we only need to
+ * change the H2D fis content.
+ */
+ memset(&ireq->stp.cmd, 0, sizeof(struct host_to_dev_fis));
+ memcpy(((u8 *)&ireq->stp.cmd + sizeof(u32)), atapi_cdb, ATAPI_CDB_LEN);
+ memset(&(task_context->type.stp), 0, sizeof(struct stp_task_context));
+ task_context->type.stp.fis_type = FIS_DATA;
+ task_context->transfer_length_bytes = dev->cdb_len;
+}
+
+static void scu_atapi_construct_task_context(struct isci_request *ireq)
+{
+ struct ata_device *dev = sas_to_ata_dev(ireq->target_device->domain_dev);
+ struct sas_task *task = isci_request_access_task(ireq);
+ struct scu_task_context *task_context = ireq->tc;
+ int cdb_len = dev->cdb_len;
+
+ /* reference: SSTL 1.13.4.2
+ * task_type, sata_direction
+ */
+ if (task->data_dir == DMA_TO_DEVICE) {
+ task_context->task_type = SCU_TASK_TYPE_PACKET_DMA_OUT;
+ task_context->sata_direction = 0;
+ } else {
+ /* todo: for NO_DATA command, we need to send out raw frame. */
+ task_context->task_type = SCU_TASK_TYPE_PACKET_DMA_IN;
+ task_context->sata_direction = 1;
+ }
+
+ memset(&task_context->type.stp, 0, sizeof(task_context->type.stp));
+ task_context->type.stp.fis_type = FIS_DATA;
+
+ memset(&ireq->stp.cmd, 0, sizeof(ireq->stp.cmd));
+ memcpy(&ireq->stp.cmd.lbal, task->ata_task.atapi_packet, cdb_len);
+ task_context->ssp_command_iu_length = cdb_len / sizeof(u32);
+
+ /* task phase is set to TX_CMD */
+ task_context->task_phase = 0x1;
+
+ /* retry counter */
+ task_context->stp_retry_count = 0;
+
+ /* data transfer size. */
+ task_context->transfer_length_bytes = task->total_xfer_len;
+
+ /* setup sgl */
+ sci_request_build_sgl(ireq);
+}
+
enum sci_status
sci_io_request_frame_handler(struct isci_request *ireq,
u32 frame_index)
@@ -1833,6 +1989,24 @@ sci_io_request_frame_handler(struct isci_request *ireq,
return status;
}
+ case SCI_REQ_ATAPI_WAIT_PIO_SETUP: {
+ struct sas_task *task = isci_request_access_task(ireq);
+
+ sci_controller_release_frame(ihost, frame_index);
+ ireq->target_device->working_request = ireq;
+ if (task->data_dir == DMA_NONE) {
+ sci_change_state(&ireq->sm, SCI_REQ_ATAPI_WAIT_TC_COMP);
+ scu_atapi_reconstruct_raw_frame_task_context(ireq);
+ } else {
+ sci_change_state(&ireq->sm, SCI_REQ_ATAPI_WAIT_D2H);
+ scu_atapi_construct_task_context(ireq);
+ }
+
+ sci_controller_continue_io(ireq);
+ return SCI_SUCCESS;
+ }
+ case SCI_REQ_ATAPI_WAIT_D2H:
+ return atapi_d2h_reg_frame_handler(ireq, frame_index);
case SCI_REQ_ABORTING:
/*
* TODO: Is it even possible to get an unsolicited frame in the
@@ -1964,6 +2138,112 @@ stp_request_soft_reset_await_h2d_diagnostic_tc_event(struct isci_request *ireq,
return SCI_SUCCESS;
}
+static enum sci_status atapi_raw_completion(struct isci_request *ireq, u32 completion_code,
+ enum sci_base_request_states next)
+{
+ enum sci_status status = SCI_SUCCESS;
+
+ switch (SCU_GET_COMPLETION_TL_STATUS(completion_code)) {
+ case SCU_MAKE_COMPLETION_STATUS(SCU_TASK_DONE_GOOD):
+ ireq->scu_status = SCU_TASK_DONE_GOOD;
+ ireq->sci_status = SCI_SUCCESS;
+ sci_change_state(&ireq->sm, next);
+ break;
+ default:
+ /* All other completion status cause the IO to be complete.
+ * If a NAK was received, then it is up to the user to retry
+ * the request.
+ */
+ ireq->scu_status = SCU_NORMALIZE_COMPLETION_STATUS(completion_code);
+ ireq->sci_status = SCI_FAILURE_CONTROLLER_SPECIFIC_IO_ERR;
+
+ sci_change_state(&ireq->sm, SCI_REQ_COMPLETED);
+ break;
+ }
+
+ return status;
+}
+
+static enum sci_status atapi_data_tc_completion_handler(struct isci_request *ireq,
+ u32 completion_code)
+{
+ struct isci_remote_device *idev = ireq->target_device;
+ struct dev_to_host_fis *d2h = &ireq->stp.rsp;
+ enum sci_status status = SCI_SUCCESS;
+
+ switch (SCU_GET_COMPLETION_TL_STATUS(completion_code)) {
+ case (SCU_TASK_DONE_GOOD << SCU_COMPLETION_TL_STATUS_SHIFT):
+ sci_change_state(&ireq->sm, SCI_REQ_COMPLETED);
+ break;
+
+ case (SCU_TASK_DONE_UNEXP_FIS << SCU_COMPLETION_TL_STATUS_SHIFT): {
+ u16 len = sci_req_tx_bytes(ireq);
+
+ /* likely non-error data underrrun, workaround missing
+ * d2h frame from the controller
+ */
+ if (d2h->fis_type != FIS_REGD2H) {
+ d2h->fis_type = FIS_REGD2H;
+ d2h->flags = (1 << 6);
+ d2h->status = 0x50;
+ d2h->error = 0;
+ d2h->lbal = 0;
+ d2h->byte_count_low = len & 0xff;
+ d2h->byte_count_high = len >> 8;
+ d2h->device = 0xa0;
+ d2h->lbal_exp = 0;
+ d2h->lbam_exp = 0;
+ d2h->lbah_exp = 0;
+ d2h->_r_a = 0;
+ d2h->sector_count = 0x3;
+ d2h->sector_count_exp = 0;
+ d2h->_r_b = 0;
+ d2h->_r_c = 0;
+ d2h->_r_d = 0;
+ }
+
+ ireq->scu_status = SCU_TASK_DONE_GOOD;
+ ireq->sci_status = SCI_SUCCESS_IO_DONE_EARLY;
+ status = ireq->sci_status;
+
+ /* the hw will have suspended the rnc, so complete the
+ * request upon pending resume
+ */
+ sci_change_state(&idev->sm, SCI_STP_DEV_ATAPI_ERROR);
+ break;
+ }
+ case (SCU_TASK_DONE_EXCESS_DATA << SCU_COMPLETION_TL_STATUS_SHIFT):
+ /* In this case, there is no UF coming after.
+ * compelte the IO now.
+ */
+ ireq->scu_status = SCU_TASK_DONE_GOOD;
+ ireq->sci_status = SCI_SUCCESS;
+ sci_change_state(&ireq->sm, SCI_REQ_COMPLETED);
+ break;
+
+ default:
+ if (d2h->fis_type == FIS_REGD2H) {
+ /* UF received change the device state to ATAPI_ERROR */
+ status = ireq->sci_status;
+ sci_change_state(&idev->sm, SCI_STP_DEV_ATAPI_ERROR);
+ } else {
+ /* If receiving any non-sucess TC status, no UF
+ * received yet, then an UF for the status fis
+ * is coming after (XXX: suspect this is
+ * actually a protocol error or a bug like the
+ * DONE_UNEXP_FIS case)
+ */
+ ireq->scu_status = SCU_TASK_DONE_CHECK_RESPONSE;
+ ireq->sci_status = SCI_FAILURE_IO_RESPONSE_VALID;
+
+ sci_change_state(&ireq->sm, SCI_REQ_ATAPI_WAIT_D2H);
+ }
+ break;
+ }
+
+ return status;
+}
+
enum sci_status
sci_io_request_tc_completion(struct isci_request *ireq,
u32 completion_code)
@@ -2015,6 +2295,17 @@ sci_io_request_tc_completion(struct isci_request *ireq,
return request_aborting_state_tc_event(ireq,
completion_code);
+ case SCI_REQ_ATAPI_WAIT_H2D:
+ return atapi_raw_completion(ireq, completion_code,
+ SCI_REQ_ATAPI_WAIT_PIO_SETUP);
+
+ case SCI_REQ_ATAPI_WAIT_TC_COMP:
+ return atapi_raw_completion(ireq, completion_code,
+ SCI_REQ_ATAPI_WAIT_D2H);
+
+ case SCI_REQ_ATAPI_WAIT_D2H:
+ return atapi_data_tc_completion_handler(ireq, completion_code);
+
default:
dev_warn(&ihost->pdev->dev,
"%s: SCIC IO Request given task completion "
@@ -2421,6 +2712,8 @@ static void isci_process_stp_response(struct sas_task *task, struct dev_to_host_
*/
if (fis->status & ATA_DF)
ts->stat = SAS_PROTO_RESPONSE;
+ else if (fis->status & ATA_ERR)
+ ts->stat = SAM_STAT_CHECK_CONDITION;
else
ts->stat = SAM_STAT_GOOD;
@@ -2791,6 +3084,7 @@ static void sci_request_started_state_enter(struct sci_base_state_machine *sm)
{
struct isci_request *ireq = container_of(sm, typeof(*ireq), sm);
struct domain_device *dev = ireq->target_device->domain_dev;
+ enum sci_base_request_states state;
struct sas_task *task;
/* XXX as hch said always creating an internal sas_task for tmf
@@ -2802,26 +3096,29 @@ static void sci_request_started_state_enter(struct sci_base_state_machine *sm)
* substates
*/
if (!task && dev->dev_type == SAS_END_DEV) {
- sci_change_state(sm, SCI_REQ_TASK_WAIT_TC_COMP);
+ state = SCI_REQ_TASK_WAIT_TC_COMP;
} else if (!task &&
(isci_request_access_tmf(ireq)->tmf_code == isci_tmf_sata_srst_high ||
isci_request_access_tmf(ireq)->tmf_code == isci_tmf_sata_srst_low)) {
- sci_change_state(sm, SCI_REQ_STP_SOFT_RESET_WAIT_H2D_ASSERTED);
+ state = SCI_REQ_STP_SOFT_RESET_WAIT_H2D_ASSERTED;
} else if (task && task->task_proto == SAS_PROTOCOL_SMP) {
- sci_change_state(sm, SCI_REQ_SMP_WAIT_RESP);
+ state = SCI_REQ_SMP_WAIT_RESP;
} else if (task && sas_protocol_ata(task->task_proto) &&
!task->ata_task.use_ncq) {
- u32 state;
-
- if (task->data_dir == DMA_NONE)
+ if (dev->sata_dev.command_set == ATAPI_COMMAND_SET &&
+ task->ata_task.fis.command == ATA_CMD_PACKET) {
+ state = SCI_REQ_ATAPI_WAIT_H2D;
+ } else if (task->data_dir == DMA_NONE) {
state = SCI_REQ_STP_NON_DATA_WAIT_H2D;
- else if (task->ata_task.dma_xfer)
+ } else if (task->ata_task.dma_xfer) {
state = SCI_REQ_STP_UDMA_WAIT_TC_COMP;
- else /* PIO */
+ } else /* PIO */ {
state = SCI_REQ_STP_PIO_WAIT_H2D;
-
- sci_change_state(sm, state);
+ }
+ } else {
+ BUG();
}
+ sci_change_state(sm, state);
}
static void sci_request_completed_state_enter(struct sci_base_state_machine *sm)
@@ -2913,6 +3210,10 @@ static const struct sci_base_state sci_request_state_table[] = {
[SCI_REQ_TASK_WAIT_TC_RESP] = { },
[SCI_REQ_SMP_WAIT_RESP] = { },
[SCI_REQ_SMP_WAIT_TC_COMP] = { },
+ [SCI_REQ_ATAPI_WAIT_H2D] = { },
+ [SCI_REQ_ATAPI_WAIT_PIO_SETUP] = { },
+ [SCI_REQ_ATAPI_WAIT_D2H] = { },
+ [SCI_REQ_ATAPI_WAIT_TC_COMP] = { },
[SCI_REQ_COMPLETED] = {
.enter_state = sci_request_completed_state_enter,
},
diff --git a/drivers/scsi/isci/request.h b/drivers/scsi/isci/request.h
index 7a1d5a9..1fd4f07 100644
--- a/drivers/scsi/isci/request.h
+++ b/drivers/scsi/isci/request.h
@@ -96,7 +96,6 @@ enum sci_request_protocol {
* to wait for another fis or if the transfer is complete. Upon
* receipt of a d2h fis this will be the status field of that fis.
* @sgl - track pio transfer progress as we iterate through the sgl
- * @device_cdb_len - atapi device advertises it's transfer constraints at setup
*/
struct isci_stp_request {
u32 pio_len;
@@ -107,7 +106,6 @@ struct isci_stp_request {
u8 set;
u32 offset;
} sgl;
- u32 device_cdb_len;
};
struct isci_request {
@@ -252,6 +250,32 @@ enum sci_base_request_states {
SCI_REQ_STP_PIO_DATA_OUT,
/*
+ * While in this state the IO request object is waiting for the TC
+ * completion notification for the H2D Register FIS
+ */
+ SCI_REQ_ATAPI_WAIT_H2D,
+
+ /*
+ * While in this state the IO request object is waiting for either a
+ * PIO Setup.
+ */
+ SCI_REQ_ATAPI_WAIT_PIO_SETUP,
+
+ /*
+ * The non-data IO transit to this state in this state after receiving
+ * TC completion. While in this state IO request object is waiting for
+ * D2H status frame as UF.
+ */
+ SCI_REQ_ATAPI_WAIT_D2H,
+
+ /*
+ * When transmitting raw frames hardware reports task context completion
+ * after every frame submission, so in the non-accelerated case we need
+ * to expect the completion for the "cdb" frame.
+ */
+ SCI_REQ_ATAPI_WAIT_TC_COMP,
+
+ /*
* The AWAIT_TC_COMPLETION sub-state indicates that the started raw
* task management request is waiting for the transmission of the
* initial frame (i.e. command, task, etc.).
diff --git a/drivers/scsi/libsas/sas_scsi_host.c b/drivers/scsi/libsas/sas_scsi_host.c
index ebd1417..b2c4a77 100644
--- a/drivers/scsi/libsas/sas_scsi_host.c
+++ b/drivers/scsi/libsas/sas_scsi_host.c
@@ -801,7 +801,7 @@ void sas_slave_destroy(struct scsi_device *scsi_dev)
struct domain_device *dev = sdev_to_domain_dev(scsi_dev);
if (dev_is_sata(dev))
- dev->sata_dev.ap->link.device[0].class = ATA_DEV_NONE;
+ sas_to_ata_dev(dev)->class = ATA_DEV_NONE;
}
int sas_change_queue_depth(struct scsi_device *sdev, int depth, int reason)
diff --git a/include/scsi/libsas.h b/include/scsi/libsas.h
index 0d78bfa..6d5185c 100644
--- a/include/scsi/libsas.h
+++ b/include/scsi/libsas.h
@@ -383,6 +383,11 @@ sdev_to_domain_dev(struct scsi_device *sdev) {
return starget_to_domain_dev(sdev->sdev_target);
}
+static inline struct ata_device *sas_to_ata_dev(struct domain_device *dev)
+{
+ return &dev->sata_dev.ap->link.device[0];
+}
+
static inline struct domain_device *
cmd_to_domain_dev(struct scsi_cmnd *cmd)
{
--
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
